Autor: Bieniek, A - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: Conception of cylinder pressure based diesel injection control system
Autorzy:: Bieniek, A.
Powiązania:: https://bibliotekanauki.pl/articles/245444.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: diesel injection
cylinder pressure
control system
emission
heat release
Opis:: Control of diesel fuel injection is very important and has influence not only at engine operating conditions but also at emission of toxic gases as NOx, HC, and Particulate Matter (PM) are effect of combustion process. Directly observing of combustion process is very difficult, but implementation to injection control algorithm procedures based on additional sensors as knock sensor, cylinder pressure sensor and observing of rotational speed course could give enough information to optimize control algorithm. In traditional diffusion-burn diesel combustion start of combustion occurs a cetane-number based time delay after the start of the fuel injection. To fulfill of new emission standards is need to observing not only start of combustion but also whole combustion process. In the paper conception of injection control system applied with combustion process observer based on additional sensors. Closed-loop feedback control of cylinder pressure sensor and advanced control algorithm with high-resolution rotational speed sensor offers the potential to improve controllability of combustion process. Advanced control system based on heat release estimated from cylinder pressure and rotational speed fluctuations enabling improving engine exhaust emissions, engine performance and reduced noise emission. Introducing into control system a low cost glow plug integrated cylinder pressure sensor allow to achieve complete injection control system with advanced functions which could be very effective also in aspect of fuel consumption reduction.
Źródło:: Journal of KONES; 2011, 18, 3; 27-35
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Irregularity of rotational speed of diesel engine with modified fuel injection system
Autorzy:: Kowalski, D.
Bieniek, A.
Brol, S.
Powiązania:: https://bibliotekanauki.pl/articles/247225.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: injection pump
pollutant emission
electric valves
transport
off-road
Opis:: The operation of diesel engine is closely connected with controlling the process of injecting the fuel into the cylinder. It influences proper combustion process, which translates directly into irregular engine operation resulting in dumping and noise. It is related to improper control of fuel injection which is connected with improper completion of expected control strategy that can be a result of defective injection system. Irregular engine operation can also be caused by total lack of initiated combustion process in specific cylinder of the engine or in several cylinders, described as misfire, or ca be a result of differences in combustion process in individual operation cycles / engine cylinders. The effect is an engine working irregularly (there is instability of rotational speed) and emitting increased amount of pollutants. As a consequence the secondary fuel purification systems located in the exhaust system can be damaged. Therefore, it is required to choose the fuel injection control parameters in a way that enables detecting and correcting the process of fuel injection in order to minimize effects resulting from improper process of fuel combustion in individual cylinders or even lack thereof. It is useful to suggest diagnostic parameter that can be used to detect engine faultiness or elements of the accessories such as e.g. injection system. Ability to apply such control and correction of injection dose is provided by modified mechatronic in-line injection pump. The study shows results of researches on modified injection system with mechatronic in-line injection pump that enables identification of misfire and preventing irregular operation of diesel engine.
Źródło:: Journal of KONES; 2011, 18, 4; 199-204
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Adaptive control of exhaust gas recirculation at nonroad vehicle diesel engine
Autorzy:: Bieniek, A.
Graba, M.
Lechowicz, A.
Powiązania:: https://bibliotekanauki.pl/articles/247302.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: exhaust gas recirculation (EGR)
NOx emissions reduction
adaptive control
EGR valve
Opis:: At diesel engines with fuel direct injection, the problems with toxic exhaust compounds concern mainly nitrogen oxides (NOx) and Particulate Matter (PM). For reduction of the NOx's, the exhaust gases are feedback to the combustion chamber. This results with a lower combustion temperature and decrease the emission of NOx gasses. The mass of the recirculated gases cannot be too high because it might lead to an increase in the PM emission. In nonroad vehicle engine the component responsible for the exhaust gases recirculation is most a two state (open/close) EGR Valve. Another problem in this type of combustion engines is volatility of its ecological parameters during exploitation. The reasons are various operation conditions of the engine, fuel quality ect. So, according to the proposed solutions, the engine controller must track these variations. The mass of recirculated gasses must also be corrected. In the proposed solution the EGR valve is a prototype construction of an electronically controlled EGR. The openness of the valve is freely programmable and is controlled by adaptive algorithm saved in the ECU (Electronic Control Unit). As feedback signal to control the openness of EGR valve is used an NOx sensor placed at engine outlet pipe. The paper describe an control circuit of EGR Valve and include research results of nonroad vehicle diesel emissions (NOx and PM missions). The proposed adaptive control of EGR Valve shows potential to reduce especially NOx emissions in aspect to fulfill further emission regulation TIER/Euro
Źródło:: Journal of KONES; 2011, 18, 4; 11-18
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: The System for estimation parameters of internal combustion engine in the road test
Autorzy:: Mamala, J.
Brol, S.
Bieniek, A.
Powiązania:: https://bibliotekanauki.pl/articles/242285.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engines
road test
system of data transmission CAN BUS
Opis:: Current internal combustion engine technology for road vehicles allows us to meet the existing and planned future standards for emission. However, the motion of a moving vehicle used in real operating conditions is frequent changes of the values of power in the powertrain. The analysis of the results of the road test through a measurement of parameters of engine in a passenger car proves, that the changes of parameters engine are frequent. The paper presents method measurement parameters form system of data transmission CAN BUS and estimation is performed using measurement accelerometer car's chassis of parameters internal combustion engine determined on road test. Estimation of main parameters of internal combustion engine is made with use of measured quantities such as: car mass and acceleration collected in function of vehicle linear velocity. The most essential problems in this approach, considered as primary method errors, are minimization of underestimation of moment of inertia of rotating elements in drivetrain and efficiency of drivetrain itself. Moreover it is vital to determine as precise as possible vehicle acceleration and its linear velocity in presence of disturbances - mainly chassis movements and additional accelerations, which comes from pavement unevenness (roughness). In this article application of several sensors of different quantities for increase of accuracy of PAAF 2 (Power Acceleration And Force) device in relation to prototype device predecessor is taken into consideration.
Źródło:: Journal of KONES; 2011, 18, 2; 279-286
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: Comparative analysis of the fuel consumption of vehicles equipped with various types of automatic transmissions
Autorzy:: Graba, M.
Mamala, J.
Bieniek, A.
Ulfik, A.
Powiązania:: https://bibliotekanauki.pl/articles/949511.pdf
Data publikacji:: 2018
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: automatic transmission
fuel consumption
control algorithm
CVT
automotive powertrain
road slope
Opis:: The growing number of vehicles moving on Polish roads equipped with various types of automatic transmissions prompted the authors of this publication to carry out research to assess the impact of the use of this type of transmission on the fuel consumption of these vehicles. The presented article presents a comparative analysis of the fuel consumption of vehicles of different manufacturers equipped with automatic transmissions moving in specially prepared driving cycles for research purposes. In the developed driving cycle, the vehicle speed was gradually increased every 10 km/h, maintaining each speed for a period of at least 30 seconds in order to stabilize the measurement results. The tests were carried out for various load stages of the drive system. Load differentiation was made by simulating driving in the prepared cycle for simulated different slopes of the road. The tests were carried out on the MAHA MSR500 chassis dynamometer, and the obtained results for the vehicle moving in automatic mode, where the transmission controller selected the gear ratio according to the programmed algorithm, were compared with the vehicle's fuel consumption for the vehicle gear selected by the driver in the driving cycle. The control software used to test the chassis dynamometer allows taking into account the increasing resistance of traffic along with the increase of vehicle speed, which greatly approximates the simulated conditions in the laboratory to the conditions on the road. The main purpose of this publication is to check whether using automatic transmissions or other control algorithm of these gears can achieve a reduction in fuel consumption.
Źródło:: Journal of KONES; 2018, 25, 4; 119-124
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: Comparative analysis of the operating indexes of manually and automatically controlled passenger car powertrain system at variable load states
Autorzy:: Graba, M.
Mamala, J.
Bieniek, A.
Hennek, K.
Powiązania:: https://bibliotekanauki.pl/articles/245358.pdf
Data publikacji:: 2017
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: fuel consumption
spark ignition engine
variable load
engine efficiency
motion resistance
Opis:: This article reports the results of a study into operating parameters of a system consisting of an SI engine and a powertrain in a Fiat Panda passenger car in the conditions of a variable load. The analysis was primarily concerned with the variability of fuel consumption resulting of the changing load applied to the driving wheels in the conditions of a test performed on chassis dynamometer for manual and automatic controlled transmission gear change The test bench included a dedicated driving cycle, which was developed as cycle with periodically changed constant linear speed of the car every 10 km/h. According to the vehicle set speed, the load on its wheels was determined by the basic resistance as rolling resistance, air resistance and resistance corresponding to road inclination. Each period of a drive cycle corresponding to steady state driving gave the average instantaneous values of drive system performance indicators. The waveforms of these indicators were recorded and then averaged and presented as representative points of the powertrain system that were analysed. The focus of the study involved the identification of the points characterized with the minimum specific fuel consumption and impact of type of powertrain control on emission of CO2 from passenger car SI engines.
Źródło:: Journal of KONES; 2017, 24, 4; 39-46
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: Nitrogen oxides emission estimator for a diesel engine use to reduce the emission of harmful substances in exhaust gas to environment
Autorzy:: Graba, M.
Mamala, J
Bieniek, A.
Hennek, K.
Powiązania:: https://bibliotekanauki.pl/articles/246302.pdf
Data publikacji:: 2017
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: nitrogen oxides emission
diesel engine
estimation
combustion engines
air pollution
environmental protection
Opis:: This article reports the results of experimental and numerical analysis of emissions of nitrogen oxides in exhaust gas to the environment from a turbocharged diesel engine of a tractor. The problem of identifying nitrogen oxides emissions from the exhaust gases was formulated and subsequently solved, based on data gained from measurements. The results of estimation of nitrogen oxides emissions were verified on the basis of research on a test object. The object of the study and a non-linear static model of nitrogen oxides emission were also described for two systems – with and without exhaust gas recirculation. The article demonstrates that the use of an adequately selected mathematical model can lead to the estimation of emissions of nitrogen oxides contained in the exhaust gas of diesel engines in an off-road vehicle. The created model can be used to control the valve of the exhaust gas of recirculation system and so reduce the emission of harmful substances to the environment. The presented research results show the comparison of estimated and measured nitrogen oxides concentration. The estimated value from the mathematical model concentration is about from 0.7 s to 1 s earlier than the value measured by the sensor, therefore the exhaust gas recirculation system could be controlled accordingly before nitrogen oxides are formed.
Źródło:: Journal of KONES; 2017, 24, 3; 87-94
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: Device for control the valvetrain and cylinder pressure of a spark-ignition engine
Autorzy:: Mamala, J.
Graba, M.
Bieniek, A.
Hennek, K.
Powiązania:: https://bibliotekanauki.pl/articles/241981.pdf
Data publikacji:: 2018
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engines
environmental protection
variable compression ratio
valve control
Opis:: This article describes the method of controlling an electric magnetic linear actuator that moves an inlet valve of an internal combustion engine. Thanks to the use of the electric control of the inlet valve of the internal combustion engine, it was possible to implement a variable effective compression ratio of the operating power unit, adapting it to the current needs and engine load. In this design, valvetrain was modified by introducing an autonomous intake valve operation with the use of a specially designed electromagnetic actuator. The introduction of this system necessitated an additional modification of the intake camshaft. The control was carried out with the use of a real-time controller with a built-in FPGA unit. The proposed design of a system with an electromagnetic actuator will allow obtaining an additional degree of freedom in the control unit. Particular attention should be paid to registered values or air pressure in the intake stroke for a closed or partially opened throttle, which generates significant pumping losses. The use of an electromagnetic actuator in the intake can help reduce said losses.
Źródło:: Journal of KONES; 2018, 25, 3; 339-346
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 9.

Tytuł:: "Off Road" vehicles in the aspect of future emission exhaust quality standards
Autorzy:: Jantos, J.
Mamala, J.
Bieniek, A.
Kowalski, D.
Graba, M.
Powiązania:: https://bibliotekanauki.pl/articles/245720.pdf
Data publikacji:: 2009
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: injection pump
pollutant emission
electric valves
transport
off-road
Opis:: Current engine technology for on-road vehicles allows us to meet the existing and planned future standards for emission. Because combustion engines, especially self-igniting are being used for very different purposes like: road transport, rail-way transport, shipping, industry, military and agriculture, these engines work in different and often difficult conditions. A very significant group of vehicles used for the most difficult of the a forementioned areas ofuse are "Off-Road" vehicles. For those vehicles we also use rigorous regulations to govern dangerous chemical emissions such as Tier, Bin and Californian LEV. In those types of vehicles the fuel powered systems very often use mechanically controlled diesel injection pump. These pumps are characterized by high tolerance to the quality and type ofpetrol as well as reliability, which is very important especially in "off-road" vehicles. At work a conception was described of system of powering the engine diesel which will let for reaching of future emission exhaust quality standards. In the paper only initial outline of the idea of the injection 's system for „off-road" vehicles, is introduced. This system needs follow-on in the field both interactions with the EGR valve, with the injection 's system as well as in the matter of interaction with ECU of the injection 's system.
Źródło:: Journal of KONES; 2009, 16, 4; 201-206
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 10.

Tytuł:: The system of supercharging for the spark-ignition engine
Układ doładowania silnika o zapłonie iskrowym
Autorzy:: Mamala, J.
Jantos, J.
Brol, S.
Malewicz, K.
Bieniek, A.
Powiązania:: https://bibliotekanauki.pl/articles/243245.pdf
Data publikacji:: 2007
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: doładowanie zasobnikowe
zdolność przyspieszania
silnik spalinowy
combustion engine
powertrain systems
mechanical inertia
charging system
Opis:: The most disadvantageous system of the automobile, because of its damaging influence on environment is powertrain. This notion means engine connection with powertrain, which is very important in respect of ecology and safety. In the matter of safety very important is ability to accelerating with rapid depressed accelerator pedal. This situation takes place during overtaking process, which is caused by driving force deficiency from engine and powertrain mechanical inertia. It has negative influence on overtaking process and also on driving comfort. This phenomenon described in works, mainly come from accumulation of mechanical energy of powertrain. Numerous research centres in the world have undertaken examinations with an aim of solving this problem. However, a successful solution to this problem has to meet a number of prerequisites of technological and economic nature. The technological ones have to involve the uncomplicated construction while the economic ones are associated with the need for low cost of application of the solution put forward. The latter question is related to meeting numerous conditions and results from the effects of special testing as a result of specific operating conditions of power transmission system. In numerous research centres abroad additional energy sources including plungers or electrical motors are installed in order for the compensation of mechanical inertia. Another way of compensation for the mechanical inertia of the transmission system is gaining larger momentum from the driving unit at the time of its abrupt acceleration. A successful solution to this problem may lie in the application of an additional boost with surplus charging in the fuel supply system. They analyzed in the paper structure of the system of charging the internal-combustion engine up about the spark ignition in the purpose for the compensation for the shortage of the driving force on wheels of the car and results of preliminary research were presented.
Źródło:: Journal of KONES; 2007, 14, 2; 291-298
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 11.

Tytuł:: Influence of CVT operating parameters at SI engine operating indexes
Wpływ parametrów pracy przekładni CVT na wskaźniki pracy silnika ZI
Autorzy:: Bieniek, A.
Jantos, J.
Hetmańczyk, I.
Mamala, J.
Borecki, D.
Powiązania:: https://bibliotekanauki.pl/articles/243130.pdf
Data publikacji:: 2007
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: układ napędowy
bezstopniowa przekładnia mechaniczna
silnik ZI
emisja
zużycie paliwa
transmission system
CVT
SI engine
pollution emission
fuel consumption
Opis:: Wykorzystanie silnika spalinowego w charakterze jednostki napędowej (JN) wiąże się z koniecznością zastosowania rozbudowanego układu przeniesienia napędu (UPN). Tylko dzięki odpowiedniemu skojarzeniu silnika spalinowego z UPN jest możliwe uzyskanie pożądanych cech całego układu napędowego (UN). Aktualnie przy obecnym poziomie technologii i porównywalnej niezawodności oraz trwałości różnych rozwiązań, kryteriami podstawowymi są zużycie paliwa, emisja substancji szkodliwych oraz właściwości dynamiczne samochodu. Te trzy podstawowe kryteria są częściowo sprzeczne. Zadowalający wynik można uzyskać wyłącznie przy dużej liczbie, możliwych do zrealizowania w UPN, wartości przełożenia. Ze wzrostem tej liczby pojawia się jednak problem racjonalnego wyboru, którego przeciętny kierujący nie jest w stanie poprawnie rozwiązać. W rezultacie zwiększa się znacznie liczba automatów napędowych, w których wybór przełożenia UPN jest zalgorytmizowany. Wśród możliwych rozwiązań rośnie udział bezstopniowych przekładni mechanicznych (Continuously Variable Transmission - CVT) dysponujących znacznym zakresem zmiany przełożenia, a jednocześnie umożliwiających płynną zmianę jego wartości. W pracy dokonano analizy wpływu parametrów pracy bezstopniowej przekładni cięgnowej na wskaźniki pracy silnika o zapłonie iskrowym. Przeprowadzona własna modyfikacja układu hydraulicznego przekładni pozwala na obserwację i zmianę istotnych parametrów jej pracy. W referacie przedstawiono wyniki badań stanowiskowych oraz drogowych przeprowadzonych w cyklach jezdnych i próbach rozpędzania. Poza podstawowymi parametrami pracy układu napędowego rejestrowano zużycie paliwa oraz emisję substancji szkodliwych uwzględniając zróżnicowane algorytmy sterowania przekładnią.
The advantage of combustion engine as power source at driving unit is connected with necessity of application of developed automotive transmission system. Only in the case of appropriate associate of combustion engine and transmission is it possible to achieving of eligible characteristic of transmission system. At currently technology level and comparable reliability and durability of different solutions the basic criterions are fuel consumptions, pollutant emissions and vehicle dynamical property. These basic criteria are at variance each other. Satisfactory result could be achieved exclusively on high number of transmission ratios. Increase of transmission ratio numbers is connected with problem of its reasonable selection, which is difficult to solve through the average driver. The result is rapidly growth of automated transmission system, were the transmission ratio is selected according to transmission control algorithm. In this transmission group grow the participation of Continuously Variable Transmissions- CVT, which disposes with high transmission ratio range and simultaneously enables to change its value fluently. In this paper the influence of CVT operating parameters at SI engine operating indexes are analysed. The own modification of transmission control unit enables to observing and control of significant transmission operating parameters. In this work the results of test bench and road tests at acceleration test and driving cycle are presented. Besides of registration of basic operating parameters the results of fuel consumption and pollutant emission are also observed.
Źródło:: Journal of KONES; 2007, 14, 3; 49-60
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "Bieniek, A" wg kryterium: Autor

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język