Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Simulation Experiment" wg kryterium: Temat


Wyświetlanie 1-12 z 12
Tytuł:
Applied research of U-shape ventilation network in underground mine
Badania stosowane w sieci wentylacyjnej w kształcie „U” w kopalni podziemnej
Autorzy:
Zhang, H.
Pera, L. S.
Carla, V. S.
Zhao, Y.
Powiązania:
https://bibliotekanauki.pl/articles/219698.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
eksperyment symulacyjny
wentylacja kopalni
prędkość przepływu
podobieństwo dynamiczne
simulation experiment
mine ventilation
wind velocity
dynamic similarity
Opis:
For the purpose of fully and systematically observe, research and optimize the U-sharp ventilation system in Vilafruns mine, a simulation model based on the principles of geometric, kinematic and dynamic similarity is established in the simulation laboratory. By simulating a U-shape ventilation network, t he air volume distribution and wind velocity in different sections of the model were measured and compared with practical data obtained in Vilafruns mine. Results show that the lowest wind velocity in the model is higher than 0.42 m/s, thus it is in a turbulent f low state, which satisfies the kinematical and dynamic similarity principles. T he characteristic of air volume distribution and wind velocity in Vilafruns mine are basically simulated by the experimental model through the obtained data and figures, which reflects the establishment of the model is correct and successful, and the experimental data is accurate and reliable. Moreover, this model provides useful references for the selection of mine ventilation types and for the optimization of the existing ventilation network.
W celu prowadzenia pełnej i systematycznej obserwacji, badań oraz optymalizacji sieci wentylacyjnej w kopalni Vilafruns, opracowano model do symulacji laboratoryjnych w oparciu o zasady podobieństwa geometrycznego, kinematycznego oraz dynamicznego. W ramach symulacji działania sieci wentylacyjnej w kształcie litery U, dokonano pomiarów rozkładu objętości powietrza oraz prędkości ruchu powietrza w różnych sekcjach modelu. Dane te porównano następnie z danymi rzeczywistymi uzyskanymi w kopalni Vilafruns. Wyniki pokazują, że najniższa prędkość przepływu powietrza w modelu przewyższa 0.42 m/s, mamy więc do czynienia z przepływem turbulentnym, w ten sposób spełnione są warunki podobieństwa kinematycznego i dynamicznego. Charakterystyka rozkładu objętości powietrza i prędkości przepływu w kopalni Vilafruns zasadniczo otrzymana została na podstawie modelu eksperymentalnego z wykorzystaniem uzyskanych wyników. Oznacza to, że zasadniczo model jest poprawny i skuteczny a dane eksperymentalne są dokładne i wiarygodne. Ponadto, model dostarcza nam cennych danych wyjściowych niezbędnych przy wyborze systemu wentylacji, a także przy optymalizacji istniejącej sieci wentylacyjnej.
Źródło:
Archives of Mining Sciences; 2014, 59, 2; 381-394
0860-7001
Pojawia się w:
Archives of Mining Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research on the road linear optimization design of bridge and tunnel connecting segment in the canyon
Autorzy:
Wang, Lu
Liu, Yuwen
Chen, Xiaoxin
Powiązania:
https://bibliotekanauki.pl/articles/223553.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
traffic engineering
curved road
simulation experiment
radius of curve
bridge
tunnel
traffic safety
inżynieria ruchu
łuk drogi
eksperyment symulacyjny
promień łuku
most
tunel
bezpieczeństwo na drodze
Opis:
It is easy to skid and roll by centrifugal force and wind, which affects the safety of the vehicle. At the same time, the special location of bridge and tunnel connecting segment in the canyon will accelerate the wind, and make the transverse wind play a more important role in driving vehicles. Based on the acceleration effect of canyons on wind, the vehicle model is simulated by Carsim software, and the road and wind models are established. It is studied that the vehicle has different radius of circular curve under different wind levels, corresponding to different superelevation. The lateral acceleration, lateral deflection and transverse force coefficient are selected as the running state of the vehicle at different speeds to research the linear optimization design of bridge and tunnel connecting segment in the canyon. The result shows that when the wind force exceeds the fifth grade, it is possible for the vehicle to overturn under the limit minimum radius required by the standard value. In order to ensure the stability and safety of the vehicle, this paper considers the geographical position of bridge and tunnel connecting segment in the canyon and the relationship between the radius of the superelevation and circular curve. What’s more, it puts forward the optimal limit minimum radius of the circular curve with different wind grades of 5-9 grades. At the same time, when the road alignment cannot be optimized under the condition, this paper puts forward the speed limit that the vehicle safety can be guaranteed under different wind speed conditions. The speed limit can provide reference for traffic management and safety guarantee of mountain expressway.
Źródło:
Archives of Transport; 2019, 52, 4; 81-93
0866-9546
2300-8830
Pojawia się w:
Archives of Transport
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Material Model of the Polyurethane Elastomer on the FEM Calculations Quality for the Various Modes of Loading
Autorzy:
Kut, S.
Ryzińska, G.
Niedziałek, B.
Powiązania:
https://bibliotekanauki.pl/articles/352180.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
elastomers
material tests
material models
FEM simulation
experiment
Opis:
The paper presents research to verify the effectiveness of nine selected material models of elastomeric materials based on uniaxial tension test. Basing on the cyclic uniaxial tension test of elastomers sample, the stress-strain characteristic for the 18th load cycle was prepared. On the basis of the obtained characteristic, the values of material constants were calculated for the studied models (Neo-Hookean, Mooney with two and three constants, Signorini, Yeoh, Ogden, Arruda-Boyce, Gent and Marlow) and simulation of tensile, upsetting and bending processes was performed with the usage of the software MARC/Mentat. The effectiveness of the selected models was determined based on a comparison of results obtained in the experimental tensile test, upsetting test and bending test of an elastomeric samples with the results of numerical FEM calculations for each models. The research has shown that, for modeling of the elastomeric cylinder upsetting in the range of deformation of 62%, the best results with the comparison of the experiment were obtained by using the Yeoh model. In the bending process none of the analyzed models indicate a high convergence of results from an experiment. Analyzing the characteristics of the experimental and numerical tensile test it can be seen that in the entire range of punch movement (0 to 55 mm), models Signorini, Marlow, Ogden(N3) and Mooney(3) give the best results.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2A; 523-530
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigations on pool boiling of refrigerant R141b outside a horizontal tube
Autorzy:
Baki, Touhami
Aris, Abdelkader
Tebbal, Mohamed
Powiązania:
https://bibliotekanauki.pl/articles/1845055.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
horizontal tube
experiment
correlation
CHF
simulation
rura pozioma
eksperyment
korelacja
symulacja
Opis:
Boiling produces vapor with a phase change by absorbing a consistent amount of heat. Experimentation and modeling can help us better understand this phenomenon. The present study is focused on the heat transfer during the nucleate pool boiling of refrigerant R141b on the surface of a horizontal copper tube. The results of the experiment were compared with four correlations drawn from the literature, and the critical heat flux was examined for different pressures and also compared with the predicted values. Simulating boiling with two-phase models allowed us to infer the plot of the temperature distribution around the tube and compared it to results from other work.
Źródło:
Archive of Mechanical Engineering; 2021, LVIII, 1; 77-92
0004-0738
Pojawia się w:
Archive of Mechanical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Eksperyment, symulacja - techniki projektowe i wyzwania edukacyjne
Experiment, simulation - design techniques and educational challenges
Autorzy:
Słyk, J.
Powiązania:
https://bibliotekanauki.pl/articles/1366547.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
edukacja architektoniczna
symulacja
eksperyment
modelowanie parametryczne
architectural education
simulation
experiment
parametric modeling
Opis:
Architektura, dziedzina oparta na kanonie i proporcji, interpretuje rzeczywistość w sposób idealistyczny. Przenosi znaczenia i kody rozpoznawalne dzięki zanurzeniu w tradycji. Kształtuje uformowania przestrzenne odpowiadające konwencjom oraz sprawdzone w długotrwałych procesach użytkowania. Wychodząc z założeń anglosaskiego empiryzmu, artykuł stara się określić klasyczny eksperyment oraz zbadać, czy jest on efektywnym narzędziem architektury. Poszukuje odpowiedzi na pytanie, czy metoda doświadczalna wspomaga działania twórcze i czy proces ten zmienił się w kontekście upowszechnienia technologii informacyjnej. Tłem rozważań są przykłady współczesnych budowli oraz wybrane prace studenckie realizowane w ramach studiów ASK na Wydziale Architektury Politechniki Warszawskiej.
Architectural practice, based on canon and proportion, interprets reality in a idealistic way. Communicates meanings based on codes recognizable in the context of tradition. Shapes spatial forms - corresponding to conventions and proven in long-term processes of use. Based on the assumptions of Anglo-Saxon empiricism, the paper seeks to identify the classic experiment and examine if it is an effective tool of architecture. It looks for answers to the question of whether the experimental method supports the creative activities and whether this has changed in the context of information age. Case study contains examples of modern buildings and selected student works expressing ASK program specificity.
Źródło:
Kwartalnik Architektury i Urbanistyki; 2014, 59, 2; 11-24
0023-5865
Pojawia się w:
Kwartalnik Architektury i Urbanistyki
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Theoretical and experimental research of supersonic missile ballistics
Autorzy:
Zygmunt, B.
Motyl, K.
Machowski, B.
Makowski, M.
Olejniczak, E.
Powiązania:
https://bibliotekanauki.pl/articles/201046.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
missile exterior ballistics
mathematical model
computer simulation
test range experiment
pociski balistyczne
model matematyczny
symulacja komputerowa
Opis:
A mathematical-physical model of a supersonic missile was built, taking into account the mass and inertia properties. The model was implemented in the MathCAD14 simulation program. A numerical analysis of the missile ballistics was conducted and basic parameters were determined: range, altitude, velocity and acceleration, which enabled a test range program for manufactured missile models to be drawn up. Initial flight tests of missiles were carried out at the test range. Satisfactory accordance of experimental and theoretical dynamic parameters of the missile under study was obtained.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2015, 63, 1; 229-233
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experiments on the Model Testing of the 2nd Phase of Die Casting Process Compared with the Results of Numerical Simulation
Autorzy:
Dańko, R.
Dańko, J.
Stojek, J.
Powiązania:
https://bibliotekanauki.pl/articles/380288.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
die casting process
model testing
physical experiment
computer simulation
odlewanie ciśnieniowe
badanie modelowe
eksperyment fizyczny
symulacja komputerowa
Opis:
Experiments of filling the model moulds cavity of various inner shapes inserted in rectangular cavity of the casting die (dimensions: 280 mm (height) x 190 mm (width) x 10 mm (depth) by applying model liquids of various density and viscosity are presented in the paper. Influence of die venting as well as inlet system area and inlet velocity on the volumetric rate of filling of the model liquid – achieved by means of filming the process in the system of a cold-chamber casting die was tested. Experiments compared with the results of simulation performed by means of the calculation module Novacast (Novaflow&Solid) for the selected various casting conditions – are also presented in the paper.
Źródło:
Archives of Foundry Engineering; 2015, 15, 4; 21-24
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis Of The Extrusion Process Of A Square Tube Multi-Channel Heat Pipe
Analiza procesu wytłaczania wielokanałowych ciepłowodów o kwadratowym przekroju
Autorzy:
Kim, K. S.
Kim, J. Y.
Powiązania:
https://bibliotekanauki.pl/articles/353935.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminum hot extrusion
FE simulation
stress analysis
extrusion experiment
aluminium wytłaczane na gorąco
symulacja FE
analiza naprężeń
wytłaczanie
Opis:
Heat pipes have been recently in use for cooling purposes in various fields, including electronic circuit boards and vehicle parts that generate large amounts of heat. In order to minimize the loss of heat transferred, there is a need to maximize the contact area of the working fluid. This study produced a square tube multi-channel heat pipe to replace the existing circular pipe type to maximize the internal surface area thereof. This expands the surface, allowing the working fluid to come into contact with a wider area and enhancing thermal radiation performance. A mold for the production for such a product was designed, and finite element simulation was performed to determine whether production is possible.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1463-1466
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Operating characteristics of transcritical CO2 heat pump for simultaneous water cooling and heating
Autorzy:
Sarkar, J.
Bhattacharyya, S.
Powiązania:
https://bibliotekanauki.pl/articles/240930.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
charakterystyki pracy
eksperyment
pompa ciepła
symulacja
CO2 heat pump
experiment
performance characteristics
simulation
Water cooling and heating
Opis:
The effects of water-side operating conditions (mass flow rates and inlet temperatures) of both evaporator and gas cooler on the experimental as well as simulated performances (cooling and heating capacities, system coefficient of performance (COP) and water outlet temperatures) of the transcritical CO2 heat pump for simultaneous water cooling and heating the are studied and revised. Study shows that both the water mass flow rate and inlet temperature have significant effect on the system performances. Test results show that the effect of evaporator water mass flow rate on the system performances and water outlet temperatures is more pronounced (COP increases by 0.6 for 1 kg/min) compared to that of gas cooler water mass flow rate (COP increases by 0.4 for 1 kg/min) and the effect of gas cooler water inlet temperature is more significant (COP decreases by 0.48 for given range) compared to that of evaporator water inlet temperature (COP increases by 0.43 for given range). Comparisons of experimental values with simulated results show the maximum deviation of 5% for cooling capacity, 10% for heating capacity and 16% for system COP.
Źródło:
Archives of Thermodynamics; 2012, 33, 4; 23-40
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Verification of a numerical simulation code for underwater chain moor
Weryfikacja oprogramowania do symulacji podwodnego cumowania łańcuchowego
Autorzy:
Zhu, X.
Yoo, W.
Powiązania:
https://bibliotekanauki.pl/articles/139728.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
underwater chain mooring
verification of a numerical simulation accuracy
real experiment
numerical simulation code
podwodne cumowanie łańcuchowe
weryfikacja dokładności symulacji numerycznej
eksperyment w warunkach rzeczywistych
kod symulacji numerycznej
Opis:
Numerical simulation is an economical and effective method in the field of marine engineering. The dynamics of mooring cables has been analysed by a numerical simulation code that was created on a basis of a new element frame. This paper aims at verifying the accuracy of the numerical simulation code through comparisons with both the real experiments and a commercial simulation code. The real experiments are carried out with a catenary chain mooring in a water tank. The experimental results match the simulation results by the numerical simulation code well. Additionally, a virtual simulation of a large size chain mooring in ocean is carried out by both the numerical simulation code and a commercial simulation code. The simulation results by the numerical simulation code match those by the commercial simulation code well. Thus, the accuracy of the numerical simulation code for underwater chain mooring is verified by both the real experiments and commercial simulation code.
Symulacja numeryczna jest ekonomiczną i efektywną metodą w dziedzinie inżynierii okrętowej. Dynamikę lin cumowniczych analizowano numerycznie przy pomocy oprogramowania symulacyjnego stworzonego na podstawie nowego opisu elementu. Celem pracy była weryfikacja dokładności symulacji numerycznej przez porównanie z eksperymentami w warunkach rzeczywistych i z komercyjnym oprogramowaniem symulacyjnym. Eksperymenty prowadzono w cysternie z wodą, z użyciem cum łańcuchowych. Wyniki eksperymentów zgadzają się dobrze z wynikami symulacji numerycznej. Dodatkowo, wykonano wirtualną symulację cumowania oceanicznego na długiej cumie łańcuchowej stosując własny program symulacyjny i oprogramowanie komercyjne. Uzyskano dobrą zgodność wyników obydwu symulacji. Tak więc, dokładność opracowanego programu do symulacji podwodnego cumowania łańcuchowego została zweryfikowana zarówno na drodze doświadczalnej, jak i przez porównanie z oprogramowaniem komercyjnym.
Źródło:
Archive of Mechanical Engineering; 2016, LXIII, 2; 231-244
0004-0738
Pojawia się w:
Archive of Mechanical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Multi-objective optimization of stope structure parameters in broken rock conditions using grey relational analysis
Wielo-kryterialna optymalizacja parametrów struktury przodka wybierkowego w warunkach pękania skał przy wykorzystaniu „szarej” analizy relacyjnej
Autorzy:
Chen, S.
Wu, A.
Wang, Y.
Cheng, X.
Powiązania:
https://bibliotekanauki.pl/articles/219180.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
szara analiza relacyjna
parametry struktury przodka wybierkowego
pękanie skał
symulacje numeryczne
model Taguchi projektowania eksperymentu
grey relational analysis
stope structure parameters
in broken rock conditions
numerical simulation
taguchi experiment design
Opis:
In order to optimize the stope structure parameters in broken rock conditions, a novel method for the optimization of stope structure parameters is described. The method is based on the field investigation, laboratory tests and numerical simulation. The grey relational analysis (GRA) is applied to the optimization of the stope structure parameters in broken rock conditions with multiple performance characteristics. The influencing factors include stope height, pillar diameter, pillar spacing and pillar array pitch, the performance characteristics include maximum tensile strength, maximum compressive strength and ore recovery rate. The setting of influencing factors is accomplished using the four factors four levels Taguchi experiment design method, and 16 experiments are done by numerical simulation. Analysis of the grey relational grade indicates the first effect value of 0.219 is the pillar array pitch. In addition, the optimal stope structure parameters are as follows: the height of the stope is 3.5 m, the pillar diameter is 3.5 m, the pillar spacing is 3 m and the pillar array pitch is 5 m. In-situ measurement shows that all of the pillars can basically remain stable, ore recovery rate can be ensured to be more than 82%. This study indicates that the GRA method can efficiently applied to the optimization of stope structure parameters.
W pracy zaproponowano nową metodę optymalizacji parametrów struktury przodka wybierkowego prowadzonego w warunkach pękania skał. Metoda opiera się na badaniach terenowych, wykorzystuje także badania laboratoryjne oraz symulacje numeryczne. Do optymalizacji parametrów struktury przodka wybierkowego prowadzonego w warunkach pękania skał dla wielu wariantów charakterystyki górotworu wykorzystano ‘szarą’ analizę relacyjną (GRA – Grey Relational Analysis). Uwzględnione czynniki wpływu to wysokość przodka, średnica filarów, rozstaw filarów, rozmieszczenie filarów oraz charakterystyki górotworu: maksymalna wytrzymałość na rozciąganie oraz ściskanie oraz uzysk rudy. Ustawienia czynników wpływu dokonano z wykorzystaniem czterech czynników i dla czterech poziomów wg metody Taguchi planowania eksperymentów; ponadto 16 eksperymentów wykonano z wykorzystaniem symulacji numerycznych. Wyniki ‘szarej’ analiza relacyjnej wskazują, że wartość efektywna dla pierwszego z czynników, czyli rozmieszczenia filarów, wyniosła 0.219. Ponadto, otrzymano następujące optymalne parametry przodka: wysokość przodka 3.5 m; średnica filarów 3.5 m, rozstęp pomiędzy filarami 3 m, rozciągłość filarów 5 m. Pomiary przeprowadzone in situ wykazały, że wszystkie filary zasadniczo powinny zachować stabilność, a uzysk rudy przekroczyć może 82%. Wyniki wskazują, że ‘szara’ analiza relacyjna może być z powodzeniem wykorzystywana do optymalizacji parametrów struktury przodka wybierkowego.
Źródło:
Archives of Mining Sciences; 2018, 63, 2; 269-282
0860-7001
Pojawia się w:
Archives of Mining Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improving the procedure of probabilistic load testing design of typical bridges based on structural response similarities
Wzbogacenie procedury probabilistycznego projektowania próbnego obciążenia mostów typowych na podstawie cech wspólnych mechanicznej odpowiedzi konstrukcji
Autorzy:
Owerko, P.
Winkelmann, K.
Powiązania:
https://bibliotekanauki.pl/articles/1849805.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
obciążenie próbne
most
imperfekcja
niepewność
analiza wrażliwości
analiza probabilistyczna
metoda powierzchni odpowiedzi
symulacja Monte Carlo
metoda elementów skończonych
MES
projektowanie eksperymentu
bridge
in-situ test
load testing
imperfection
uncertainty
sensitivity analysis
probability analysis
response surface method
Monte Carlo simulation
finite element model
FEM
experiment design
Opis:
This paper concerns load testing of typical bridge structures performed prior to operation. In-situ tests of a two-span post-tensioned bridge loaded with three vehicles of 38-ton mass each formed the input of this study. On the basis of the results of these measurements an advanced FEM model of the structure was developed for which the sensitivity analysis was performed for chosen uncertainty sources. Three uncorrelated random variables representing material uncertainties, imperfections of positioning and total mass of loading vehicles were indicated. Afterwards, two alternative FE models were created based on a fully parametrised geometry of the bridge, differing by a chosen global parameter – the skew angle of the structure. All three solid models were subjected to probabilistic analyses with the use of second-order Response Surface Method in order to define the features of structural response of the models. It was observed that both the ranges of expected deflections and their corresponding mean values decreased with an increase of the skewness of the bridge models. Meanwhile, the coefficient of variation and relative difference between the mean value and boundary quantiles of the ranges remain insensitive to the changes in the skew angle. Owing to this, a procedure was formulated to simplify the process of load testing design of typical bridges differing by a chosen global parameter. The procedure allows - if certain conditions are fulfilled - to perform probabilistic calculations only once and use the indicated probabilistic parameters in the design of other bridges for which calculations can be performed deterministically.
Pracę otwiera przegląd najnowszej literatury fachowej o zasięgu międzynarodowym, dotyczącej próbnych obciążeń obiektów mostowych. W licznych publikacjach badawczych jednoznacznie stwierdzono, iż zasadne jest, by często stosowane w tym zakresie metody deterministyczne uzupełniać lub zastępować analizami probabilistycznymi. Niniejsza praca stanowi zatem rozwinięcie dotychczasowych osiągnięć i spostrzeżeń. Przedmiotem pracy jest analiza możliwości zwiększenia efektywności procesu przygotowania probabilistycznych projektów próbnych obciążeń typowych konstrukcji mostowych, różniących się wybranym parametrem geometrycznym (w tym przypadku – kątem ukosu konstrukcji „α”) przed ich dopuszczeniem do eksploatacji w zakresie pomiarów statycznych. Punktem wyjściowym przedstawionej analizy jest próbne obciążenie in-situ typowego, drogowego mostu sprężonego. Jednym z podstawowych kryteriów dopuszczenia obiektu mostowego do użytkowania w niektórych krajach, jest wykazanie, iż ugięcia dźwigarów głównych obiektu mostowego wywołane statycznym obciążeniem próbnym są mniejsze niż te określone teoretycznie w modelu MES obiektu. W pierwszej kolejności zatem, wyniki pochodzące z rzeczywistych badań próbnego obciążenia zostały zestawione z ich teoretycznymi odpowiednikami, pochodzącymi z prostego modelu rusztowego mostu. Ten przykład ogranicza się do analizy maksymalnych ugięć jednego z dźwigarów głównych obiektu. Wykazano, iż ugięcia z pomiarów in-situ (pomierzone przemieszczenia zostały odpowiednio przeliczone na ugięcia, aby uwzględnić wpływ osiadania podpór i zgniotów łożysk) były mniejsze niż te określone teoretycznie. Nie było zatem podstaw do niedopuszczenia mostu do użytkowania ze względu na niespełnienie kryterium ugięć. Jednakże, w rezultacie analizy wykazano, iż wyniki odpowiedzi konstrukcji z prostego modelu deterministycznego różniły się znacznie od wyników pomiarów. W związku z tym, w celu opracowania procedury zwiększenia efektywności procesu przygotowywania probabilistycznych projektów próbnych obciążeń obiektów typowych, do dalszych analiz porównawczych i probabilistycznych wygenerowany został znacząco bardziej zaawansowany model bryłowy MES.
Źródło:
Archives of Civil Engineering; 2020, 66, 4; 325-342
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-12 z 12

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies