Temat: EiS - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: The analysis of finishing tooling influence on corrosion properties researched by EIS
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/248058.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: burnishing
surface layers
angular momentum pump
corrosion properties
EIS
Opis:: Angular momentum pumps are very often applied onboard ships. These pumps are used in cooling circuits of medium and high power engines, power plant boilers and in bilge, ballast and fire installations. Very extensive use of angular momentum pumps on board is connected with their numerous advantages. During operation the wear of marine hull, the rotor and shaft seals take place. The research attempts to increase the service life of shafts. The article presents the research results referring to the analysis of the influence of finish treatment (lathing, grinding and burnishing) on the corrosion properties of steel applied to marine pump shafts. The research was performed on a roller of 40 mm in diameter made of X5CrNi18-10 (AISI 304 L) stainless steel. The lathing process was carried out by means of a WNMG WF 080408 Sandvik Coromant cutting tool with replaceable inserts. The grinding process was performed by grinding attachment for lathes. The 1 - 80x10x32 - 99C 80-N V grinding wheel was used for the process. The process of burnishing was done by SRMD burnisher by Yamato. In addition, the influence of the burnisher passes number on the corrosion properties was determined. The paper will present the results of electrochemical impedance spectroscopy research. To conduct the survey the Atlas 0531 EU and IA potentiostat was used. Determination of the corrosion process parameters was performed computer programs: AtlasLab 2.0 and EIS Spectrum Analyzer.
Źródło:: Journal of KONES; 2012, 19, 1; 237-244
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: EIS research of AW - 7020 alloy joints welded by MIG
Autorzy:: Dudzik, K.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/248097.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: electrochemical impedance spectroscopy (EIS)
aluminium alloys
MIG welding
corrosion
Opis:: The results of corrosion properties research of aluminum alloy AW 7020 (AlZn5Mg1) welded by MIG were presented. In the article the parameters for MIG welding of sheets made of AlZn5Mg1 (7020) alloy was presented. Metallographic analysis of bonds showed a proper structural construction MIG welded 7020 aluminum alloy. EIS measurement was performed in three electrode system in artificial seawater (3.5% NaCl). Impedance studies were carried out at the corrosion potential. Changed voltage signal amplitude in the range plus or minus 10 mV and frequency range of changes was as follows: 100 kHz - 0.1 Hz. Atlas 0531 EU and IA potentiostat was used for studies. Model in the form of an electrical equivalent circuit replacement was chosen for the test object. The results of electrochemical impedance spectroscopy are presented graphically in the Nyquist charts matched with the theoretical curve to them and in the form of parameters characterizing the corrosion process. Obtained results were statistically analyzed. Much better resistance to electrochemical corrosion was found for the native material then joint welded by MIG of 7020 aluminum alloy. The most important parameter - charge transfer resistance value of a double layer Rct for sample of native material is higher than for the sample welded by MIG. Original value is received results of the corrosion properties of MIG welded AlZn5Mg1 alloy compared with the native material.
Źródło:: Journal of KONES; 2012, 19, 1; 83-88
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Corrosive properties distribution in AW-7020 alloy joints welded by FSW
Autorzy:: Dudzik, K.
Powiązania:: https://bibliotekanauki.pl/articles/247352.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: electrochemical impedance spectroscopy
EIS
friction stir welding
FSW
welding
corrosion
Opis:: The results of corrosion properties research of aluminum alloy AW 7020 (AlZn5Mg1) welded by Friction Stir Welding were presented. In the article the parameters for friction stir welding of sheets made of AlZn5Mg1 (7020) alloy were presented. Corrosion tests were performed on the surface of the FSW joined sheets depending on the distance from the centre of the weld. EIS measurement was performed in three-electrode system in an artificial seawater (3.5% NaCl). Impedance studies were carried out at the corrosion potential. Changed voltage signal amplitude in the range ± 10 mV and frequency range of changes was as follows: 100 kHz - 0.1 Hz. Atlas 0531 EU & IA potentiostat was used for studies. Model in the form of an electrical equivalent circuit replacement was chosen for the test object. The results of electrochemical impedance spectroscopy are presented graphically in the Nyquist charts matched with the theoretical curve to them and in the form of parameters characterizing the corrosion process. Obtained results were statistically analysed. Better resistance to electrochemical corrosion was found for the native material then joint welded by FSW of 7020 aluminum alloy. Worse corrosion properties were observed in the advancing side of the weld than in the retreating side of the weld. Original value are received results of the corrosion properties distribution of FSW welded AW-7020 aluminium alloy.
Źródło:: Journal of KONES; 2014, 21, 4; 79-85
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: Effect of finishing on the corrosion properties of flame sprayed Ni-5%Al and Ni-5%Al-Al2O3 coatings
Autorzy:: Charchalis, A.
Starosta, R.
Powiązania:: https://bibliotekanauki.pl/articles/247338.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: flame spraying
composite coating
Ni-Al
burnishing
corrosion
potentiodynamic test
EIS test
Opis:: The Ni-5%Al alloy and Ni-5% Al-Al2O3 composite coatings were obtained by a flame spraying method, “Casto- Dyn DS 8000” torch was used. The coatings onto a substrate made of austenitic stainless steel (X5CrNi18-10) were sprayed. The coatings were subjected to turning, burnishing and grinding. The evaluation of corrosion properties were based on the measurements of direct current (potentiodynamic method) and the alternating current (EIS method). Corrosion tests were performed in a 3.5% sodium chloride solution. On the basis of studies, the effect of finishing type on the corrosion properties of flame sprayed coatings has been demonstrated. The lowest corrosion current density was found for Ni-5%Al coatings after burnishing, icorr value equal to 0.76 μA/cm2, and the charge transfer resistance was 31063 Ω/cm2. The lowest resistance to corrosion of grinded Ni-5%Al-Al2O3 composite coatings was observed. These coatings were characterized by the following parameters of corrosion process: icorr = 14.01 μA/cm2, Rct = 3260 Ω/cm2. Burnishing caused increased corrosion resistance of both coatings. Due to reduced roughness and waviness are obtained reduction of the area of the actual burnished coatings compared to turned coatings. Thus, it is resulting in reduced values of corrosion current density. After finishing treatment, the thermally sprayed Ni-5%Al-15%Al2O3 coatings characterized by lower corrosion resistance compared to the alloy coating. The presence of the reinforcing phase in the coating promotes the increase of the porosity. Burnishing does not cause a significant change in porosity of the coating. The flame sprayed coatings on nickel-based have a tendency to localized corrosion in seawater environment.
Źródło:: Journal of KONES; 2014, 21, 4; 29-36
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: Effect of burnishing on the corrosion properties of Ni-5%Al AND Ni-5%Al-15%Al2O3 coatings obtained by plasma spraying
Autorzy:: Starosta, R.
Powiązania:: https://bibliotekanauki.pl/articles/245849.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: plasma spraying
composite coating
Ni-Al
burnishing
corrosion
polarization test
EIS test
Opis:: The Ni-5%Al alloy coatings and Ni-5% Al-15%Al2O3 composite coatings were obtained by plasma spraying method. The PN120 gun was used. The coatings onto a shaft made of austenitic stainless steel (X5CrNi 18-10) were sprayed. The coatings were subjected to turning, burnishing. The evaluation of corrosion properties were based on the measurements of corrosion current density and corrosion potential (polarization method), the charge transfer resistance and exponent of constant phase element impedance (electrochemical impedance spectroscopy method). Corrosion tests were performed in replacement seawater (3.5% sodium chloride solution). On the basis of studies, the effect of finishing type on the corrosion properties of plasma sprayed coatings has been demonstrated. The lowest corrosion current density was found for Ni-5% Al coatings after burnishing, icorr value equal to 0.96 A/cm2, and the charge transfer resistance was 27007 Ωcm2. The lowest resistance to corrosion of turned Ni-5%Al-15%Al2O3 composite coatings was observed. These coatings were characterized by the following parameters of corrosion process: icorr = 17.64 A/cm2, Rct = 2137 Ωcm2. Burnishing caused increased corrosion resistance of coatings. Due to reduced roughness and waviness are obtained reduction of the area of the actual burnished coatings compared to turned coatings. Thus, it is resulting in reduced values of corrosion current density. After finishing treatment, the plasma sprayed Ni-5%Al-15%Al2O3 coatings characterized by lower corrosion resistance compared to the alloy coating. The presence of the reinforcing phase in the coating promotes the increase of the porosity. The plasma sprayed coatings on nickel matrix had a tendency to localized corrosion in sodium chloride solution.
Źródło:: Journal of KONES; 2014, 21, 1; 273-280
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "EiS" wg kryterium: Temat

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język