Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "wirówka" wg kryterium: Temat


Wyświetlanie 1-2 z 2
Tytuł:
Własności filtracyjne zawiesiny po wirówkach DECANTER po dodaniu flokulantu Magnafloc 919
Filtering properties of suspension from the DECANTER centrifuge with Magnafloc 919 flocculant addition
Autorzy:
Palica, M.
Gierczycki, A.
Lemanowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/1819799.pdf
Data publikacji:
2009
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
zawiesina
filtracja
wirówka
flokulent
DECANTER
suspension
flocculant
Opis:
The results of an experimental research on dewatering of dump suspensionfrom the DECANTER centrifuge are presented in this paper. The suspension was taken from one of mines of the Jastrzębska Spółka Węglowa. This research allowed one to determine so called filtration parameters needed for the modeling of pressure filtration with cake compression. Some physical properties (density, mass fractions, moisture content, porosity, resistance of filter medium) as well as the kinetic constant coefficients (K and K') were concerned. The data was collected for the original suspension, i.e. liquid from the DECANTER centrifuge, and for the suspension with an addition of Magnafloc 919, flocculant used for flotoconcentrate, in the amount range between 10÷80 g/1 Mg of dry product, while the used dosage is 30 g/1 Mg. It was found that the addition of flocculant caused the increase of cake porosity and cake compressibility coefficient calculated according to the Tiller and Leu equation. Simultaneously, in small extends, the addition of flocculant resulted in increased cake's moisture content after the pressure filtration which is an unfavorable effect. On the other hand, it increased the constant kinetic coefficients K and K' in comparable conditions, enlarged mean arithmetic diameter of grains and accelerated the sedimentation process. The dosage of 30 g/1 Mg used by the maintenance personnel appears to be correct as well as the used filter cloth PT 912. One of the most interesting conclusion from this work is that the cake moisture content was lower after the pressure filtration than after the centrifuge filtration - this observation applies to the original dump suspension as well as to the one with the addition of flocculant. It is worth to emphasize that in case of the flocculant addition between 10÷30 g/1 Mg, Magnafloc 919 significantly influenced filtration properties of dump suspension. In case of the addition above 30 g/1 Mg that influence became very weak, therefore the application of the excessive addition is pointless from thetechnical point of view. The comparison of filtration parameters for dump suspension without and with the addition of flocculant suggests that there should not be any operating difficulties with the filtration process after a change of dewatering technology based on the usage of a settling tank for the dump suspension, recirculation of clear liquid and mixing of sludge with flotoconcentrate. One of advantages of this solution is the water - sludge circulation closure but it is connected with a greater DECANTER centrifuge load or with the addition of a supplementary centrifuge to the system.
Źródło:
Rocznik Ochrona Środowiska; 2009, Tom 11; 823-836
1506-218X
Pojawia się w:
Rocznik Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research on the influence of workpiece orientation during processing in disc centrifugal machine on the geometrical structure of its surface and processing efficiency
Autorzy:
Plichta, Jarosław
Juniewicz, Mateusz
Powiązania:
https://bibliotekanauki.pl/articles/2052231.pdf
Data publikacji:
2020
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
disc centrifugal machine
geometrical structure
wirówka tarczowa
struktura geometryczna
Opis:
The article describes the result of experiments which were intended to compare the results of different workpieces orientation in disc centrifugal machine. During experimental investigations, particular attention was paid to the optimal orientation the workpiece inworking charge. The results of the research presented in this article confirm the benefit of horizontal orientation of the workpiece to the motion of the media in the working charge
Źródło:
Journal of Mechanical and Energy Engineering; 2020, 4, 3; 221-226
2544-0780
2544-1671
Pojawia się w:
Journal of Mechanical and Energy Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies