Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "footing" wg kryterium: Temat


Wyświetlanie 1-6 z 6
Tytuł:
Experimental bearing capacity of eccentrically loaded foundation near a slope
Autorzy:
Mansouri, Tarek
Abbeche, Khelifa
Powiązania:
https://bibliotekanauki.pl/articles/178276.pdf
Data publikacji:
2019
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
square footing
bearing capacity
slope
relative density
eccentric load
Opis:
Based on the response of small-scale model square footing, the present paper shows the results of an experimental bearing capacity of eccentrically loaded square footing, near a slope sand bed. To reach this aim, a steel model square footing of (150 mm × 150 mm) and a varied sand relative density of 30%, 50% and 70% are used. The bearing capacity-settlement relationship of footing located at the edge of a slope and the effect of various parameters such as eccentricity (e) and dimensions report (b/B) were studied. Test results indicate that ultimate bearing capacity decreases with increasing load eccentricity to the core boundary of footing and that as far as the footing is distant from the crest, the bearing capacity increases. Furthermore, the results also prove that there is a clear proportional relation between relative densities –bearing capacity. The model test provides qualitative information on parameters influencing the bearing capacity of square footing. These tests can be used to check the bearing capacity estimated by the conventional methods.
Źródło:
Studia Geotechnica et Mechanica; 2019, 41, 1; 33-41
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effective width rule in the analysis of footing on reinforced sand slope
Autorzy:
Abdi, Abdelmadjid
Abbeche, Khelifa
Athmania, Djamel
Bouassida, Mounir
Powiązania:
https://bibliotekanauki.pl/articles/178217.pdf
Data publikacji:
2019
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
bearing capacity
eccentricity
footing
geogrid
model test
slope
Opis:
This paper presents the results obtained from an experimental programme and numerical investigations conducted on model tests of strip footing resting on reinforced and unreinforced sand slopes. The study focused on the determination of ultimate bearing capacity of strip footing subjected to eccentric load located either towards or opposite to the slope facing. Strip footing models were tested under different eccentricities of vertical load. The obtained results from tests conducted on unreinforced sand slope showed that the increase in eccentricity of applied load towards the slope facing decreases the ultimate bearing capacity of footing. Predictions of the ultimate bearing capacity obtained by the effective width rule are in good agreement with those proposed from the consideration of total width of footing subjected to eccentric load. The ultimate bearing capacity of an eccentrically loaded footing on a reinforced sand slope can be derived from that of axially loaded footing resting on horizontal sand ground when adopting the effective width rule and the coefficient of reduction due to the slope. When increasing the distance between the footing border to the slope crest, for unreinforced and reinforced ground slope by geogrids, the ultimate bearing capacity of footing is no more affected by the slope ground.
Źródło:
Studia Geotechnica et Mechanica; 2019, 41, 1; 42-55
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Behaviour of eccentrically inclined loaded rectangular foundation on reinforced sand
Autorzy:
Gupta, Sujata
Mital, Anupam
Powiązania:
https://bibliotekanauki.pl/articles/1845170.pdf
Data publikacji:
2021
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
eccentric loading
load inclination
ultimate bearing capacity
UBC
rectangular footing
geogrid
Opis:
This study presents the behaviour of model footing resting over unreinforced and reinforced sand bed under different loading conditions carried out experimentally. The parameters investigated in this study includes the number of reinforced layers (N = 0, 1, 2, 3, 4), embedment ratio (Df/B = 0, 0.5, 1.0), eccentric and inclined ratio (e/L, e/B = 0, 0.05, 0.10, 0.15) and (a = 0°, 7°, 14°). The test sand was reinforced with bi-axial geogrid (Bx20/20). The test results show that the ultimate bearing capacities decrease with axial eccentricity and inclination of applied loads. The test results also show that the depth of model footing increase zero to B (B = width of model footing), an increase of ultimate bearing capacity (UBC) approximated at 93%. Similarly, the multi-layered geogrid reinforced sand (N = 0 to 4) increases the UBC by about 75%. The bearing capacity ratio (BCR) of the model footing increases with an increasing load eccentricity to the core boundary of footing; if the load eccentricities increase continuity, the BCR decreases. The tilt of the model footing is increased by increasing the eccentricity and decreases with increasing the number of reinforcing layers.
Źródło:
Studia Geotechnica et Mechanica; 2021, 43, 2; 74-89
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Behavior of Vertically Confined Square Footing on Reinforced Sand under Centric Inclined Loading
Autorzy:
Kirtimayee, B.
Samadhiya, Narendra Kumar
Powiązania:
https://bibliotekanauki.pl/articles/2172877.pdf
Data publikacji:
2022
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
centric inclined loading
load intensity
settlement
geogrid
sand
square footing
Opis:
This study presents the behavior of vertically confined square footing on geogrid-reinforced sand under centric inclined loading through a series of experimental tests. The load was applied at 5°, 10° and 20° angles of inclination with the vertical. The tests were conducted on surface footing, footing with confiner and footing with confiner and horizontal reinforcement configurations subjected to inclined loading. Parametric variations like depth of the confiner (d=1B, 1.5B, 2B), number of geogrid layers (N; varies with variation in depth of confiner), and spacing between horizontal reinforcements (Y=0.25B, 0.5B, 0.75B, 1B) have been investigated at the top surface dimension of confiner (D) as 1.0B, 1.5B and 2.0B (where B is the width of the model footing). Results show that combined effect of confiner and horizontal reinforcement increases the ultimate bearing capacity of footing significantly compared to only confiner for all angle of inclinations. It can also be observed that load bearing capacities decrease with increase in angles of inclination and record the minimum improvement at 20° angle of inclination. Improvement in bearing capacities and reduction in settlement of footing analyzed in terms of bearing capacity ratio (BCR) and settlement reduction factor (SRF) are compared for all footing configurations. To summarize, the test results showed that confiner along with reinforcement can be considered as an economic ground improvement technique for shallow foundations to counter against heavily inclined loading.
Źródło:
Studia Geotechnica et Mechanica; 2022, 44, 3; 224--238
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Random analysis of bearing capacity of square footing using the LAS procedure
Autorzy:
Kawa, M.
Puła, W.
Suska, M.
Powiązania:
https://bibliotekanauki.pl/articles/178223.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
LAS procedure
Local Average Subdivision
random fields theory
square footing
reliability analysis
Opis:
In the present paper, a three-dimensional problem of bearing capacity of square footing on random soil medium is analyzed. The random fields of strength parameters c and φ are generated using LAS procedure (Local Average Subdivision, Fenton and Vanmarcke 1990). The procedure used is re-implemented by the authors in Mathematica environment in order to combine it with commercial program. Since the procedure is still tested the random filed has been assumed as one-dimensional: the strength properties of soil are random in vertical direction only. Individual realizations of bearing capacity boundary-problem with strength parameters of medium defined the above procedure are solved using FLAC3D Software. The analysis is performed for two qualitatively different cases, namely for the purely cohesive and cohesive-frictional soils. For the latter case the friction angle and cohesion have been assumed as independent random variables. For these two cases the random square footing bearing capacity results have been obtained for the range of fluctuation scales from 0.5 m to 10 m. Each time 1000 Monte Carlo realizations have been performed. The obtained results allow not only the mean and variance but also the probability density function to be estimated. An example of application of this function for reliability calculation has been presented in the final part of the paper.
Źródło:
Studia Geotechnica et Mechanica; 2016, 38, 3; 3-13
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Reliability analysis of bearing capacity of square footing on soil with strength anisotropy due to layered microstructure
Autorzy:
Kawa, M.
Powiązania:
https://bibliotekanauki.pl/articles/178907.pdf
Data publikacji:
2015
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
layered microstructure
square footing
strength anisotropy
reliability analysis
probability of failure
factor of safety
Opis:
The paper deals with reliability analysis of square footing on soil with strength anisotropy. The strength of the soil has been described with identified anisotropic strength criterion dedicated to geomaterials with layered microstructure. The analysis assumes dip angle α and azimuth angle β which define direction of lamination of the structure to be random variables with given probability density functions. Bearing capacity being a function of these variables is approximated based on results of deterministic simulations obtained for variety of orientations. The weighted regression method by Kaymaz and McMahon within the framework of Response Surface Method is used for the approximation. As a result of analysis, global factor of safety that corresponds to assumed value of probability of failure is determined. The value of the safety factor denotes the ratio between the value of the design load and the mean value of bearing capacity which is needed to reduce the probability of failure to the acceptable level. The procedure of calculating the factor has been presented for two different cases. In the first case, no information about lamination direction of the soil has been provided and thus all the orientations are assumed to be equally probable (uniform distribution). In the second case, statistical information including mean, variance and assumed probability distribution for both α and β angle is known. For the latter case, using results obtained for few different values of mean of angle α, also the influence of strength anisotropy on the value of global factor of safety is shown.
Źródło:
Studia Geotechnica et Mechanica; 2015, 37, 4; 19-28
0137-6365
2083-831X
Pojawia się w:
Studia Geotechnica et Mechanica
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-6 z 6

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies