Autor: Kozik, B - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: Defining instantaneous contact track of aeronautical bevel gear applying finite elements method and rapid prototyping method
Autorzy:: Pacana, J.
Kozik, B.
Budzik, G.
Powiązania:: https://bibliotekanauki.pl/articles/246384.pdf
Data publikacji:: 2010
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: contact track
FEM
bevel gear
Opis:: An instantaneous contact track is one of theparameters determining correct work of wheels in gears. It is the surface on the side of the tooth on which a contact is made with the cooperating surface of the other wheel in a given moment. The correctness of cooperation of wheels and kinematic accuracy of the gear depends on the shape and the size of an instantaneous contact track and its changes during rotation of wheels. Both the area of contact track and its position also depend on the greatness of load being in operation. Therefore it is important to carry out calculations for conditions of work which are the closest to real working conditions of aeronautical bevels gear. At the designing stage an instantaneous contact track can be determined by means of finite elements method (FEM). The article presents a methodology of defi ning contact track for loaded bevel gear by means of numerical finite elements method. The paper also presents Information about creating virtual models ofwheels, generating network of finite elements, defining edge conditions as well as carrying out calculations and processing the received results. Finally, it also presents the received solutions concerning the distribution of reduced stresses andan instantaneous contact track as well as the summary track of wheel teeth cooperation in a loaded bevel gear. However the results received by means of simulation of virtual models cooperation require verifying by other methods, favourably experimental ones. The received numerical solutions made using finite elements method were therefore compared to proper results recorded during examining real models of the same wheels. The examination was carried out on a special stand which had been designed end created for this purpose. The used wheels had been made by means of rapid prototyping method.
Źródło:: Journal of KONES; 2010, 17, 2; 379-386
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Determining of model similarity for flexspline of harmonic drive with the use of FEM and extensometer method
Autorzy:: Budzik, G.
Kozik, B.
Pacana, J.
Powiązania:: https://bibliotekanauki.pl/articles/242442.pdf
Data publikacji:: 2009
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: mechanics
harmonic drives
flexspline
FEM
extensometers
Opis:: This paper presents an analysis of the feasibility of using the model similarity method in engineering design. The analysis applies to virtual and physical models of the flexspline body of harmonic gear drive. The task consisted in determining stress distribution in the virtual models of the flexspline by means of the finite element method (FEM) and next its verification during bench tests by the extensometer method. The values of stresses calculated by the FEM method and the extensometer method were compared with each other with the aim ofdefming model similarity. The numerical calculations were made by means of the ADINA application which uses FEM with the use of contact elements. Stress distribution calculations applied to simplified virtual models of the flexspline. By the simplification of models a great number of finite elements used for the discretisation process were limited and because of that the time of calculations was shortened. The simplified model was precise enough to determine the stresses in the flexspline body. The subject of this analysis was the impact of different values of the torque moment T2 on the stresses in the flexspline body of the harmonie drive. The results of numerical calculations were checked against the standing tests of the real drive by applying the extensometer method. During the work of the gear, the values of relative elongation were measured and, based on them, the values of stresses were determined and compared to the results of the numerical calculations by FEM in the analogous cross-sections of the flexspline. The comparability of the results received by both methods proves both that the models used in the numerical calculations were properly designed and that the assumptions as well as the calculation were properly made. The determining of model similarity for the examined harmonie drive will make it possible to carry out analyses of stress calculations by FEM on virtual models without the necessity to verify them by laboratory standing tests each time.
Źródło:: Journal of KONES; 2009, 16, 2; 55-60
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Strength analysis of gears in dual-path gearing by means of FEM
Analiza wytrzymałościowa kół zębatej przekładni dwudrożnej z zastosowaniem MES
Autorzy:: Pacana, J.
Kozik, B.
Budzik, G.
Powiązania:: https://bibliotekanauki.pl/articles/328491.pdf
Data publikacji:: 2015
Wydawca:: Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:: dual-path gearing
FEM
strength analysis
diagnostics
przekładnia dwudrożna
MES
analiza wytrzymałościowa
diagnostyka
Opis:: The paper contains a strength analysis of gears in a dual-path gearing made of plastic. Computation was carried out using Abaqus program by means of finite elements method (FEM). The results of calculations allow the interpretation of the results of diagnostic tests. Due to the fact that the dual-path gearing had wheels with straight teeth, it was possible to simplify the computation using two-dimensional models. The paper shows activities related to preparation of models, defining boundary conditions, the process of computation and the presentation and interpretation of obtained results. In the carried out FEM analysis, stress distribution was determined on models of pinions and gears, paying particular attention to key points like teeth feet or their flanks. In order to improve readability of these solutions and to ease interpretation, some results were also presented in a form of charts. Conclusions drawn from the analysis will make it possible to introduce conceivable changes in the structure of designed gearing already at the stage of modelling.
Niniejsze opracowanie zawiera prezentację przebiegu obliczeń wytrzymałościowych kół zębatych przekładni dwudrożnej przeprowadzonych w programie Abakus z wykorzystaniem metody elementów skończonych (MES). Wyniki obliczeń pozwolą na interpretację wyników badań diagnostycznych. Zaprezentowane zostały działania związane z przygotowaniem modeli, definiowaniem warunków brzegowych, przebiegiem obliczeń, oraz prezentacją i interpretacją otrzymanych wyników. W przeprowadzonej analizie MES wyznaczono rozkłady naprężeń na modelach zębników i koła zębatego, zwracając szczególną uwagę na miejsca kluczowe jak podstawy zębów, czy ich powierzchnie boczne. W celu poprawienia czytelności rozwiązań i ułatwienia ich interpretacji wybrane wyniki zostały także zaprezentowane w formie wykresów. Wnioski otrzymane w wyniku przeprowadzonej analizy pozwolą na wprowadzenie ewentualnych zmian w konstrukcji projektowanej przekładni już na etapie modelowania.
Źródło:: Diagnostyka; 2015, 16, 1; 41-46
1641-6414
2449-5220
Pojawia się w:: Diagnostyka
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "Kozik, B" wg kryterium: Autor

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język