Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Ali, M. A. N." wg kryterium: Autor


Wyświetlanie 1-2 z 2
Tytuł:
Effect of operating parameters on production of bio-oil from fast pyrolysis of maize stalk in bubbling fluidized bed reactor
Autorzy:
Ali, N.
Saleem, M.
Shahzad, K.
Hussain, S.
Chughtai, A.
Powiązania:
https://bibliotekanauki.pl/articles/779892.pdf
Data publikacji:
2016
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
fast pyrolysis
bio-oil
temperature
particle size
carrier gas flow rate
maize stalk
Opis:
The yield and composition of pyrolysis products depend on the characteristics of feed stock and process operating parameters. Effect of particle size, reaction temperature and carrier gas flow rate on the yield of bio-oil from fast pyrolysis of Pakistani maize stalk was investigated. Pyrolysis experiments were performed at temperature range of 360-540°C, feed particle size of 1-2 mm and carrier gas flow rate of 7.0-13.0 m3/h (0.61.1 m/s superficial velocity). Bio-oil yield increased with the increase of temperature followed by a decreasing trend. The maximum yield of bio-oil obtained was 42 wt% at a temperature of 490°C with the particle size of around 1.0 mm and carrier gas flow rate of 11.0 m3/h (0.9 m/s superficial velocity). High temperatures resulted in the higher ratios of char and non-condensable gas.
Źródło:
Polish Journal of Chemical Technology; 2016, 18, 3; 88-96
1509-8117
1899-4741
Pojawia się w:
Polish Journal of Chemical Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
An alternative and indirect statistical modeling method for viscosity estimation and its experimental validation for low styrene content polyester resin
Autorzy:
Nawaz, A.
Islam, B.
Ijaz, M. Z.
Saleem, U.
Khattak, M. S.
Ahmad, S. N.
Maqsood, N.
Ali, L.
Powiązania:
https://bibliotekanauki.pl/articles/778495.pdf
Data publikacji:
2018
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
indirect method
polyester resin
statistical relation
Ford viscosity cup
Opis:
We propose an indirect method of ASTM D-1200 for measurement of viscosity from 0.1 to 30 stokes (St) using Ford cup 5 (range 2~ 12 St) by developing a statistical relation. General purpose low styrene content polyester resin (without adding initiator, hardener and accelerator) was used for viscosity measurement. In existing ASTM D 1200 standard, ford cups (1-4) are used to measure the viscosity up to 2 St, while fifth cup is used for measurement from 2 to 12 St. Viscosity above 12 St is not estimated using existing ASTM D- 1200 method. In contrast, our method and statistical relation proposed in this paper estimates viscosity in the flexible range of 0.1 to 30 St by using Ford cup 5 only. The estimated values were confirmed by existing ASTM D-1200 (0.1 to 12 St) and by using Ubbelohde viscometer (12 to 30 St). Values estimated above 12 St are from the proposed model are also in good conformance (percentage error ~ 5% or less) with experimental results. The satisfaction level of the estimated values with the experiments suggests that the model has also the potential for application to paints, polymer and oil industry.
Źródło:
Polish Journal of Chemical Technology; 2018, 20, 4; 60-65
1509-8117
1899-4741
Pojawia się w:
Polish Journal of Chemical Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies