Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Rokicki, J" wg kryterium: Autor


Wyświetlanie 1-2 z 2
Tytuł:
Thermal analyses of exhaust system on combustion engine
Autorzy:
Dybała, J.
Lubikowski, K.
Rokicki, K.
Szulim, P.
Wikary, M.
Powiązania:
https://bibliotekanauki.pl/articles/241765.pdf
Data publikacji:
2012
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
cogeneration of energy
exhaust system
thermoelectric generator
Opis:
Nowadays there are more and more discussions on acquisition of energy from sources other than natural sources of energy. Many scientific research centres deal with the issue of energy recovery as well as use of energy from renewable sources. The communities associated with the automotive industry devote a lot of attention to the issue of improving the energy efficiency of vehicles. Since a combustion engine uses less than half of the energy produced during the combustion process, thus the issues of recovery of thermal energy and its conversion into electrical energy evoke increasing interest. The article presents the process of examination of the temperature of the exhaust system in a car engine operating in a laboratory environment. Measuring equipment was used to the temperatures' determine. Analysis of distribution of temperatures in the exhaust system creates grounds for rational selection of the places where the thermal energy recuperation systems should be installed. At present, the possibilities of recovery of thermal energy are still seriously restricted by the properties of the materials of which the elements of the thermal energy recovery systems are made. High propensity of these elements to thermal defects is a serious problem in practical application of these materials in thermal energy recovery systems. The results obtained in an experiment serve as the basis for determining the locations where thermoelectric generators should be installed while accounting for their thermal limitations.
Źródło:
Journal of KONES; 2012, 19, 4; 173-178
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Determination of heat treatment parameters for heavily - loaded aircraft engine components
Autorzy:
Rokicki, P.
Dychtoń, K.
Nowotnik, A.
Drajewicz, M.
Sieniawski, J.
Kurkowski, D.
Wierzbińska, M
Jakubowicz, G.
Budzik, G.
Powiązania:
https://bibliotekanauki.pl/articles/243068.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
aircraft engine components
vacuum carburizing
heat treatment
quenching
alloy steel microstructure
Opis:
Gears, due to their complex shape, carried load and required accuracy are ones of most complex aircraft engine parts. Single tooth damage usually breaks the power transmission and causes failure of the entire gear system. Adequate sustainability and guarantees of transmission is therefore a condition for secure operation of whole device. Particularly high requirements for reliability are put to transmissions used in the aerospace industry. Due to the loads which are transmitted through the gears, the materials used by the manufacturer must have not only high strength but also show the abrasion resistance of the surface layer and the ductility of the core. Proper parameters matching allows to create an element that can operate at higher stresses and loads. In addition, factor strength and abrasion resistance of the surface layer has a significant impact on the life of the gear. Thermo-chemical treatment of industrial gears is a fundamental process, which gives them adequate mechanical properties regarding loads they carry and the surface conditions of work. Among many methods of thermo-chemical treatment used in the industry, the most distinctive are innovative technologies designed to reduce process costs and being more environmentally friendly. The most promising methods in the discussed field are vacuum carburizing and high-pressure hardening, which by their specification of work significantly reduce the emission of CO2 and the duration of the process, without reducing the quality of the final product. The main aim of the paper is to present criteria for selection of heat treatment parameters as a part of thermo-chemical treatment process performed using vacuum methods. Proper heat treatment parameters are crucial in programming of some of final material characteristics as grain size and retained austenite morphology.
Źródło:
Journal of KONES; 2013, 20, 2; 349-354
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies