Temat: piston internal combustion engine - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: External speed characteristics in engine with multi-stage fuel injection
Autorzy:: Ambrozik, A.
Ambrozik, T.
Kurczyński, D.
Łagowski, P.
Powiązania:: https://bibliotekanauki.pl/articles/245939.pdf
Data publikacji:: 2010
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: piston internal combustion engine
characteristics
engine work parameters
test bench investigations
engine fuels
Opis:: Increasingly higher demands pnt on piston internal combustion engines arę aimed at reducing their harmful impact on the natural environment. This refers primarily to nitrogen oxides, particulate matter and noise emissions. The reduction in emissions ofnoxious components oj exhaust gases in engines is achieved by means of, among others, the use of catalysts decreasing nitrogen oxide emissions, particulate matter filters and oxidising catalysts decreasing carbon monoxide and hydrocarbon emissions. Common Rail injection systems make it possible to increase the engine power, and to reduce fuel consumption, exhaust gas toxicity and noise produced by engines. With Common Rail systems, the pattern of fuel injection process can be designed, consequently the combustion process can be controlled. The paper presents the results of test bench investigations into a compression ignition 1.3 Multijet engine with multistage fuel injection, which is manufactured in Poland by Fiat-GM Powertrain Polska Company. The tests were conducted at a stand constructed at the Heat Engines Laboratory ofthe Kielce University of Technology. The scope of investigations included determining economic and energetic parameters of the engine work, and also environmental parameters, such as the concentration of nitrogen oxides NOX, carbon monoxide CO and carbon dioxide CO2 in exhaust gases, and exhaust gas smokiness. In tests, the engine operated under speed conditions and it was fuelled by two commercial diesel oils that had different physical and chemical properties.
Źródło:: Journal of KONES; 2010, 17, 1; 9-16
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Design of novel composite pistons for diesel engine
Autorzy:: Jankowski, A.
Powiązania:: https://bibliotekanauki.pl/articles/247362.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engine
diesel engine
piston engine
composite alloy
combustion engine performance
Opis:: The paper presents the requirements to be met by diesel engines and their components, in particular pistons for engines of military vehicles. These requirements are related to the mass of modern military vehicles, which has greatly increased. Materials for the piston should have a good strength properties and low hysteresis of thermal expansion coefficient α across the range of operating temperatures, good resistance to galling, low abrasion, low coefficient of friction and good functional properties. On the clearance of the piston in the cylinder, the coefficient of thermal expansion α and its hysteresis has a decisive influence. The paper includes information on the piston working clearances, the requirements for pistons materials, their chemical composition, standard materials for the forged pistons, for the cast pistons (silumin alloys) and for the composite pistons. The paper presents the changes in coefficient of thermal expansion for the alloy in the raw state and after heat treatment and pistons made of new composite material prior to motor testing and after these tests. The completed new pistons have a lower coefficient of thermal expansion and lower hysteresis α, which allows reducing the running piston and cylinder clearances with the resulting effects.
Źródło:: Journal of KONES; 2014, 21, 4; 211-216
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Research results of novel composite materials with low hysteresis during heating and cooling for pistons of combustion engines
Autorzy:: Sieminska, B.
Powiązania:: https://bibliotekanauki.pl/articles/245037.pdf
Data publikacji:: 2010
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engines
engine piston
thermal expansion
emissions
Opis:: Research results of novel silumins on pistons for combustion engines, which have high mechanical properties within the range of piston higher operating temperatures, 100-300°C, are presented in the paper. Silumins contain enlarging concentration of the nickel and copper alloy additives up to 4.0, and chrome and molybdenum alloy additives up to 1.0%. Occurrence of given microstructure in piston-silumins results in almost the same values of the coefficient thermal expansion during the heating up to the 300 °C temperature and during the next cooling into the ambient temperature. Small values of the coefficient of expansion of thermal and small differences between values of the coefficient of thermal expansion during heating and cooling enable on application of small values of working clearances between piston and the cylinder liner. As a consequence they make possible, the low exhaust emission level, and the low noise level. The pistons from alloys with small values ofthe coefficient of thermal expansion, small differences of this coefficient during heating and cooling are novel aspects presented in paper. Research results of strength and metallographic parameters, research results of the coefficient of thermal expansion, comparative engine research results are represented in the paper. In particular representative chemical components for a standard alloy and novel alloy, mechanical properties investigated alloys after solution heat treatment, wear resistance of novel alloy compared with two cast irons, ATD curves, fibrous construction, silicon construction, microstructure of novel alloy, courses of changes of the coefficient of thermal expansion in the function of the temperature during heating and cooling are presented in the paper.
Źródło:: Journal of KONES; 2010, 17, 1; 421-432
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: Verification of the precise position of the aircraft in air navigation based on the solution of the RTK-OTF technique
Autorzy:: Kowalski, M.
Jankowski, A.
Powiązania:: https://bibliotekanauki.pl/articles/242780.pdf
Data publikacji:: 2017
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engine
Diesel engine
engine piston
composite alloy
thermal stability
Opis:: Certain results of the comparative studies of the high-speed Diesel engine V-12 of the “W” series were presented in the article. The engine was modernised in regard of possibilities to achieve better performances at specific fuel consumption, smaller exhaust emission, smaller scavenge, lower noise and better thermal stability. The subject of this work is the piston cast of novel composite silumin. The development of novel composite silumin (aluminium-silicon alloy), which contains a little more Copper and Nickel, and the introduction of novel alloyed elements, such as Chromium, Molybdenum, Tungsten, increases the strength of the alloy and its thermal stability during successive heating and cooling. The pistons made of this alloy may have a little bigger outside diameter than the pistons made of PA-12 standard alloy, and a smaller clearance between the piston and cylinder liner. The pistons made of standard and novel alloy were mounted successively in the "W" engine. The full load and part load curves were determined. The lubrication oil consumption, fuel consumption, exhaust emission, blow-by and noise were determined too. The article presents the results of the above-mentioned research. The novel composite alloy enables further engine modernization because the engine should operate at higher pressure and temperature in the combustion chamber.
Źródło:: Journal of KONES; 2017, 24, 4; 99-108
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: Research performance of novel design of diesel engine
Autorzy:: Kowalski, M.
Jankowski, A.
Powiązania:: https://bibliotekanauki.pl/articles/949487.pdf
Data publikacji:: 2017
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engine
Diesel engine
engine piston
composite alloy
thermal stability
Opis:: Certain results of the comparative studies of the high-speed Diesel engine V-12 of the “W” series were presented in the article. The engine was modernised in regard of possibilities to achieve better performances at specific fuel consumption, smaller exhaust emission, smaller scavenge, lower noise and better thermal stability. The subject of this work is the piston cast of novel composite silumin. The development of novel composite silumin (aluminium-silicon alloy), which contains a little more Copper and Nickel, and the introduction of novel alloyed elements, such as Chromium, Molybdenum, Tungsten, increases the strength of the alloy and its thermal stability during successive heating and cooling. The pistons made of this alloy may have a little bigger outside diameter than the pistons made of PA-12 standard alloy, and a smaller clearance between the piston and cylinder liner. The pistons made of standard and novel alloy were mounted successively in the "W" engine. The full load and part load curves were determined. The lubrication oil consumption, fuel consumption, exhaust emission, blow-by and noise were determined too. The article presents the results of the above-mentioned research. The novel composite alloy enables further engine modernization because the engine should operate at higher pressure and temperature in the combustion chamber.
Źródło:: Journal of KONES; 2017, 24, 4; 99-108
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: Some effects of applying a new type of pistons for SU12-U diesel engine
Autorzy:: Jankowski, A.
Powiązania:: https://bibliotekanauki.pl/articles/246313.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engines
compression ignition engines
exhaust emissions
combustion engine piston
piston materials
testing of combustion engines
Opis:: In the task of research and development of internal combustion engines, the strong emphasis is placed on reducing emissions of harmful substances in exhaust gases, which include carbon monoxide (CO), unburned hydrocarbons (HC), nitrogen oxides (NOx), particulate matter (PM, PN); while maintaining a high engine performance and, above all, adequate: power, fuel consumption, noise. One of the possibilities to reduce emissions of HC and engine working noise is to reduce the clearance between the piston and the cylinder liner. This is possible only, when the permanent deformations of the piston are reduced, which result from rapid piston temperature changes (thermal shocks). The newly developed composite aluminum alloy is characterized by high strength parameters and low dimensional hysteresis during repeated heating and cooling. The S12-U engine pistons are made of this material, and they had a slightly larger nominal diameter than the standard pistons. They were then mounted in the engine. The engine was tested on a test stand with the modern, accurate measuring equipment. Test results show, that the HC and CO content in the exhaust gas has been reduced, exhaust gas blowby to the crankcase declined, smoke emission was reduced and engine lubricating oil consumption was also reduced. Analysis of test results indicates that this has been achieved, mainly by reducing the clearances between the piston and the cylinder. The article provides detailed test results, mainly in the form of charts, on which one can compare the results, achieved by the engine with new material pistons with results of the same engine, but with the standard pistons.
Źródło:: Journal of KONES; 2016, 23, 4; 167-174
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: Research and analysis of the results of the internal combustion engine locomotive during the 85-hour endurance test
Autorzy:: Borkowska, J.
Kaźmierczak, A.
Powiązania:: https://bibliotekanauki.pl/articles/245178.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: friction pair
internal combustion engine
piston
ring
cylinder
tribological properties
coating
EMD645
endurance test
diamond powder
Opis:: Piston – ring – cylinder assembly of combustion engine has many friction pairs examples, also one of them which decide about fastness to wear, it means first sealing ring – cylinder, called further very simply ring – cylinder unit. During work of this unit, we can observe wear of piston, precisely – of coating which is deposited on ring to prolong service life. Objective of this work was to realize a test of set durability of railway engine EMD645 with power about 1300 kW. Within the framework of this test were investigated a prototyped piston’s rings with diamond embankment. Piston rings are made of diamond coating technology with a porous chromium coating, where in pores is deposited on said diamond powder with a grain size about 1 micron. The work will be carried out of an analysis of collaboration piston – rings – cylinder unit in internal combustion engine and an analysis of the use of hard materials in friction pairs, including powders. Will be performed research of material and description of diamond powder, which will be applied to the piston rings. After stability, testing in the locomotive engine EMD645 on the basis of the collected results will be developed conclusions of the wearing intensity on piston ring and relating them to the requirements for coatings. The work aims to show the possibilities and benefits of the application of new protective coatings on structural elements of the internal combustion engine in order to reduce their wearing, which is consistent with the observed trend of technology development.
Źródło:: Journal of KONES; 2016, 23, 2; 53-59
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: Various designs of the two-stroke engine heads with the valve flushed system
Autorzy:: Łoza, Ł.
Kaźmierczak, A.
Borkowska, J.
Skorupa, P.
Krakowian, K.
Cienciała, M.
Powiązania:: https://bibliotekanauki.pl/articles/242546.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: engine
two-stroke
internal combustion
valve flushed system
piston-controlled cam
high petrol consumption
oil in the petrol
toxic by-products
loud noise
uneven running
low efficiency
Opis:: The two-stroke engines have never acquired the popularity of the four-stroke engines due to their inherent performance limitations. The tasks of many engineering teams were to find the basic causes, which resulted in the inferior performance of these engines. Today’s task is to build a two-stroke engine whose performance could match that of a four-stroke engine in areas of common use. The most typical performance problems of a two-stroke engine are high petrol consumption caused by low efficiency, toxic by-products of combustion being emitted into the atmosphere (caused by oil present in the petrol), and uneven and loud engine noise. The greatest challenge is to achieve a good chamber purge during one stroke in which the fresh fuel mixture flows through the piston-controlled inlet port while at the same time the fumes are being exhausted through the outlet port. This in contrast with the four-stroke engines where the intake and exhaust are each done with two separate strokes. From the energy point of view, the two-stroke engine is not efficient because a certain amount of fresh fuel is being wasted in the exhaust fumes. We propose to replace the piston-controlled cam with the valve-flushed system, which will cause the combustion process to become more efficient. The purpose of this paper is to present various designs of the engine heads and analyse their performance. The goal of this proposal is to choose the best combination of these engine heads in order to achieve the optimum overall engine performance.
Źródło:: Journal of KONES; 2015, 22, 4; 187-190
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "piston internal combustion engine" wg kryterium: Temat

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język