Autor: Labuda, W. - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: The analysis of cutting tool geometric on cutting forces and surface roughness of steel applied to marine pumps shaft pins
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/246319.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
cutting forces
cutting temperature
surface roughness
stainless steal
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the research results referring to the analysis of the influence of finishing lathing on the cutting forces and surface roughness of stainless steel. The research was performed on a roller 60 mm in diameter made of X5CrNi18-10 steel. The finish tooling of pump shaft pins was carry out on a universal CDS 6250 BX-1000 centre lathe. The finish lathing process was carried out by means of Sandvik Coromant cutting tool with replaceable inserts. During the research, the effect of cutting tool geometric on cutting forces and surface roughness of steel applied to marine pumps shaft pins ware tested. In addition, the influence of cutting tool geometric on cutting temperatures was determined.
Źródło:: Journal of KONES; 2014, 21, 1; 147-152
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: The influence of cutting parameters on cutting forces and surface roughness
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/246880.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
cutting forces
cutting temperature
surface roughness
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the preliminary research results referring to the analysis of the influence of finishing lathing on the cutting forces and surface roughness of steel. The research was performed on a roller 39 mm in diameter made of S235JR steel. The finish tooling of pump shaft pins was carrying out on a universal centre lathe. The finish lathing process was carried out by means of a CCMT 09T304 PF Sandvik Coromant cutting tool with replaceable inserts. During the research, the effect of changes in the depth of cut on the value of cutting forces and temperature was defined. In addition, the influence of the depth of cut on the surface roughness was determined.
Źródło:: Journal of KONES; 2014, 21, 3; 199-204
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: The influence of changing of cutting parameters on temperature and cutting forces during turning process by CCET09T302R-MF insert
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/241601.pdf
Data publikacji:: 2018
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
temperature
cutting forces
cutting parameters
stainless steel
dynamometr
temperatura
siły skrawania
parametry cięcia
stal nierdzewna
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of change of cutting parameters on temperature and cutting forces during turning process of stainless steel. A shaft made of 304L stainless steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 centre lathes. Measurement of cutting forces during turning process used DKM 2010 turning dynamometer. A cutting tool conducted the turning process with CCET09T302R-MF insert by DIJET. During the turning, the following machining parameters were used: cutting speed Vc = 226 m/min, feed f = 0.044; 0.062; 0.083; 0.106 mm/rev and cutting depth ap = 0.375; 0.625; 0.875 mm. The chemical composition of steel was measured by Solaris-ccd plus optical spectrometer. The Smartzoom 5 microscope made the view of the nose radius of cutting tool.
Źródło:: Journal of KONES; 2018, 25, 1; 249-256
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: The influence of changing of cutting parameters on temperature and cutting forces during turning process of stainless steel with CCET09T302R-MF insert
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/243223.pdf
Data publikacji:: 2017
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
temperature
cutting forces
stainless steel
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of change of cutting parameters on temperature and cutting forces during turning process of stainless steel. A shaft made of 304L stainless steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 centre lathes. Measurement of cutting forces during lathing process used DKM 2010 turning dynamometer. The turning process was conducted by a cutting tool with CCET09T302R-MF insert by DIJET. During the turning, the following machining parameters were used: cutting speed Vc = 226 m/min, feed f = 0.044, 0.062, 0.083, 0.106 mm/rev and cutting depth ap = 0.25, 0.5, 0.75, 1.0 mm. The chemical composition of steel was measured by Solaris-ccd plus optical spectrometer.
Źródło:: Journal of KONES; 2017, 24, 4; 133-140
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: The influence of treatment conditions on cutting forces and surface roughness
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/241665.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
surface roughness parameter
stainless steel
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of treatment conditions during turning of shafts on the cutting forces and surface roughness parameter. A roller made of S235JR steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 and CU500MRD centre lathes. Measurement of cutting forces during lathing process used DKM 2010 and Kistler turning dynamometers. The turning process was conducted by a cutting tool with CCMT09T304 PF removable plate. During the turning, the following machining parameters were used: cutting speed Vc = 150 m/min, feed f=0.106 mm/rev and cutting depth ap = 0.5, 0.75, 1.0, 1.25, 1.5, 1.75 mm. The surface roughness was measured by T8000 profilometer.
Źródło:: Journal of KONES; 2016, 23, 1; 207-213
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: Finishing treatment of marine pump shafts made of X5CRNI18-10 steel
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/244602.pdf
Data publikacji:: 2018
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
temperature
cutting forces
stainless steel
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the results of influence of cutting parameters change on temperature and cutting forces during turning process of stainless steel. A shaft made of 304L stainless steel was used for the research. The cutting process was carried out on a universal CDS 6250 BX-1000 centre lathe. Measurement of cutting forces during lathing process used DKM 2010 turning dynamometer. The turning process was conducted by a cutting tool with CCET09T302R-MF insert by DIJET. During the turning, the following machining parameters were used: cutting speed Vc = 152, 219, 304 m/min, feed f = 0.044, 0.062, 0.083 mm/rev and cutting depth ap = 0.4, 0.8, 1.2, 1.6 mm. The view of the nose radius of cutting tool before and after the turning process was made by the Smartzoom 5 microscope.
Źródło:: Journal of KONES; 2018, 25, 2; 215-222
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: The influence of cutting inserts geometric on surface roughness of steel applied to sea water pump shafts
Autorzy:: Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/244988.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
surface roughness parameters
stainless steel
marine pump shaft
Opis:: One of the greatest problems of modern production techniques is the achievement of an appropriate quality at minimal costs and accompanied by the production efficiency increase. Therefore, while designing the production process, the technology used should have a considerable influence on the durability and reliability of machine parts to be produced. During finish treatment, the final dimensions as well as functional properties are imparted to a given element by application of proper treatment type. The engineer has a range of production techniques to choose for the proper surface layer formation. It is crucial to find a suitable solution which will meet the requirements as well as the work conditions of a given machine part. The article presents the research results of pump shaft pins finish turning. The research was performed on a roller 60 mm in diameter made of X5CrNi18-10 steel. The finish tooling of pump shaft pins was carry out on a universal CDS 6250 BX-1000 centre lathe. The finish lathing process was carried out by means of Sandvik Coromant cutting tool with replaceable inserts. In the research of lathing process used standard inserts (MF), inserts with increased tolerance (UM) and inserts with Wiper technology (WF). During lathing, the optimal machining parameters were used. The cutting process was performed at entering angle of 90°. The process of lathing used cutting tool dynamometer DKM 2010. During the research, the effect of cutting insert geometric and optimal cutting parameters on the surface roughness of steel applied to marine pumps shaft pins was determined.
Źródło:: Journal of KONES; 2015, 22, 3; 133-140
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: Experimental study on the influence of burnish parameters on the surface roughness reduction index
Autorzy:: Polanowski, S.
Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/247016.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: burnishing process
surface roughness parameter
stainless steel elements
Opis:: The paper presents the research results of relationship between surface roughness reduction index KRa and three input parameters: burnishing speed Vn, feed fn and burnishing force Fn., and all combinations of levels of yields N measured for 48 points of experiment. The experiment was repeated 3 times. In order to select the model describing the results of tests, the stepping approximation analysis was performed. It relayed at incorporated into the model in following steps approximation elements function, giving the biggest decrease of the sum of squared deviations. The first approximation was based on the ternary monomial of the powers from 0 to 3 for each input value. This approximation aim was to show, that the index of surface roughness reduction does not depend on the burnishing speed in the made in the area of research. The reduced input parameters to two, i.e. fn and Fn. The plan of the experiment was brought to N = 12 and M = 12. The best approximation of test results obtained in the case of Laurent polynomial with stepping selection of elements. The biggest contribution to the decrease in the sum of squared deviations was element −1 ∙ 3 , and then fn 2. The article shows that in the range fn {0.6:1.2} there was not information on the successful model and the lack of influence of f and Fn on the results of the experiment. It is postulated to retry the experiment for the feed f <0.6.
Źródło:: Journal of KONES; 2016, 23, 3; 395-402
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 9.

Tytuł:: The influence of finish tooling on friction properties of steel applied to sea water pump shafts
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/242888.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: plastic tooling
burnishing
stainless steel
angular momentum pump
riction properties
Opis:: Angular momentum pumps are very often applied on-board ships. These pumps are used in cooling circuits of medium and high power engines, power plant boilers as well as bilge, ballast and fire installations. Such an extensive use of angular momentum pumps on board is connected with their numerous advantages. However, during operation the wear of marine hull, the rotor and shaft seals take place. The research attempts to increase the service life of shafts. The article presents the research results referring to the analysis of the influence of finish treatment (finishing turning, grinding, burnishing) on the friction properties of steel applied to marine pump shafts. The research was performed on a roller 39 mm in diameter made of 304L stainless steel. The finish tooling of pump shaft pins was carry out on a universal centre lathe. The finish turning process was carried out by means of a WING WF 080408 Sandvik Coromant cutting tool with replaceable inserts. The grinding process was performed by grinding attachment for lathes. The 1 – 80x10x32 – 99C 80-N V grinding wheel was used for the process. The process of burnishing was done by SRMD single roll burnishing tool by Yamato. The burnishing process was carried out at the following technological parameters: burnishing force 1.1 kN, burnishing speed 35 m/min, feed 0.13 mm/rev. In addition, the influence of the number of burnishing tool passes on the friction was determined. The paper will present the research results of test on the friction properties examination of samples after finish machining. The experiment was performed on T-05 block-on-ring wear tester.
Źródło:: Journal of KONES; 2014, 21, 2; 185-192
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 10.

Tytuł:: The analysis of finishing tooling influence on corrosion properties researched by potentiodynamic method
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/246859.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: plastic tooling
burnishing
surface layers
angular momentum pump
corrosion properties
Opis:: Angular momentum pumps are very often applied onboard ships. These pumps are used in cooling circuits of medium and high power engines, power plant boilers and in bilge, ballast and fire installations. Very extensive use of angular momentum pumps on board is connected with their numerous advantages. During operation the wear of marine hull, the rotor and shaft seals take place. The research attempts to increase the service life of shafts. The article presents the research results referring to the analysis of the influence.. of finish treatment (lathing, grinding and burnishing) on the corrosion properties of steel applied to marine pump shafts. The research was performed on a roller of 40 mm in diameter made of X5CrNi 18-10 (AISI 304 L) stainless steel. The lathing process was carried out by means of a WNMG WF 080408 Sandvik Coromant cutting tool with replaceable inserts. The grinding process was performed by grinding attachment for lathes. The 1 - 80x10x32 - 99C 80-N V grinding wheel was used for the process. The process of burnishing was done by SRMD burnisher by Yamato. In addition, the influence of the burnisher passes number on the corrosion properties was determined. The paper will present the results of potentiodynamic research. To conduct the survey the Atlas 0531 EU and IA potentiostat will be used. Determination of parameters of the corrosion process will be executed on Elfit2 computer program.
Źródło:: Journal of KONES; 2012, 19, 2; 283-288
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 11.

Tytuł:: The analysis of finishing tooling influence on corrosion properties researched by EIS
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/248058.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: burnishing
surface layers
angular momentum pump
corrosion properties
EIS
Opis:: Angular momentum pumps are very often applied onboard ships. These pumps are used in cooling circuits of medium and high power engines, power plant boilers and in bilge, ballast and fire installations. Very extensive use of angular momentum pumps on board is connected with their numerous advantages. During operation the wear of marine hull, the rotor and shaft seals take place. The research attempts to increase the service life of shafts. The article presents the research results referring to the analysis of the influence of finish treatment (lathing, grinding and burnishing) on the corrosion properties of steel applied to marine pump shafts. The research was performed on a roller of 40 mm in diameter made of X5CrNi18-10 (AISI 304 L) stainless steel. The lathing process was carried out by means of a WNMG WF 080408 Sandvik Coromant cutting tool with replaceable inserts. The grinding process was performed by grinding attachment for lathes. The 1 - 80x10x32 - 99C 80-N V grinding wheel was used for the process. The process of burnishing was done by SRMD burnisher by Yamato. In addition, the influence of the burnisher passes number on the corrosion properties was determined. The paper will present the results of electrochemical impedance spectroscopy research. To conduct the survey the Atlas 0531 EU and IA potentiostat was used. Determination of the corrosion process parameters was performed computer programs: AtlasLab 2.0 and EIS Spectrum Analyzer.
Źródło:: Journal of KONES; 2012, 19, 1; 237-244
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 12.

Tytuł:: The analysis of influence on friction factor at constant force for marine pump shafts after finishing treatment
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/243518.pdf
Data publikacji:: 2013
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: plastic tooling
burnishing
stainless steel
angular momentum pump
friction factor
Opis:: Angular momentum pumps are very often used in cooling circuits of medium and high power engines, power plant boilers as well as bilge, ballast and fire installations. Such an extensive use of angular momentum pumps on board is connected with their numerous advantages. However during operation the wear of marine hull, the rotor and shaft seals takes place. The research attempts to increase the service life of shafts. The article presents the research results referring to the analysis of the influence of finish treatment (finishing turning, grinding, burnishing) on the friction factor of steel applied to marine pump shafts. The research was performed on a roller 39 mm in diameter made of 304L stainless steel. The finish tooling of pump shaft pins was carry out on a universal centre lathe. The finish turning process was carried out by means of a WNMG WF 080408 Sandvik Coromant cutting tool with replaceable inserts. The grinding process was performed by grinding attachment for lathes. The 1-80x10x32-99C 80-N V grinding wheel was used for the process. The process of burnishing was done by SRMD single roll burnishing tool by Yamato. The burnishing process was carried out at the following technological parameters: burnishing force 1.1 kN, burnishing speed 35 m/min, feed 0.13 mm/rev. In addition, the influence of the number of burnishing tool passes on the friction factor was determined. The paper aimed at defining the influence of burnishing on service conditions by: testing electrochemical corrosion, friction wear and contact fatigue. The work presented the research results of friction factor tests of the samples after finish turning, grinding and burnishing. In addition, the influence of the burnisher passes number on the friction factor was determined. The experiment was performed on block – roll tester machine.
Źródło:: Journal of KONES; 2013, 20, 2; 245-251
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 13.

Tytuł:: The influence of changing the side angle of the cutting tool by wiper technology on the value of material ratio parameters of steel applied to marine pump shaft pins
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/244335.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turning dynamometer
surface roughness
material ratio
stainless steal
Opis:: Angular momentum pumps are very often used in cooling circuits of medium and high power engines, power plant boilers as well as bilge, ballast and firefighting installations. Such an extensive use of angular momentum pumps on board is connected with their numerous advantages. However, during operation the wear of marine hull, the rotor and shaft seals take place. The research attempts to increase the service life of shafts. The article presents the research results of pump shaft pins after finish lathing. The research was performed on a roller 60 mm in diameter made of X5CrNi18-10 steel. The finish tooling of pump shaft pins was carried out on a universal CDS 6250 BX-1000 centre lathe. The finish lathing process was carried out by means of Sandvik Coromant cutting tool with replaceable inserts. In the research of lathing, process used inserts with Wiper technology. During the lathing, the optimal cutting parameters were used for inserts: CCMT09T302WF, CCMT09T304WF and CCMT09T308WF. The cutting process was performed at side angle of 90° ± 3°. The process of lathing used cutting tool dynamometer DKM 2010. During the research, the effect of cutting tool geometric on surface roughness parameter Ra of steel applied to marine pumps shaft pins was determined. The article presents the research results of material ratio parameters. In addition provides an examples shaft surface profile analysis and material ratio. Measurement of surface roughness and material ratio parameters was performed by T8000 profilometer.
Źródło:: Journal of KONES; 2015, 22, 2; 139-147
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 14.

Tytuł:: The analysis of finish tooling influence on wear intensity of marine pump shaft
Autorzy:: Labuda, W.
Charchalis, A.
Powiązania:: https://bibliotekanauki.pl/articles/244526.pdf
Data publikacji:: 2013
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: plastic tooling
burnishing
stainless steel
angular momentum pump
wear intensity
Opis:: Angular momentum pumps are very often applied onboard ships. These pumps are used in cooling circuits of medium and high power engines, power plant boilers as well as bilge, ballast and fire installations. Such an extensive use of angular momentum pumps on board is connected with their numerous advantages. However during operation the wear of marine hull, the rotor and shaft seals takes place. The research attempts to increase the service life of shafts The article presents the research results referring to the analysis of the influence of finish treatment (finishing turning, grinding, burnishing) on the friction of steel applied to marine pump shafts. The research was performed on a roller 39 mm in diameter made of 304L stainless steel. The finish tooling of pump shaft pins was carry out on a universal centre lathe. The finish turning process was carried out by means of a WNMG WF 080408 Sandvik Coromant cutting tool with replaceable inserts. The grinding process was performed by grinding attachment for lathes. The 1-80x10x32-99C 80-N V grinding wheel was used for the process. The process of burnishing was done by SRMD single roll burnishing tool by Yamato. The burnishing process was carried out at the following technological parameters: burnishing force 1.1 kN, burnishing speed 35 m/min, feed 0.13 mm/rev. In addition, the influence of the number of burnishing tool passes on the friction was determined. The paper will present the research results of test on the wear intensity examination of samples after finish machining. The experiment was performed on block – roll tester machine.
Źródło:: Journal of KONES; 2013, 20, 1; 163-170
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 15.

Tytuł:: The analysis of finish tooling influence on contact fatigue of steel applied to sea water pump shafts
Autorzy:: Charchalis, A.
Starosta, R.
Labuda, W.
Powiązania:: https://bibliotekanauki.pl/articles/242173.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: contact fatigue
burnishing
corrosion resistant steel
surface layer
angular momentum pumps
Opis:: The article presents the research results referring to the analysis of the influence of finish treatment (lathing, grinding, burnishing) on the contact fatigue of steel applied to marine pump shafts. The research was performed on a roller 25mm in diameter made of X5CrNi18-10 (AISI304 L) stainless steel. The lathing process was carried out by means of a Sandvik Coromant cutting too, the grinding was done by grinding attachment to a lathe, whereas the process of burnishing was performed by SRMD burnisher by Yamato. Within the research, the optimalization of burnishing technological parameters was conducted on account of the minimalization of Ra surface roughness coefficient as well as the maximalization of SU degree of surface layer relative hardness. The multi criteria optimalization conducted by min-max method with regard to minimum surface roughness as well as maximum degree of surface layer hardness demonstrated that burnishing process should be carried out at the following technological parameters: burnishing force 1.1 kN, burnishing speed 35 m/min, feed 0.13 mm/rev. In addition, the influence of the burnisher passes number on the surface layer quality was determined. It is essential for this research to determine the burnishing influence on the service conditions which comprises the electrochemical corrosion research, friction wear and contact fatigue research. The paper will present the research results of contact fatigue examination of samples after finish machining.
Źródło:: Journal of KONES; 2011, 18, 2; 85-92
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "Labuda, W." wg kryterium: Autor

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język