Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "crystal orientation" wg kryterium: Temat


Wyświetlanie 1-3 z 3
Tytuł:
Influence of crystallographic orientation on creep resistance of single-crystal superalloy
Autorzy:
Kościelniak, Barbara
Gancarczyk, Kamil
Poręba, Marek
Albrecht, Robert
Powiązania:
https://bibliotekanauki.pl/articles/176142.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
CMSX-4 superalloys
creep resistance
crystal orientation
microstructure
Opis:
This paper focuses on the influence of crystallographic orientation on creep resistance of CMSX-4 nickel-based superalloy. The single-crystal rods of CMSX-4 superalloy were manufactured with the use of the Bridgman method at a withdrawal rate of 3 mm/min. The crystallographic orientation of the rods was determined by the X-ray Ω-scan method with OD-EFG diffractometer and the Laue back-reflection technique. The creep tests were performed at a temperature of 982°C and the value of stress σ = 248 MPa. Microstructural investigation before and after the creep test of CMSX-4 superalloy was performed using a scanning electron microscope. The results showed that the distribution of the values of α angle strongly affects the creep resistance of a single-crystal superalloy
Źródło:
Advances in Manufacturing Science and Technology; 2020, 44, 3; 93-98
0137-4478
Pojawia się w:
Advances in Manufacturing Science and Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Temperature on the Plastic Deformability of Gas Atomized NdFeB Anisotropic Magnets
Autorzy:
Cho, Ju-Young
Choa, Yong-Ho
Nam, Sun-Woo
Rasheed, Mohammad Zarar
Kim, Taek-Soo
Powiązania:
https://bibliotekanauki.pl/articles/351923.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
NdFeB permanent magnet
stoichiometric composition
gas atomization
plastic deformability
crystal orientation
Opis:
NdFeB anisotropic sintered permanent magnets are typically fabricated by strip casting or melt spinning. In this study, the plastic deformability of an NdFeB alloy was investigated to study the possibility of fabricating anisotropic sintered magnets using gas atomized powders. The results show that the stoichiometric composition Nd12Fe82B6 softens at high temperatures. The aspect ratio and orientation factor of Nd12Fe82B6 billets after plastic deformation were found to increase with increasing plastic deformation temperature, particularly above 800°C. This confirms that softening at high temperatures can lead to plastic deformation of Nd2Fe14B hard magnetic phases.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 4; 1293-1296
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Powder Size on the Microstructure and Magnetic Properties of Nd-Fe-B Magnet Alloy
Autorzy:
Cho, Ju-Young
Abbas, Sardar Farhat
Choa, Yong-Ho
Kim, Taek-Soo
Powiązania:
https://bibliotekanauki.pl/articles/353634.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nd-Fe-B
gas atomization
powder size
crystal orientation
hot deformation
Opis:
Rare earth Nd-Fe-B, a widely used magnet composition, was synthesized in a shape of powders using gas atomization, a rapid solidification based process. The microstructure and properties were investigated in accordance with solidification rate and densification. Detailed microstructural characterization was performed by using scanning electron microscope (SEM) and the structural properties were measured by using X-ray diffraction. Iron in the form of α-Fe phase was observed in powder of about 30 μm. It was expected that fraction of Nd2 Fe14 B phase increased rapidly with decrease in powder size, on the other hand that of α-Fe phase was decreased. Nd-rich phase diffused from grain boundary to particle boundary after hot deformation due to capillary action. The coercivity of the alloy decreased with increase in powder size. After hot deformation, Nd2 Fe14 B phase tend to align to c-axis.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 2; 623-626
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies