Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Li, L." wg kryterium: Autor


Tytuł:
Flotation of molybdenite in the presence of microemulsified collector
Autorzy:
You, X.
Li, L.
Lyu, X.
Powiązania:
https://bibliotekanauki.pl/articles/109765.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
molybdenite
flotation
microemulsified collector
diesel
Opis:
In this paper molybdenite flotation using microemulsified collector was reported. The flotation performance of microemulsified collector and conventional diesel was compared. This study is a prelimi-nary investigation which uses pure molybdenite mineral in a modified Hallimond tube. The pH tests showed that the highest recovery of molybdenite in the presence of diesel and microemulsion was ob-tained at pH=6, reaching the recoveries of 93% and 90%, respectively. In the case of obtaining similar results, it was observed that the microemulsion consumption was lower in comparison to diesel. In the flotation tests with microemulsified collector the recovery slightly decreased because too large collector amount caused formation of more unstable bubbles. The contact angle measurements showed that the microemulsified collector was more effective for increasing the hydrophobicity of molybdenite surface. An adsorption model was proposed and it was suggested that the non-ionic surfactant present in the mi-croemulsified collector formed a continuous bimolecular layer, resulting in the increased surface hydro-phobicity. The accomplishment of this research demonstrated the viability of the use of microemulsified collector in molybdenite flotation, attempting to simplify the molybdenite flotation process, especially replace the conventional emulsified collector with high energy consumption and difficult storage.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 1; 333-341
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A novel method to extract vanadium from vanadium-bearing steel slag using sodium carbonate solution
Autorzy:
Gao, M.
Xue, X.
Li, L.
Yang, H.
Bai, R.
Wang, H.
Powiązania:
https://bibliotekanauki.pl/articles/109859.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
leaching
kinetics
vanadium
vanadium-bearing steel slag
Opis:
A new method using sodium carbonate solution to treat a vanadium-bearing steel slag is proposed. The effects of the particle size, solid-to-liquid ratio, initial concentration of sodium carbonate solution, leaching temperature and stirring speed on the leaching rate of vanadium were investigated. The leaching kinetics of vanadium from the vanadium-bearing steel slag was studied, which indicated that the leaching rate was controlled by the step of diffusion through the solid layer around the unreacted core. The apparent activation energy for the process was 13.75 kJ/mol. By using this process, vanadium could be extracted effectively with the leaching rate of more than 80%.
Źródło:
Physicochemical Problems of Mineral Processing; 2018, 54, 3; 911-921
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Selective agglomeration of magnetite in entlandite-serpentine system and implication for their separation
Autorzy:
Lu, J.
Yuan, Z.
Liu, J.
Li, L.
Wang, N.
Meng, Q.
Powiązania:
https://bibliotekanauki.pl/articles/110411.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
serpentine
pentlandite
magnetite
selective magnetic agglomeration
magnetic separation
Opis:
In nickel sulfide processing, magnesium silicates (serpentines) can easily form slime coatings or hetero-aggregation on pentlandite surfaces, and hence decrease the pentlandite flotation rate and recovery. In this work, magnetic separation of pentlandite from serpentine using selective magnetic coating through adding magnetite fines as magnetic seeds was investigated. Interactions of magnetite-pentlandite and magnetite-serpentine were calculated by the DLVO (Derjaguin-Landau-Verwey-Overbeek) theory. The results show that the interaction of magnetite-pentlandite was obviously stronger than that of magnetite-serpentine with an external weak magnetic field (4776 A/m-1). Therefore, fine magnetite fractions selectively adhered to the pentlandite surfaces and enhanced its magnetism, resulting in being separated from serpentine by magnetic separation, which was further verified by magnetic coating-magnetic separation and SEM observations.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 2; 943-955
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dispersion-compensating en/decoder for a time-spreading/wavelength-hopping optical code-division multiplexing (OCDM) system
Autorzy:
Zheng, J.
Wang, R.
Pu, T.
Lu, L.
Fang, T.
Su, Y.
Li, L.
Yang, Q.
Chen, X.
Powiązania:
https://bibliotekanauki.pl/articles/174365.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
optical code-division multiplexing (OCDM)
fiber Bragg grating (FBG)
dispersion
Opis:
A novel dispersion-compensating fiber Bragg grating (FBG)-based en/decoder is proposed to compensate both the out-band and in-band dispersion in a time-spreading/wavelength-hopping (TS/WH) optical code-division multiplexing (OCDM) system. The experimental realization of such en/decoders only needs a uniform-pitch phase mask and a sub-micrometer precision moving stage. Such an en/decoder pair with the ability of compensating the dispersion of transmission in 20-km single mode fiber (SMF) is simulated and experimentally fabricated. Both the simulation and experimental results show that the decoded pulse can be recovered without any distortion owing to the elimination of dispersion.
Źródło:
Optica Applicata; 2013, 43, 3; 485-495
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Flotation separation of wolframite from quartz using N-oleoyl sarcosine acid as collector
Autorzy:
Xian-Ping, L.
Feng, B.
Xianwen, Z.
Li-Yying, L.
Zheng-He, X.
Powiązania:
https://bibliotekanauki.pl/articles/109444.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
flotation
N-oleoyl sarcosine acid
wolframite
quartz
Opis:
In this study the collecting power of N-oleoyl sarcosine acid towards wolframite and quartz was studied using flotation. The adsorption mechanism was also discussed based on the results from adsorption experiments, zeta potential measurements and infrared spectroscopy study. The flotation results showed that N-oleoyl sarcosine acid showed a good collecting power towards wolframite, and the optimal flotation pH = 7 was obtained. However, the collecting power of N-oleoyl sarcosine acid towards quartz was weak. Therefore, the flotation separation of wolframite from quartz can be performed using N-oleoyl sarcosine acid as a collector. The adsorption tests and electrokinetic studies showed that N-oleoyl sarcosine acid adsorbed only on the wolframite surface. Additionally, the results from the infrared spectroscopy study confirmed that N-oleoyl sarcosine acid is adsorbed on the wolframite surface, and the metal complex (ferriccarboxylate) maybe the major adsorbed species.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 1; 34-41
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Four stage hybrid constructed wetlands treating low-strength aquaculture wastewater with and without artificial aeration
Autorzy:
Zhang, S.-Y.
Li, G.
Li, X.
Tao, L.
Powiązania:
https://bibliotekanauki.pl/articles/207748.pdf
Data publikacji:
2015
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
wastewater treatment
aquaculture
water pollution
wetlands
aquaculture wastewater
artificial aeration
oczyszczanie ścieków
akwakultura
zanieczyszczenie wody
mokradła
sztuczne napowietrzanie
tereny podmokłe
Opis:
Driven by the booming demands for healthy food, aquaculture industry has to deal with the problem of water pollution appropriately so as to achieve sustainable development. In this study, a combination of four stage CWs (three horizontal subsurface flows followed by one free water surface flow) was configured to treat low-strength aquaculture wastewater. For performance assessment, the wetlands were monitored over three years, during which artificial aeration was added to them. By the results, the organic matters and nutrients were mainly sequestered in the anterior subsurface flows, while the surface flow mainly contributed to DO improvement. These results probably implied no necessity of excessive subsurface flows connected in a staged manner. In addition, the artificial aeration improved the treatment performance on ammonium-N, TN and TP in the first-stage CW.
Źródło:
Environment Protection Engineering; 2015, 41, 3; 31-42
0324-8828
Pojawia się w:
Environment Protection Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on self-repairing and non-diffraction of Airy beams in slant atmospheric turbulence
Autorzy:
Li, Y.-Q.
Wang, L.-G.
Powiązania:
https://bibliotekanauki.pl/articles/174867.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
atmospheric turbulence
Airy beam
self-repairing
non-diffraction
numerical simulation
Opis:
The Airy beams propagation in atmospheric turbulence along a slant path was simulated numerically, based on the split-step Fourier method. Also, the self-repairing and non-diffraction characteristics of Airy beams were investigated and compared with beams propagation on a horizontal path. The effects of parameters including zenith angle, propagation distance, radii of Gaussian aperture and turbulence intensity on the two characteristics of beams were revealed. Additionally, the two characteristics of the Airy beam were compared with those of a Bessel–Gauss beam. The results showed that the two beams obscured by Gaussian apertures can be repaired after propagating some distance along a slant path. However, the non-diffraction characteristic of an Airy beam was stronger than that of a Bessel–Gauss beam and the amplitude attenuation rate of the Bessel–Gauss beam was greater than that of the Airy beam in the process of self-repairing. Results obtained can provide a theoretical basis for an outdoor experiment as well as theoretical guidance for various practical applications including laser communications, laser warning systems, and remote sensing.
Źródło:
Optica Applicata; 2018, 48, 3; 435-447
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of grinding characteristics in high-pressure grinding roller (HPGR) and cone crusher (CC)
Autorzy:
Liu, L.
Tan, Q.
Li, W.
Lv, L.
Powiązania:
https://bibliotekanauki.pl/articles/951829.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
HPGR
grinding kinetics
grinding technical efficiency
ultra-crushing
classified grinding
Opis:
We comparatively studied the ball mill grinding characteristics of comminuted hematite products using a high-pressure grinding roll (HPGR) and a conventional cone crusher (CC). The major properties, including grinding kinetics and technical efficiency (Et), were investigated. The parameters in m-th order grinding kinetics were analyzed, and grinding specific rates were visualized. Ore particles experienced three inherent stages in ball grinding mills, that is i) rapid grinding of coarse fraction, ii) dynamic grinding of medium size fraction, and iii) single grinding of medium size fraction. Particles with size -0.043+0.031 mm were used into dynamic grinding stage earlier than particles -0.105+0.043 mm, and then over-grinding of fines occurred easily. Compared with CC products, HPGR products had significantly shorter turning time points in three breakage stages, implying that HPGR products were ground faster with earlier occurrence of fines over-grinding. HPGR products gave lower Et at a decreasing rate than the CC products for -2.0 mm and -0.5 mm feeds. Then, it showed a slightly higher value of Et for -2.0+0.5 mm feed. This indicated that fines over-grinding in HPGR full-size products were more serious under the condition of coarse grinding, whereas the efficiency was higher, and over-grinding weakened significantly in HPGR coarse products because of screening-out fines.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 2; 1009-1022
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Three-port beam splitter based on a sandwiched grating with an improved aspect ratio
Autorzy:
Shu, W
Wang, B
Li, H
Li, W
Chen, L.
Lei, L.
Zhou, J.
Powiązania:
https://bibliotekanauki.pl/articles/174445.pdf
Data publikacji:
2015
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
aspect ratio
sandwiched grating
three-port beam splitter
Opis:
In this paper, a fused-silica transmission grating used as a three-port beam splitter is designed by using the rigorous coupled-wave analysis, which is based on the sandwiched grating structure at the wavelength of 800 nm under normal incidence. Firstly, it is feasible to realize such a grating with the prescribed grating duty cycle and grating period. Next, high efficiency can be also achieved for both TE and TM polarizations. Moreover, the aspect ratio of the grating depth to the ridge width can be improved, which is significant for practical applications. At last, the three-port beam splitter is designed with a covering layer on the surface, which can extend its life service.
Źródło:
Optica Applicata; 2015, 45, 3; 279-284
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Polarization-independent metal-dielectric grating with improved bandwidth
Autorzy:
Wang, B
Li, H
Shu, W
Li, W
Li, C
Lei, L
Zhou, J
Powiązania:
https://bibliotekanauki.pl/articles/174684.pdf
Data publikacji:
2015
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
rigorous coupled-wave analysis
reflective efficiency
improved bandwidth
Opis:
A polarization-independent reflective grating with improved bandwidth is presented based on the mixed metal-dielectric grating. The novel grating is composed of the substrate, the metal slab, two dielectric layers, and the covering layer. The grating parameters are optimized for the special duty cycle of 0.6 at an incident wavelength of 1550 nm used in dense wavelength division multiplexing (DWDM). With the designed grating, high efficiency can be diffracted into the reflective –1st order for both TE and TM polarizations, where the polarization-independence is exhibited. Most importantly, the efficiency of more than 90% can be achieved within the incident wavelength bandwidth of 1262–1686 nm, where the bandwidth is improved greatly compared with the reported surface-relief single-layer grating. The reflective grating can have advantages of high efficiency, polarization-independence, and wide bandwidth, which should be useful for DWDM applications.
Źródło:
Optica Applicata; 2015, 45, 1; 71-77
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Biomechanical and fluid flowing characteristics of intervertebral disc of lumbar spine predicted by poroelastic finite element method
Autorzy:
Guo, L.-X
Li, R.
Zhang, M.
Powiązania:
https://bibliotekanauki.pl/articles/307246.pdf
Data publikacji:
2016
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
kręgosłup lędźwiowy
poroelastyczność
FEM
lumbar spine
poroelastic finite element model
intermittent compressive load
permeability of cartilage endplate
Opis:
Purpose: This study is to reveal the deformation of intervertebral disc (IVD), the stress distribution of solid phase and liquid phase, the variation of fluid flux and flow velocity in lumbar spine and the influence of different permeability parameters on them under intermittent compressive loading. Methods: A poroelastic FEM of L4-L5 is assigned with different permeability parameters to analyze the deformation, stress distribution and fluid convection under intermittent compressive loads. Results: The results show that the pore pressure of IVD decreases with time, but the effective stress increases under intermittent compressive loads. The axial and radial strain will increase and fluid loss will recover at a more rapid rate if the permeability of endplate increases during unloading period. The velocity vectors show that most of the liquid in the disc flows into vertebrae through endplates and only a small quantity of liquid flows through the annulus fibrosus at the loading step, however, at the unloading step, almost all the liquid flowing into IVD is through the endplates. Conclusions: The changing rate of pore pressure and effective stresses of nucleus pulposus and annulus fibrosus with higher permeability is smaller than that with smaller permeability. The degenerated endplate (with low permeability) yields high flow velocity decreasing gradient, which might impede liquid inflowing/outflowing smoothly through the endplates. The fluid flowing velocity in loading phase is faster than that in unloading phase, so a short resting time can relieve fatigue, but could not recover to the original liquid condition in IVDs.
Źródło:
Acta of Bioengineering and Biomechanics; 2016, 18, 2; 19-29
1509-409X
2450-6303
Pojawia się w:
Acta of Bioengineering and Biomechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Quartz enhanced photoacoustic spectroscopy based on an external cavity quantum cascade laser
Autorzy:
Xu, L.
Zhou, S.
He, T.
Li, J.
Powiązania:
https://bibliotekanauki.pl/articles/173669.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
external cavity quantum cascade laser
ECQCL
quartz enhanced photoacoustic spectroscopy
QEPAS
volatile organic compound
VOC
ethanol
Opis:
Mid-infrared laser spectroscopy is a powerful analytical tool for trace gases detection. In this study, a spectroscopic system based on an external cavity quantum cascade laser (ECQCL) and quartz enhanced photoacoustic spectroscopy (QEPAS) was developed for volatile organic compounds (VOCs) measurements. Primary laboratory test on ethanol spectroscopy was investigated and compared with traditional direct absorption spectroscopy (DAS). Experimental results show that the proposed QEPAS is more sensitive than the conventional DAS method. In addition, the significant linear dependence of photoacoustic signal on sample pressures and laser operating parameters was observed.
Źródło:
Optica Applicata; 2018, 48, 4; 687-695
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Flotation behavior of nickel sulfide ore in a cyclonic flotation column
Autorzy:
Deng, L.
Li, G.
Cao, Y.
Ma, Z.
Powiązania:
https://bibliotekanauki.pl/articles/109906.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
cyclonic flotation column
floatability
flotation
nickel sulfide ore
Opis:
This study aimed to show the flotation behavior of a nickel sulfide ore in a cyclonic flotation column. The flotation experiments were carried out using a sample of nickel sulfide ore obtained from a mineral processing plant of China. Representative samples collected from the feed, concentrate, tailing, and circulation middling were sieved using a cyclonic particle analyzer to collect different size fractions for analysis. The function of the column cyclonic zone of was evaluated by comparing the quality of tailing and circulation middling. The flotation results showed that the concentrate with Ni grade of 1.78% and recovery of 65.56% was obtained under given test conditions. The content of main sulfide minerals and coarse particles in the circulation middling was higher than that in the tailing. The results indicated that, unlike conventional cyclone classification, separation achieved in the cyclonic zone of the column was not dependent on the particle size and density. Sulfide minerals with good floatability were easily captured by bubbles and moved toward the center of the column, even if these particles were coarser and heavier.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 2; 770-780
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Recovery mechanisms of sericite in microcrystalline graphite flotation
Autorzy:
Li, H.
Ou, L.
Feng, Q.
Chang, Z.
Powiązania:
https://bibliotekanauki.pl/articles/110055.pdf
Data publikacji:
2015
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
microcrystalline graphite
sericite
flotation
entrainment
entrapment
Opis:
Sericite is the main contaminant of concentrate in commercial microcrystalline graphite ore flotation. It was necessary to identify its recovery mechanisms so that the appropriate solution can be selected. In this study, the influence of sericite on flotation selectivity of microcrystalline graphite ore and its recovery mechanisms were investigated. Artificial mixtures flotation test suggested that sericite seriously reported into concentrate leading to poor flotation selectivity of microcrystalline graphite ore. However, the aggregation/dispersion behavior of artificial mixtures indicated that a large repulsive energy existed between sericite and microcrystalline graphite particles at pH 7.4, and sericite was not likely to report into graphite concentrate by slime coating. The results obtained from contact angle measurements and a technique of Warren showed that the floated sericite reached the froth via a combination of both entrainment and entrapment mechanisms, not via true flotation.
Źródło:
Physicochemical Problems of Mineral Processing; 2015, 51, 2; 387-400
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Calculation of laser radar cross-section of a spatial object and its experimental verification
Autorzy:
Cao, Y.-H.
Wang, Z.
Bai, L.
Wu, Z.
Li, H.-Y.
Li, Y.-H.
Powiązania:
https://bibliotekanauki.pl/articles/174167.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
bidirectional reflectance distribution function
BRDF
laser radar cross-section
LRCS
spatial object
Opis:
Bidirectional reflectance distribution function of some artificial satellite used materials at the wavelength of 1.06 μm was measured in laboratory. Bidirectional reflectance distribution function (BRDF) models of these materials were established with the five-parameter BRDF model. Laser radar cross-section of a scaled satellite with various materials was calculated, and characteristics of laser radar cross-section of the satellite were discussed. Measurement system to measure laser radar cross-section of the satellite was established and the scaled satellite model was measured. By analyzing the measured data and calculated data, it can be clearly seen that the BRDF of the surface materials and the laser incidence angle are two of main influential factors of the scaled satellite’s laser radar cross-section. These works can provide a reference for design of the lidar system.
Źródło:
Optica Applicata; 2017, 47, 4; 521-532
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies