Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "test model" wg kryterium: Temat


Wyświetlanie 1-10 z 10
Tytuł:
Test studies of the resistance and seakeeping performance of a trimaran planing hull
Autorzy:
Ma, W.
Sun, H.
Zou, J.
Zhuang, J.
Powiązania:
https://bibliotekanauki.pl/articles/259495.pdf
Data publikacji:
2015
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
trimaran planing hull
appendix
resistance
seakeeping
model test
Opis:
Towing tank tests in calm water were performed on a trimaran planing hull to verify its navigational properties with different displacements and centres of gravity, as well as to assess the effects of air jets and bilge keels on the hull’s planing capabilities, and to increase the longitudinal stability of the hull. Hydrostatic roll tests, zero speed tests, and sea trials in the presence of regular waves were conducted to investigate the hull’s seakeeping ability. The test results indicate that the influence of the location of the centre of gravity on the hull resistance is similar to that of a normal trimaran planing hull; namely, moving the centre of gravity backward will reduce the resistance but lower the stability. Bilge keels improve the longitudinal stability but slightly affect the resistance, and the presence of air jets in the hull’s channels decreases the trim angle and increases heaving but has little effect on the resistance. Frequent small-angle rolling occurs in waves. The heaving and pitching motions peak at the encounter frequency of , and the peaks increase with velocity and move towards greater encounter frequencies. When the encounter frequency exceeds, the hull motion decreases, which leads to changes in the navigation speed and frequency.
Źródło:
Polish Maritime Research; 2015, 1; 22-27
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Model tests on characteristic of suction caissons in saturated fine sand under intermittent loading
Autorzy:
Shi, P.
Powiązania:
https://bibliotekanauki.pl/articles/258534.pdf
Data publikacji:
2018
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
intermittent suction installation
model test
sand
suction caisson
Opis:
Suction caissons are often used for the caissons of both offshore oil platforms and offshore wind power projects because of their advantages of simple construction, economical cost, and reusability. In this study, model tests were conducted in sand in order to investigate the effects of the caisson installation method on the penetration depth and the critical suction. Results of the test program showed that the method of changing the frequency of suction during different stages of the process can increase the penetration depth of the caisson. Combining with the deformation of the soil body inside and outside the caisson, the existing method for calculating the critical suction is modified, and the critical suction calculation equation of the discontinuous penetration test is proposed. Based on the test results, the calculation equation of the soil heave height can be more accurate predicted. The analysis results verify that the calculation method and the actual results are in good agreement.
Źródło:
Polish Maritime Research; 2018, S 3; 127-135
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical and experimental study on seakeeping performance of a high-speed trimaran with T-foil in head waves
Autorzy:
Li, Ang
Li, Yunbo
Powiązania:
https://bibliotekanauki.pl/articles/258842.pdf
Data publikacji:
2019
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
trimaran
T-foil
URANS
longitudinal motion
model test
Opis:
The longitudinal motion characteristics of a slender trimaran equipped with and without a T-foil near the bow are investigated by experimental and numerical methods. Computational fluid dynamics ( CFD) method is used in this study. The seakeeping characteristics such as heave, pitch and vertical acceleration in head regular waves are analyzed in various wave conditions. Numerical simulations have been validated by comparisons with experimental tests. The influence of large wave amplitudes and size of T-foil on the longitudinal motion of trimaran are analyzed. The present systematic study demonstrates that the numerical results are in a reasonable agreement with the experimental data. The research implied that the longitudinal motion response values are greatly reduced with the use of T-foil.
Źródło:
Polish Maritime Research; 2019, 3; 65-77
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Motion prediction of catamaran with a semisubmersible bow in wave
Autorzy:
Sun, H.
Jing, F.
Jiang, Y.
Zou, J.
Zhuang, J.
Ma, W.
Powiązania:
https://bibliotekanauki.pl/articles/258596.pdf
Data publikacji:
2016
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
SSB catamaran
model test
overset grid
motion region
motion response
Opis:
Compared with standard vessels, a slender catamaran with a semi-submerged bow (SSB) demonstrates superior seakeeping performance. To predict the motion of an SSB catamaran, computational fluid dynamics methods are adopted in this study and results are validated through small-scale model tests. The pitch, heave, and vertical acceleration are calculated at various wavelengths and speeds. Based on the overset grid and motion region methods, this study obtains the motion responses of an SSB catamaran in regular head waves. The results of the numerical studies are validated with the experimental data and show that the overset grid method is more accurate in predicting the motion of an SSB catamaran; the errors can be controlled within 20%. The movement data in regular waves shows that at a constant speed, the motion response initially increases and then decreases with increasing wavelength. This motion response peak is due to the encountering frequency being close to the natural frequency. Under identical sea conditions, the motion response increases with the increasing Froude number. The motion prediction results, that derive from a shortterm irregular sea state, show that there is an optimal speed range that can effectively reduce the amplitude of motion.
Źródło:
Polish Maritime Research; 2016, 1; 37-44
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Test research on the resistance performance of high-speed trimaran planing hull
Autorzy:
Ma, W.
Sun, H.
Zou, J.
Yang, H.
Powiązania:
https://bibliotekanauki.pl/articles/259708.pdf
Data publikacji:
2013
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
trimaran planing hull
side hulls
high speed
step
resistance
model test
Opis:
In order to identify high-speed navigation ability of trimaran planing hull, as well as investigate the characteristics of its resistance and hull form, ship model tests were conducted to measure resistance, trim and heaving under different displacements and gravity centre locations. The test results were then used to study the influence of spray strips on resistance and sea-keeping qualities. Moreover, different planning surfaces were compared in the model tests which helped to look into influence of steps on hull resistance and its moving position. Also, the resistance features of monohull and trimaran planing hulls, both with and without steps, were compared to each other. From the tests it can be concluded that: the two auxiliary side hulls increase aerodynamic lift at high-speed motion, which improves the hydrodynamic performance; the trimaran planing hull has also excellent longitudinal stability and low wave-making action; when Fr∇> 8, its motion is still stable and two distinct resistance peaks and two changes of sailing state (the second change is smaller) appear; spray strips are favourable for sea-keeping qualities at high speed. The change trends before the second resistance peak as to the resistance and sailing behaviour of trimaran planing hull without steps are the same as for monohull planing hull without steps. but when steps in both hulls exist the change trends are different; more specifically: trimaran planing hull with steps has only one resistance peak and its resistance increases along with its speed increasing, and the resistance is improved at the increasing speed as the number of steps increases.
Źródło:
Polish Maritime Research; 2013, 4; 45-51
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on dynamic response of offshore wind turbine structure under typhoon
Autorzy:
Li, Junlai
Wu, Weiguo
Wei, Yu
Shu, Yu
Lu, Zhiqiang
Lai, Wenbin
Jia, Panpan
Zhao, Cheng
Xie, Yonghe
Powiązania:
https://bibliotekanauki.pl/articles/32891255.pdf
Data publikacji:
2022
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
floating offshore wind turbine
structural dynamic response
typhoon
physical model test
Opis:
Floating offshore wind turbines are easily affected by typhoons in the deep sea, which may cause serious damage to their structure. Therefore, it is necessary to study further the dynamic response of wind turbine structures under typhoons. This paper took the 5MW floating offshore wind turbine developed by the National Renewable Energy Laboratory (NREL) as the research object. Based on the motion theory of platforms in waves, a physical model with a scale ratio of 1:120 was established, and a hydraulic cradle was used to simulate the effect of waves on the turbines. The dynamic response characteristics of offshore wind turbines under typhoons are systematically studied. The research results clarified that the turbine structure is mainly affected by wave loads under typhoons, and its motion response reaches its maximum value under the action of extreme wave loads. The research results of this paper can provide reference value for the design of offshore wind turbine structures under typhoons.
Źródło:
Polish Maritime Research; 2022, 1; 34-42
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A new six-DoF parallel mechanism for captive model test
Autorzy:
Lu, Yun
Wu, Jinbo
Li, Weijia
Wu, Yaozhong
Powiązania:
https://bibliotekanauki.pl/articles/1585037.pdf
Data publikacji:
2020
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
hydrodynamic coefficient
six DoF parallel mechanism
six component balance
captive model test
Opis:
In order to obtain the hydrodynamic coefficients that can save cost and meet the accuracy requirements, a new hydrodynamic test platform based on a 6DoF (six degrees of freedom) parallel mechanism is proposed in this paper. The test platform can drive the ship to move in six degrees of freedom. By using this experimental platform, the corresponding hydrodynamic coefficients can be measured. Firstly, the structure of the new device is introduced. The working principle of the model is deduced based on the mathematical model. Then the hydrodynamic coefficients of a test ship model of a KELC tank ship with a scale of 1:150 are measured and 8 typical hydrodynamic coefficients are obtained. Finally, the measured data are compared with the value of a real ship. The deviation is less than 10% which meets the technical requirements of the practical project. The efficiency of measuring the hydrodynamic coefficients of physical models of ships and offshore structures is improved by the device. The method of measuring the hydrodynamic coefficients by using the proposed platform provides a certain reference for predicting the hydrodynamic performance of ships and offshore structures.
Źródło:
Polish Maritime Research; 2020, 3; 4-15
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Model tests for shallow-water ship maneuverability in Three Gorges Reservoir
Autorzy:
Cai, C.
Cai, X.
Li, Y.
Powiązania:
https://bibliotekanauki.pl/articles/259922.pdf
Data publikacji:
2015
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
shallow-water test of ship model
simulated computation
maneuverability calibration
scale effect
Z shape test
K and T indexes
navigation safety
Opis:
This paper conducts calibration tests on the shallow-water maneuverability of 1:100 ship models for the typical navigation fleets in Three Gorges Reservoir. Major influential factors for the maneuverability similitude between models and prototypes and for scale effect were identified. A correction method for model scale was also established through model tests. Test results indicate that, by correcting the model scales of various fleets based on scale effect, the maneuverability indexes K’ (dimensionless of K) and T’ (dimensionless of T) of ship models are suitable for shallowwater tests, and properly reflect the maneuvering characteristics of prototypes. The findings provide an experimental basis for the navigation safety in Three Gorges Reservoir.
Źródło:
Polish Maritime Research; 2015, S 1; 136-140
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical simulations of hydrodynamic open-water characteristics of a ship propeller
Autorzy:
Felicjancik, J.
Kowalczyk, S.
Felicjancik, K.
Kawecki, K.
Powiązania:
https://bibliotekanauki.pl/articles/258544.pdf
Data publikacji:
2016
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
CFD
model tests
POW Test
propeller
validation
Opis:
The paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical simulations performed in the model and real scale. The results of numerical analyses performed in the model scale were confronted with those measured in the experiment. Then, making use of dimensionless coefficients which characterise propeller’s operation, the recorded model data were extrapolated to real conditions and compared with corresponding results of simulations. Both the numerical simulations and the experimental research were performed for the same propeller load states. The reported research is in line with other activities which aim at developing advanced numerical methods to.
Źródło:
Polish Maritime Research; 2016, 4; 16-22
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of model-scale open-water test uncertainty
Autorzy:
Król, Przemysław
Powiązania:
https://bibliotekanauki.pl/articles/32898216.pdf
Data publikacji:
2022
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
uncertainty
propeller open-water test
lifting surface method
model-scale experiment
propulsion
Opis:
Within the frame of CTO’s standard procedure, a propeller open-water test is preceded by a reference measurement, which is taken for a reference propeller model (P356). The results of these measurements are assembled to conduct an open-water test uncertainty analysis. Additional material was gathered from open-water tests that were conducted throughout several research projects on the CP469 model, which is a model of the Nawigator XXI propeller. The latter is a controllable pitch propeller; its pitch was reset before each test repetition. Known procedures for the determination of the open-water test uncertainty do not allow one to extract the manufacture impact directly, without building many models. This factor was addressed with the use of lifting surface calculations. Under certain additional assumptions, these calculations were performed for 100 generic versions of each propeller’s geometry, which were generated by random deviations from the theoretical data within the limits of allowed tolerances. The results of the conducted analyses made it possible to extract separate factors, which were connected to the test’s repeatability, measurement bias and geometry tolerance.
Źródło:
Polish Maritime Research; 2022, 4; 4-11
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-10 z 10

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies