Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "przenikanie ciepła" wg kryterium: Temat


Wyświetlanie 1-10 z 10
Tytuł:
The effect of regulating elements on convective heat transfer along shaped heat exchange surfaces
Autorzy:
Cernecky, J.
Koniar, J.
Brodnianska, Z.
Powiązania:
https://bibliotekanauki.pl/articles/185818.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat transfer
convection
holographic interferometry
przenikanie ciepła
konwekcja
interferometria holograficzna
Opis:
The paper deals with a study of the effect of regulating elements on local values of heat transfer coefficients along shaped heat exchange surfaces with forced air convection. The use of combined methods of heat transfer intensification, i.e. a combination of regulating elements with appropriately shaped heat exchange areas seems to be highly effective. The study focused on the analysis of local values of heat transfer coefficients in indicated cuts, in distances expressed as a ratio x/s for 0; 0.33; 0.66 and 1. As can be seen from our findings, in given conditions the regulating elements can increase the values of local heat transfer coefficients along shaped heat exchange surfaces. An optical method of holographic interferometry was used for the experimental research into temperature fields in the vicinity of heat exchange surfaces. The obtained values correspond very well with those of local heat transfer coefficients [alfa]x, recorded in a CFD simulation.
Źródło:
Chemical and Process Engineering; 2013, 34, 1; 5-16
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigations on heat and momentum transfer in CuO-water nanofluid
Autorzy:
Dzido, G.
Drzazga, M.
Lemanowicz, M.
Gierczycki, A. T.
Powiązania:
https://bibliotekanauki.pl/articles/240561.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nanofluids
fluid mechanics
heat transfer
nanopłyny
mechanika płynów
przenikanie ciepła
Opis:
This paper presents results of investigations on the application of CuO-water nanofluids for intensification of convective heat transfer. Performance of nanofluids with 2.2 and 4.0 vol.% CuO NPs (nanoparticles) content were examined with regard to heat transfer coefficient and pressure losses in case of turbulent flow in a tube. Negligible impact of examined nanofluid on heat transfer improvement was found. Moreover, measured pressure losses significantly exceeded those determined for primary base liquid. The observations showed that application of nanofluid for heat transfer intensification with a relatively high solid load in the examined flow range is rather controversial.
Źródło:
Archives of Thermodynamics; 2015, 36, 2; 49-59
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Burner Locations in the Heating Furnace on the Charge Temperature Field
Wpływ usytuowania palników w piecu grzewczym na pole temperatury nagrzewanego wsadu do przeróbki plastycznej
Autorzy:
Rywotycki, M.
Szajding, A.
Malinowski, Z.
Telejko, T.
Gołdasz, A.
Beneš, M.
Powiązania:
https://bibliotekanauki.pl/articles/351620.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
industrial furnaces
heat transfer
numerical modelling
piece przemysłowe
przenikanie ciepła
modelowanie numeryczne
Opis:
Charge heating in industrial furnaces is a difficult and complex process. There are many physical phenomena which influence heat transfer. At the charge surface heat transfer takes place by radiation and convection. In order to ensure correct operation of the technological system, it is necessary to achieve the required charge temperature in the whole volume and ensure its uniformity. The influence of selected burner locations inside the furnace on the charge temperature has been analysed. The temperature field and its uniformity in the round charge made of steel for hot open die forging have been analysed. The model and numerical calculations were performed with the ANSYS-Fluent 14.5 package.
Nagrzewanie wsadu w piecach przemysłowych jest trudnym i złożonym procesem. Celem zapewnienia prawidłowej pracy ciągu technologicznego konieczne jest osiągnięcie przez wsad wymaganej temperatury w całej objętości, oraz zapewnienie odpowiedniej równomierności nagrzewania. W pracy określono wpływ sposobu nagrzewania wsadu w piecu komorowym dla wybranych wariantów usytuowania palników grzewczych. Analizie poddano pole temperatury i jego jednorodność w nagrzewanym wsadzie stalowym przeznaczonym do przeróbki plastycznej. Model i obliczenia wykonano pakietem numerycznym ANSYS-Fluent 14.5.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 3A; 1981-1985
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Intensification of heat transfer between heat exchange surfaces at low RE values
Autorzy:
Cernecky, J.
Brodnianska, Z.
Koniar, J.
Powiązania:
https://bibliotekanauki.pl/articles/184897.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat transfer
heat exchange surface
Colburn j-factor
interferometry
przenikanie ciepła
powierzchnia wymiany ciepła
interferometria
Opis:
This contribution deals with the heat transfer parameters and pressure losses in heat exchange sets with six geometrical arrangements at low Re values (Re from 476 to 2926). Geometrical arrangements were characterised by the h/H ratio ranging from 0.2 to 1.0. The experiments used the holographic interferometry method in real time. This method enables visible and quantitative evaluations of images of temperature fields in the examined heat exchange. These images are used to determine the local and mean heat transfer parameters. The obtained data were used to determine the Colburn j-factor and the friction coefficient f. The measured values show that by using the profiled heat exchange surfaces and inserting regulating tubes, an intensification of heat transfer (increase of Num, and/or j) was achieved. However, pressure losses recorded a significant increase (increase of f).
Źródło:
Chemical and Process Engineering; 2015, 36, 3; 331-344
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical analysis of the steam flow field in shell and tube heat exchanger
Autorzy:
Bartoszewicz, J.
Bogusławski, L.
Powiązania:
https://bibliotekanauki.pl/articles/240429.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat transfer
heat exchanger
shell and tube heat exchanger
przenikanie ciepła
wymiennik ciepła
wymiennik płaszczowo-rurowy
Opis:
In the paper, the results of numerical simulations of the steam flow in a shell and tube heat exchanger are presented. The efficiency of different models of turbulence was tested. In numerical calculations the following turbulence models were used: k-ε, RNG k-ε, Wilcox k-ω, Chen-Kim k-ε, and Lam-Bremhorst k-ε. Numerical analysis of the steam flow was carried out assuming that the flow at the inlet section of the heat exchanger were divided into three parts. The angle of steam flow at inlet section was determined individually in order to obtain the best configuration of entry vanes and hence improve the heat exchanger construction. Results of numerical studies were verified experimentally for a real heat exchanger. The modification of the inlet flow direction according to theoretical considerations causes the increase of thermal power of a heat exchanger of about 14%.
Źródło:
Archives of Thermodynamics; 2016, 37, 2; 107-120
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental determination of correlations for mean heat transfer coefficients in plate fin and tube heat exchangers
Autorzy:
Taler, D.
Powiązania:
https://bibliotekanauki.pl/articles/239992.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
model matematyczny
przenikanie ciepła
wymiennik ciepła
heat transfer correlations
mathematical model
tube and plate fin heat exchangers
Opis:
This paper presents a numerical method for determining heat transfer coefficients in cross-flow heat exchangers with extended heat exchange surfaces. Coefficients in the correlations defining heat transfer on the liquid- and air-side were determined using a nonlinear regression method. Correlation coefficients were determined from the condition that the sum of squared liquid and air temperature differences at the heat exchanger outlet, obtained by measurements and those calculated, achieved minimum. Minimum of the sum of the squares was found using the Levenberg-Marquardt method. The uncertainty in estimated parameters was determined using the error propagation rule by Gauss. The outlet temperature of the liquid and air leaving the heat exchanger was calculated using the analytical model of the heat exchanger.
Źródło:
Archives of Thermodynamics; 2012, 33, 3; 3-26
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
CFD Analysis of Heat Transfer in a Microtubular Solid Oxide Fuel Cell Stack
Autorzy:
Pianko-Oprych, P.
Kasilova, E.
Jaworski, Z.
Powiązania:
https://bibliotekanauki.pl/articles/185553.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
przenikanie ciepła
strata ciepła
rozkład temperatur
microtubular Solid Oxide Fuel Cell stack
heat transfer
heat losses
temperature distributions
computational fluid dynamics (CFD)
Opis:
The aim of this work was to achieve a deeper understanding of the heat transfer in a microtubular Solid Oxide Fuel Cell (mSOFC) stack based on the results obtained by means of a Computational Fluid Dynamics tool. Stack performance predictions were based on simulations for a 16 anodesupported mSOFCs sub-stack, which was a component of the overall stack containing 64 fuel cells. The emphasis of the paper was put on steadystate modelling, which enabled identification of heat transfer between the fuel cells and air flow cooling the stack and estimation of the influence of stack heat losses. Analysis of processes for different heat losses and the impact of the mSOFC reaction heat flux profile on the temperature distribution in the mSOFC stack were carried out. Both radiative and convective heat transfer were taken into account in the analysis. Two different levels of the inlet air velocity and three different values of the heat losses were considered. Good agreement of the CFD model results with experimental data allowed to predict the operation trends, which will be a reliable tool for optimisation of the working setup and ensure sufficient cooling of the mSOFC stack.
Źródło:
Chemical and Process Engineering; 2014, 35, 3; 293-304
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research on the Portuguese building stock and its impacts on energy consumption – an average U-value approach
Autorzy:
Sousa, J.
Bragança, L.
Almeida, M.
Silva, P.
Powiązania:
https://bibliotekanauki.pl/articles/231236.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
zasoby budynków
zasoby energii
zużycie energii
element konstrukcyjny
przenikanie ciepła
współczynnik przenikania ciepła
building stock
energy resources
energy consumption
structural element
heat transfer
heat transfer coefficient
Opis:
The article aims to evaluate the Portuguese building stock energy policies and strategy for energy saving in buildings among the EU members. It was found out the average heat transfer coefficients of the main structural elements of Portuguese Buildings and analyzed the U-values of this elements considering different time periods. The fundamentals of this study were funded by the Agency for Development and Innovation (ADI) and co-financed by the European Regional Development Fund (FEDER) through the Operational Program for Competitiveness Factors (POFC) assigned to the Building Physics and Construction Technology Laboratory with the reference SB Tool SPT_2011_4.
Źródło:
Archives of Civil Engineering; 2013, 59, 4; 523-546
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Transient analysis of heat transfer across the residential building roof with PCM and wood wool - A case study by numerical simulation approach
Autorzy:
Prakash, D.
Ravikumar, P.
Powiązania:
https://bibliotekanauki.pl/articles/230999.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
przenikanie ciepła
budynek mieszkalny
dach
materiał zmieniający fazę
wełna drzewna
symulacja numeryczna
heat transfer
residential building
roof
phase change material
wood wool
numerical simulation
Opis:
In this paper, transient analysis on heat transfer across the residential building roof having various materials like wood wool, phase change material and weathering tile is performed by numerical simulation technique. 2-dimensional roof model is created, checked for grid independency and validated with the experimental results. Three different roof structures are included in this study namely roof with (i). Concrete and weathering tile, (ii). Concrete, phase change material and weathering tile and (iii). Concrete, phase change material, wood wool and weathering tile. Roof type 3 restricts 13% of heat entering the room in comparison with roof having only concrete and weathering tile. Also the effect of various roof layers’ thickness in the roof type 3 is investigated and identified that the wood wool plays the major role in arresting the entry of heat in to the room. The average reduction of heat is about 10 % for an increase of a unit thickness of wood wool layer.
Źródło:
Archives of Civil Engineering; 2013, 59, 4; 483-497
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modeling of Melting and Resolidification in Domain of Metal Film Subjected to a Laser Pulse
Autorzy:
Majchrzak, E.
Mochnacki, B.
Powiązania:
https://bibliotekanauki.pl/articles/379913.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
foundry process
heat transfer
melting
solidification
dual phase lag model
numerical methods
theoretical basis
proces odlewniczy
przenikanie ciepła
topienie
krzepnięcie
model dwufazowy
metody numeryczne
podstawy teoretyczne
Opis:
Thermal processes in domain of thin metal film subjected to a strong laser pulse are discussed. The heating of domain considered causes the melting and next (after the end of beam impact) the resolidification of metal superficial layer. The laser action (a time dependent bell-type function) is taken into account by the introduction of internal heat source in the energy equation describing the heat transfer in domain of metal film. Taking into account the extremely short duration, extreme temperature gradients and very small geometrical dimensions of the domain considered, the mathematical model of the process is based on the dual phase lag equation supplemented by the suitable boundary-initial conditions. To model the phase transitions the artificial mushy zone is introduced. At the stage of numerical modeling the Control Volume Method is used. The examples of computations are also presented.
Źródło:
Archives of Foundry Engineering; 2016, 16, 1; 41-44
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-10 z 10

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies