Wszystkie pola: combustion gases - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: Hydrogen rich gases combustion in the IC engine
Autorzy:: Szwaja, S.
Powiązania:: https://bibliotekanauki.pl/articles/245372.pdf
Data publikacji:: 2009
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: syngas
coke gas
hydrogen
combustion
Opis:: Experimental results of combusting three different syngases in an internal combustion (IC) spark ignition engine are presented in this paper. The syngases used for tests varied each from the other with hydrogen content, which was of 10,15 and 60%. Other combustible gases as CO and CH4 were also changed. Thus, the lower heating value of the syngases was of 2.7, 4.6 and 17.2 MJ/nm3, respectively. Combustion tests were performed at stoichiometric ratio of syngas-air mixture, with variable spark timing and constant compression ratio of 10. On the basis of in-cylinder combustion pressure histories the indicated mean effective pressure (IMEP) was computed and presented versus spark timing and vs location of the middle combustion phase expressed by the 50% of mass fraction burned (MFB). Additionally, the 0-10% MFB and 10-90% MFB were also determined. Furthermore, the paper contains theoretical determination of the three fuel quantities, which can affect combustion duration and heat release rate during burning the syngases in the IC engine. They are as follows: laminar flame speed, ignition delay and adiabatic flame temperature. Final results does not show satisfactory correlation between LFS computed at NTP and real combustion phasing. Furthermore, both long combustion duration and long 0-10% MFB leading to unstable combustion were observed for the syngas with the lowest LHV of 2.7 MJ/nm3.
Źródło:: Journal of KONES; 2009, 16, 4; 447-454
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: The influence of the shape of the combustion chamber on exhaust gases toxicity in T370 engine
Autorzy:: Kalina, P.
Kawalec, M.
Powiązania:: https://bibliotekanauki.pl/articles/243782.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: diesel engine
combustion chamber
geometry
toxicity
Opis:: An important issue in construction of combustion chamber in compression-ignition engines is proper selection of its shape and size. Both features are dependent on several factors such as fuel injector location and angle, spray atomizer selection (amount of holes, their diameter and angular position), location of inlet valve and air turbulence. By doing research on prototype engine T370, an analysis of influence of combustion chamber size and its modifications going towards lip construction on flue gas toxicity was done. The diameter and depth of combustion chamber was being changed while maintaining the same compression ratio. After that, a modification of tested combustion chambers was made by creating so called “lip”, which aim was to create a swirl of injected fuel in the vertical plane. To visualize the changes in swirl, a numerical analysis of fuel injection into combustion chamber was made. In discussed study, emission tests were performed according to ECE-R49. During the research six combustion chambers with diameters 60, 63 and 66 mm (and their modification) were investigated. Tests were performed for several types of injectors and different injection timing. However, for analysis of combustion chamber size the results are presented for the same injectors but with optimized injection timing.
Źródło:: Journal of KONES; 2015, 22, 2; 104-108
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Laser research of fuel atomization and combustion processes in the aspect of exhaust gases emission
Autorzy:: Jankowski, A.
Powiązania:: https://bibliotekanauki.pl/articles/243315.pdf
Data publikacji:: 2008
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engine
fuel preparation
combustion processes
fuel spray
ecology
Opis:: The fuel injection phenomena belongs to the most essential processes, which are object of many experimental and theoretical works, indispensable for development of contemporary internal-combustion engines, both the spark and compression ignition. The direct injection of fotel to the engine combustion chamber belongs to most advanced solutions and must realize at least two or even more different strategies of engine performance. Article presents the various research methods of the fuel atomization processes, being concentrated on laser methods, from which deserves on the emphasis the Particle Image Velocimetry (PIV) system, the Laser Doppler Velocimeter (LDV) system and Phase Doppler Particle Analyzer (PDPA) system. Article presents theoretical analysis relating the atomized fuel stream. The results of research based on the laser research equipment are also submitted in the article. Moreover presented are the results ofresearch of the combustion process in the fixed volume chamber, where essentially two different strategies of the combustion process of homogenous and heterogeneous load were realized. The properly shaped fuel stream permits on obtainment of repeatable ignition and combustion in the wide range of the mixture variance. The essential meaning has the fuel stream disintegration, which influences advantageously on the level of the toxic exhaust elements emission, particularly on the hydrocarbon emission level because of the ignition dropout elimination and on the level of the nitrogen oxides emission because of short sojourn time of the fuel droplets in the combustion zone.
Źródło:: Journal of KONES; 2008, 15, 1; 119-126
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: The influence of the size and shape of the “central body” of a combustion chamber on the toxicity of the exhaust gases in the Ursus 4390 engine
Autorzy:: Kalina, P.
Powiązania:: https://bibliotekanauki.pl/articles/246739.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engines
toxicity
combustion chamber
Opis:: This work is the third part of the articles published on the effects of the shape and position of the combustion chamber in piston compression diesel engines on the toxicity of exhaust gases. In two previous articles presented at the KONES 2015 conference, the impact of position of the combustion chamber in relation to position of the injector, and the influence of the shape of the chamber (diameter, depth, lip on the CO, HC and NOx emissions was analysed. In the current article, the shape of the “central body” in a combustion chamber is analysed. “Central body” is the protrusion located in the central part of a toroidal combustion chamber. Subsequent modifications to the basic combustion chamber consisted of reducing the size of this protrusion. The study involved four versions of combustion chambers. Modifications caused a slight decrease in the compression ratio, which could have an impact on the unambiguousness of the results, as the effect of changes in shape of the “central body”. However, to maintain a constant compression ratio would require a change in diameter or depth of the chamber cavity, which would obscure the obtained results with even greater impact. Emission tests in discussed study were performed according to ECE-R4. During the tests, the completion of the engine and the engine settings were not changed.
Źródło:: Journal of KONES; 2016, 23, 2; 171-176
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: An attempt of exhaust gases composition prediction in si engines powered by petrol and gaseous fuels
Autorzy:: Flekiewicz, M.
Kubica, G.
Flekiewicz, B.
Powiązania:: https://bibliotekanauki.pl/articles/245747.pdf
Data publikacji:: 2009
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: CNG
LPG
exhaust gases
SI engine
combustion analysis
Opis:: Optimization procedure of the si engines feeding systems requires the application of newer and more sophisticated tools, as an addition to well known but expensive experimental methods. Numerical methods can be considered nowadays as once playing the most important role in the combustion process analysis. Paper describes the application of the dual zone model, allowing the analysis of the combustion process in an SI engine with the possibility of estimating 10 different exhaust gases i.e.: CO2, CO, H2O O2, NO, N2, H2, H, O and OH. The research has been carried on a 1.6 litr es four cylinder SI engine, fed with petrol and alternatively with LPG and CNG. In-cylinder pressure for the 4th cylinder of the tested engine has been acąuired for several engine speeds. registered in-cylinder pressure traces p=p((fi), together with the volume variation nii=nii((fi) infunction ofcrank angle, were used in the combustion process simulating calculations. Obtained results made it possible to compare selected parameters describing the combustion process. Obtained results do also prove recognized fact related to the higher temperature necessary to initiate gaseous fuel combustion.
Źródło:: Journal of KONES; 2009, 16, 4; 105-113
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: Impact of an external, so called box, module on gases composition of the ROVER 2.0 CDTI engine
Autorzy:: Prajwowski, K.
Powiązania:: https://bibliotekanauki.pl/articles/244116.pdf
Data publikacji:: 2013
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engines
impact on power
torque
composition of the gases
chiptuning
Opis:: Environmental impact of the motor vehicle has been felt in every stage of the motor vehicle operation. In the initial phase of the operation, when the vehicle is new, the amount of pollutants getting into the environment is less than at the end of its life, before the scrapping. This is connected with wearing the engine during its operation. However, the need for better performance through the chiptuning or the Box type devices are quite common nowadays, but the impact on the environment may not exceed the permitted emission limits. The article describes the external, so-called Box, module and its impact on the change of the injector opening time, and also on the change of the ROVER 2.0 CDTi engine power and torque. The simplicity of this device lies in the fact that such a modification can be made by everyone who follows the installation instructions. It is not necessary to conduct the program reading, like in the case of a program exchange in the EEPROM or programming via the diagnostic connector EOBD. The external module (box) is connected between the ECU and the Common Rail injectors. Thus, the control program does not change, but the injector opening time is adequately increased.
Źródło:: Journal of KONES; 2013, 20, 3; 323-329
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: Simulation of exhaust gases components formation in engine working with combustion initiation from ignition dose of fuel
Autorzy:: Sendyka, B.
Mitianiec, W.
Noga, M.
Powiązania:: https://bibliotekanauki.pl/articles/242242.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: modelling
simulation
spark ignition
compression ignition
exhaust gases emission
Opis:: The paper deals with problems of model analysis of the process of exhaust gases components formation in internal combustion engine working with combustion initiation from ignition dose of fuel injected directly into the working space. In result of scientific-research works carried out in the Chair of Internal Combustion Engines of Cracow University of Technology on the basis of a four stroke engine a driving unit was elaborated which may work both with spark ignition and combustion initiation from a ignition dose of fuel. Application of two combustion systems in engine aimed at combining the advantages of spark ignition with compression ignition driving units. Such an engine is characterized by fuel consumption comparable with that gained by compression ignition engines, whereas, the exhaust gases composition is similar to that occurring in up-to-date spark ignition engines. Similar assumption concern the Homogenous Charge Compression Ignition - HCCI system which seems to be a future solution of internal combustion engines, nevertheless, up till now, in spite of intensive works in many countries all over the world, one did not succeed to control the combustion process in a large range of rotational speeds and loads what would give the possibility of using it in traction application. The solution proposed in the patent application by Prof. B. Sendyka is not burdened with this drawback since the moment of occurrence of volumetric ignition of the formed mixture in the process of filling is tightly connected with the moment of fuel dose injection. In result of simulative studies carried out by use of KIVA-3V software on the discussed solution it was stated that the process of exhaust gases toxic components formation in engine working in the mode of ignition from pilot dose does not depart in generally form from that which occurs at work with spark ignition.
Źródło:: Journal of KONES; 2011, 18, 2; 391-396
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: Diesel engines with respect to Euro 6 and Bin5/Lev II emission limits
Autorzy:: Brzeżański, M.
Powiązania:: https://bibliotekanauki.pl/articles/247277.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engines
emission of toxic components of exhaust gases
Opis:: The article presents future requirements concerning emission of toxic components of exhaust gases valid for Diesel engine passenger cars. Questions connected with fulfilment of these standards were discussed. Chosen structural solutions permitting fulfilment of future requirements concerning emission were presented. In Europe passenger cars equipped with Diesel engines which get the homologation certificate for the first time the emission limit determined by the standard Euro 6 will be binding from year 2014. The relation to the at present binding limit Euro 5 emission of nitric oxides, the sum of hydrocarbons and nitric oxides as well as emission of particulate matter must be reduced. On the European market use could be made of experience gained during exploitation heavy duty vehicles in which decrease in nitric oxides emission is achieve by means of selective catalytic reduction (SCR). A more complex system of emission appraisal is valid in USA and especially in the states where the so called Californian standards were adopted. On the example of Volkswagen 2.0 TDI engine it was shown that in modern constructions of combustion engines there is still a large developmental potential. In this case the development went in the direction of fulfilment of new very requiring standards of emission of toxic components of exhaust gases. Well known in Europe 2.0 TDI engine which in its new version fulfils the most strict emission standards BIN5/LEV II constitutes the structural basis of the drive unit designed for the American market. Under such conditions the firm Volkswagen belongs to the small number of cars producers who for a couple of year have offered with success, passenger cars equipped with Diesel engines.
Źródło:: Journal of KONES; 2011, 18, 4; 33-40
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 9.

Tytuł:: Possibilities of changes of parameters of the driver to engine Fiat 1.3 JTD performances
Autorzy:: Prajwowski, K.
Powiązania:: https://bibliotekanauki.pl/articles/247158.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engines
impact on power
torque
composition of the gases
chiptuning
Opis:: The aim is to present possible ways of interference in the factory engine control program and the impact of what you want changes made changes on engine performance. This objective has been completed on the basis of the programme steering engine Fiat 1.3 MultiJet engine compartment is fitted on the chassis in the Faculty at Motor Vehicles Exploitation. Methods of reading logic. The activity and the construction of an electronic control circuit. Discusses the operation and construction of an electronic control. Shows the selected map control for driver, sample modifications and their impact on power, torque and the composition of the gases. The main assumption during modification of the factory driver software controlling Fiat 1.3 JTD engine was to increase torque within the low range of rotational speeds. The range of modifications had the task of evaluating the software methodology, changes in driver parameters and they effect on engine performance only. The obtained results are evidence of the correctness of modifications carried out within injection dose and supercharging pressure. Hexadecimal notation values and decimal notation values corresponding to them, modified bitmap for pilot injection dose, original bitmap values for pilot injection dose time, modified bitmap values for injection dose time, modified bitmap for main injection dose, original bitmap for supercharging pressure, original bitmap for supercharging pressure delimiter, comparison of external characteristic curve are presented in the paper.
Źródło:: Journal of KONES; 2011, 18, 4; 389-396
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 10.

Tytuł:: Catalytic properties analysis of platinum catalytic converters in self ignition engine exhaust gases
Analiza właściwości katalitycznych reaktorów platynowych do silników o zapłonie samoczynnym
Autorzy:: Kruczyński, S. W.
Kamela, W.
Mleczko, P.
Powiązania:: https://bibliotekanauki.pl/articles/244197.pdf
Data publikacji:: 2008
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: silniki spalinowe
emisja substancji szkodliwych
reaktory katalityczne
zanieczyszczenie środowiska
combustion engines
toxic gases emission
catalytic reactors
air pollution
Opis:: In this article the catalytic properties comparison of four different platinum catalytic converters working in exhaust gases of self ignition engine were described. The test procedure and the test bench were described. Article contains structure of tested catalytic converters with physicochemical investigations of their active surface. The reactors surfaces views from scanning electron microscope (SEM) and x-ray surface structure investigations were also included. Comparison of tested catalytic converters properties were made in function of their temperature. Analyses were related to rector's ability to convert carbon monoxide, hydrocarbon, sum of nitric oxides, nitrogen monoxide and nitrogen dioxide. Results of investigations have shown that platinum catalytic converters working in diesel exhaust gases have high efficiency in oxidation of nitrogen monoxide to nitrogen dioxide. This property is mainly used in continuous regeneration trap systems (CRT). Catalytic converters ability to passive reduction of nitric oxides by use of hydrocarbons was demonstrated. Ranges of tested reactors temperature in which their properties that can be used in continuous regeneration trap systems and systems of selective nitric oxides reduction by use of hydrocarbons (HC-SCR) were defined. Mentioned reactors properties were estimated in connection to platinum load on reactors surface.
W artykule przedstawiono porównanie właściwości katalitycznych czterech reaktorów platynowych o różnym ładunku platyny pracujących w spalinach silnika o zapłonie samoczynnym. Artykuł zawiera opis stanowiska badawczego oraz procedurę badań. W pracy przedstawiona została budowa badanych modeli reaktorów katalitycznych i badania fizykochemiczne ich powierzchni aktywnych, w tym obrazy ze skaningowego mikroskopu elektronowego (SEM) oraz badania rentgenowskie struktury powierzchni. Porównania właściwości badanych reaktorów katalitycznych dokonano w funkcji temperatury ich pracy. Analiza dotyczyła zdolności reaktorów do konwersji tlenku węgla, węglowodorów, sumarycznego stężenia tlenków azotu, tlenku azotu oraz dwutlenku azotu. Wyniki badań wykazały, że reaktory platynowe pracujące w spalinach silnika o zapłonie samoczynnym wykazują dużą efektywność w utlenianiu tlenku azotu do dwutlenku azotu. Właściwość ta jest w szczególności wykorzystywana w systemach ciągłej regeneracji filtra cząstek stałych (CRT).Wykazano również zdolność tych rektorów do pasywnej redukcji tlenków azotu za pośrednictwem węglowodorów. Określono zakres temperatury pracy badanych reaktorów, przy których ujawniają się ich właściwości katalityczne możliwe do wykorzystania w systemach ciągłej regeneracji filtra cząstek stałych i systemach selektywnej redukcji tlenków azotu węglowodorami (HC-SCR). Oceniono wyżej wymienione właściwości reaktorów badawczych w zależności od ładunku platyny naniesionego na ich powierzchnię.
Źródło:: Journal of KONES; 2008, 15, 2; 247-256
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 11.

Tytuł:: Examinations of the influence of heating up the catalytic reactor on the toxic exhaust gases component emission during a cold start-up
Autorzy:: Koliński, K.
Powiązania:: https://bibliotekanauki.pl/articles/244128.pdf
Data publikacji:: 2009
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engines
engine start-up
emission
catalytic reactor
Opis:: This article presents the results of the tests of catalytic reduction of carbon oxide and hydrocarbon emission during the self-ignition engine start-up. The tests were performed at the station in the climate chamber at lowered ambient temperatures: -7 ,-15 and -20 °C. A heated three-function platinum-palladium catalytic reactor with a metal monolith was used in the tests. The test methodology included a measurement of toxic exhaust gases concentration upstream and downstream the catalytic reactor at simultaneous measurement of the start-up parameters and measurement of temperatures in selected engine and catalytic reactor locations. A period of the cold engine start-up is characterized by a relatively high carbon oxide and hydrocarbon emission. The level of that emissions increases as the ambient temperature gets lower. As a result of the tests the influence of heating up the reactor on its operation during the self-ignition engine start-up was identified. Carbon oxide and hydrocarbon emission during the start-up period can be reduced by initial heating up the catalytic reactor before the start-up by means of an electric heater. When heating up the reactor surface up to 40°C at ambient temperature of-7°C, CO concentration can be reduced by 60...80% and the hydrocarbon concentration can be reduced by app. 60% on the average.
Źródło:: Journal of KONES; 2009, 16, 1; 255-264
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 12.

Tytuł:: Impact of an external, so called box, module on power and torque of the fiat 1.3 JTD motor
Autorzy:: Prajwowski, K.
Powiązania:: https://bibliotekanauki.pl/articles/248034.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion engines
impact on power
torque
composition of the gases
chiptuning
box
Opis:: With the emergence of vehicles equipped with fuel injection systems with EDC electronic control system (Electronic Diesel Control) on the market, there appeared opportunity to make changes within the factory program of engine control management. This enables precise and differentiated shaping of the course of combustion. With the gradual development of the EDC different methods of intervention in the engine control program appeared, including exchange of the program in the EEPROM, connecting the external modules, so called Boxes, and programming via the EOBD diagnostic connector (European On Board Diagnosis). The article presents the external module, so-called Box and its impact on the variation in pressure in the Common Rail high pressure cell, and also on the power change and torque of the Fiat 1.3 JTD MultiJet engine. It is both the simplest and least effective method of increasing vehicle performance. Its simplicity lies in the fact that such a modification may be made by anyone who follows the installation instructions. There is no need to carry out program reading like in the event of program exchange in the EEPROM or programming by the EOBD diagnostic connector. The external module (box) is connected between the EDC and the fuel pressure sensor in the Common Rail cell. Thus, the control program does not change, but it is "cheated" by the module forcing from the EDC other values of signals controlling the actuators.
Źródło:: Journal of KONES; 2012, 19, 1; 327-332
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 13.

Tytuł:: Influence of spark ignitrion engine warm up process on toxic gases conversion in three way catalyst
Wpływ procesu rozgrzewania się silnika o zapłonie iskrowym na konwersję substancji szkodliwych w trójfunkcyjnym reaktorze katalitycznym
Autorzy:: Kruczyński, S.
Danilczyk, W.
Kamela, W.
Powiązania:: https://bibliotekanauki.pl/articles/247879.pdf
Data publikacji:: 2007
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: silniki spalinowe
emisja substancji szkodliwych
reaktory katalityczne
zimny rozruch silnika
zanieczyszczenie środowiska
combustion engines
toxic gases emission
catalytic reactors
engine warm up process
air pollution
Opis:: In his article the influence of deactivated three way catalyst on toxic gases conversion at engine warm up process was described. The test procedure and the test bench were described. The test bench was used to achieve catalytic reactor deactivation at laboratory conditions. The test procedure was chosen to achieve catalytic reactor deactivation same as at the real road conditions at the vehicle that traveled 100 000 kilometers. Paper contains results of toxic gases conversion at the new and deactivated reactors. This was made to estimate the influence of catalytic reactor aging on toxic gases conversion ability. Article also contains the results of toxic gases emission measured at the NEDC test. This measurement was also done with new and aged reactor mounted at the chosen vehicle exhaust pipe. Results from this test was used to estimate CO, HC and NOX conversion at aged catalytic reactor at the engine warm up process in all NEDC test cycles. Received results shown that toxic gases conversion at deactivated reactor decreases at range from 14 to 32% depending on chosen toxic substance. Examples of O2, CO2 and CO HC i NOX concentrations changes after catalyst at NEDC test, the CO, HC and NOX conversion changes In function of catalytic process temperature for New and deactivated catalysts, comparison of CO, HC and NOX conversion received at NEDC test and from simulation for new catalyst are presented in the paper.
W artykule przedstawiono wpływ obecności w układzie wydechowym pojazdu deaktywowanego reaktora katalitycznego na spadek konwersji substancji szkodliwych podczas zimnego rozruchu silnika. Opisano metodę oraz stanowisko hamowniane służące do deaktywowania reaktora katalitycznego na hamowni silnikowej. Przedstawiona metoda pozwoliła na deaktyację reaktora odpowiadającą przebiegowi 100 000 kilometrów w rzeczywistych warunkach eksploatacji reaktora katalitycznego w pojeździe. Przedstawiono wyniki pomiarów konwersji związków toksycznych w reaktorze nowym oraz po teście deaktywacji w celu określenia wpływu starzenia reaktora katalitycznego na jego zdolność do konwersji substancji szkodliwych. W artykule zamieszczono również wyniki badań uzyskane w trakcie pomiarów emisji substancji szkodliwych na hamowni podwoziowej, w teście NEDC pojazdu z nowym oraz deaktywowanym reaktorem katalitycznym. Określono konwersję CO, HC oraz NOx za deaktywowanym reaktorem umieszczonym w pojeździe, w trakcie rozgrzewania się silnika, w kolejnych fazach testu NEDC. Uzyskane wyniki wykazały spadek konwersji substancji szkodliwych, za daktywowanym reaktorem katalitycznym w zakresie od 14 do 32% w zależności od wybranego związku toksycznego. W artykule są zilustrowane przykładowe zmiany stężeń O2, CO2, CO, HC oraz NOx za reaktorem katalitycznym pojazdu w teście NEDC, zmiana konwersji CO, HC oraz NOx w funkcji temperatury pracy reaktora katalitycznego nowego oraz deaktywowanego, porównanie konwersji NOx uzyskanych w teście NEDC oraz w trakcie badań symulacyjnych nowego reaktora katalitycznego.
Źródło:: Journal of KONES; 2007, 14, 3; 319-329
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 14.

Tytuł:: Effect to the fuel system type on energy, economic and environmental indicators of the spark-ignition engine work
Autorzy:: Ambrozik, A.
Ambrozik, T.
Kurczyński, D.
Łagowski, P.
Jankowski, R.
Kowalczyk, W.
Powiązania:: https://bibliotekanauki.pl/articles/245062.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: vehicles
combustion engines
fuel supply system
emission of exhaust gases
Opis:: The paper presents selected results of tests on the Fiat Panda I car powered by 1.2 dm3 spark ignition engine. The engine had production installed fuel system with the single-point petrol injection. To improve its in-service performance, the engine was fitted with the multi-point injection fuel system. The assessment of the indicators of the work of the engine, fitted with single-point, or alternatively, multi-point injection fuel system, was conducted on the basis of the tests performed on the MAHA chassis dynamometer. First, tests were run for single-point injection fuel system. Next, the same tests were performed when the engine was fitted with the multi-point injection fuel system. In the tests, engine power, torque, fuel consumption and the concentrations of the exhaust gas components were measured. The latter included carbon monoxide CO, carbon dioxide C02, hydrocarbons HC, nitrogen oxides NOx, and oxygen 02. AVL Digas 4000 exhaust gas analyser was used to take measurements of the concentrations of the basic components of the exhaust gas and of the excess air ratio %u03BB. The investigations were conducted by performing the inertia test and by using the dynamometer to determine the basic indicators of the engine operation. In the investigations, the crankshaft rotational speed ranged from 1500 to 6500 rpm with 500 rpm step. The experimental results made it possible to evaluate how the manner and site of fuel delivery affect the engine -work indicators.
Źródło:: Journal of KONES; 2014, 21, 3; 7-14
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 15.

Tytuł:: Affect of change of regulating parameters on course of external surface characteristics of unitary fuel consumption and exhaust gases smokiness of JK type engine supplied with RME
Wpływ zmiany parametrów regulacyjnych na przebieg zewnętrznych charakterystyk powierzchniowych jednostkowego zużycia paliwa i zadymienia spalin silnika typu JK zasilanego RME
Autorzy:: Stoeck, T.
Borodyn, A.
Powiązania:: https://bibliotekanauki.pl/articles/242727.pdf
Data publikacji:: 2007
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: transport
silniki spalinowe
paliwa roślinne
zużycie paliwa
zadymienie spalin
transportation
combustion engines
vegetable fuels
fuel consumption
exhausts gases smokiness
Opis:: An intensive expansion of motorization caused a necessity to limit its harmful acting on the environment. It is connected with more and more law requirements and regulations from the range of protection of the natural environment. The essential part in this process is played by vegetable fuel like rape oil methyl group ester of higher fatty acids, more and more often used to supply Diesel engines. The most essential problem for these drive units in the ecological aspect is the smokiness level, it means the soot contents in exhaust gases. Using this kind of vegetable fuels seems to be reasonable, especially in case of older construction engines, for which introducing of other solutions could be troublesome and unjustified. In this lecture there has been discussed affect of change of factory settings of the unitary fuel consumption and exhaust gases smokiness of the engine with the turbulence combustion chamber supplied with RME. The parameters adjusted in relation to the nominal settings were: injection pressure, the injection advance angle and injection pump volumetric fuel charge. The results of the tests have been shown in the form of the external surface characteristics of the engine tested.
Intensywny rozwój motoryzacji spowodował konieczność ograniczenia jej szkodliwego działania na otoczenie. Związane jest to z coraz ostrzejszymi wymaganiami i regulacjami prawnymi z zakresu ochrony środowiska naturalnego. Istotną rolę w tym procesie odgrywają paliwa roślinne takie jak ester metylowy wyższych kwasów tłuszczowych oleju rzepakowego, który coraz częściej stosuje się do zasilania silników z zapłonem samoczynnym. W aspekcie ekologicznym najistotniejszym problemem dla tych jednostek napędowych jest poziom zadymienia czyli zawartości sadzy w spalinach wylotowych. Stosowanie paliw roślinnych tego rodzaju wydaje się być uzasadnione szczególnie w przypadku silników starszych konstrukcji, dla których wprowadzenie innych rozwiązań mogło by być kłopotliwe oraz ekonomicznie nieuzasadnione. W niniejszym referacie omówiono wpływ zmiany nastaw fabrycznych na jednostkowe zużycie paliwa i zadymienie spalin silnika z komorą wirową spalania zasilanego RME. Parametrami regulowanymi w stosunku do ustawień nominalnych były: ciśnienie wtrysku, kąt wyprzedzenia wtrysku i objętościowa dawka paliwa pompy wtryskowej. Wyniki badań przedstawiono w formie powierzchniowych charakterystyk zewnętrznych badanego silnika.
Źródło:: Journal of KONES; 2007, 14, 4; 471-477
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "combustion gases" wg kryterium: Wszystkie pola

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język