Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "road vehicle" wg kryterium: Temat


Wyświetlanie 1-10 z 10
Tytuł:
Research of ecological indicators of two-way vehicle in stationary conditions
Autorzy:
Kamińska, Michalina
Andrzejewski, Maciej
Daszkiewicz, Paweł
Powiązania:
https://bibliotekanauki.pl/articles/2097608.pdf
Data publikacji:
2022
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
exhaust emission
rail-road vehicle
NRSC
PEMS
NRMM
emisja spalin
pojazd szynowy
Opis:
The presented article concerns the research on the emission of pollutants of a rail-road tractor in two stationary research tests. The purpose of the tests was to carry out control tests of pollutant emissions and their analysis. The object used during the works was approved in accordance with the Stage V standard, which requires measurements of emissivity both in stationary, dynamic and real conditions. Despite the requirement to test engines installed on a vehicle during their normal duty cycle with PEMS, the emission limits measured in this test have not yet been defined. Therefore, the work below focuses on the stationary test cycle. The measurements were carried out in accordance with the internal combustion engine operating points described in the approval test, and then compared with the modernized NRSC test. It contains modified measuring points and rotational speeds of the crankshaft, adopted on the basis of the most common operating parameters of agricultural tractor combustion engines in real operating conditions. The measurements were performed with the use of a mobile dynamometer and devices for measuring emissions of harmful exhaust gas compounds and recording on-board data. In the performed test, the vehicle drive system worked at fixed operating points, with defined values of crankshaft rotational speed and load. Based on the recorded data on the concentrations of pollutants in the exhaust gases, the unit emission of the tested object was determined. In the final stage of the work, these data were used to perform a comparative analysis with the emission limits contained in the standard.
Źródło:
Combustion Engines; 2022, 61, 1; 30--34
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
PEMS-based investigations into exhaust emissions from non-road and rail vehicles
Autorzy:
Merkisz, J.
Lijewski, P.
Pielecha, J.
Powiązania:
https://bibliotekanauki.pl/articles/133787.pdf
Data publikacji:
2016
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
non road vehicle
rail vehicles
pollution emissions
real driving emissions
portable emission measurement system
pojazd pozadrogowy
pojazdy szynowe
emisje zanieczyszczeń
rzeczywista emisja cząstek
przenośne systemy pomiaru emisji
Opis:
At the beginning of the twenty-first century, one of the major challenges of humanity was to reduce the negative effects of civilization development. Besides the engines used in road vehicles there is a large group of engines for non-road applications. This group includes motor propelled vehicles not used on the road NRMM (Non-Road Mobile Machinery). Engines of these vehicles, among all of the non-road applications, are characterized by very specific working conditions that do not allow for them to be qualified for propulsion engines. The main problem with these vehicles is the particulate matter and nitrogen oxides emission. Rail vehicles operating conditions these requirements take by the similar way, as having a wide range of rolling stock markedly alters the environmental impact of these vehicles. Thus it becomes necessary to consider the issue of the method of evaluation of engine emissions in rail vehicles in terms of their actual operating conditions. Thus, efforts to assess the actual level of emissivity for rail vehicles and attempts to improve it are necessary and justified.
Źródło:
Combustion Engines; 2016, 55, 3; 46-53
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Issues of emission evaluation of road-rail vehicles in the aspect of current type approval regulations
Autorzy:
Daszkiewicz, Paweł
Rymaniak, Łukasz
Kamińska, Michalina
Powiązania:
https://bibliotekanauki.pl/articles/133365.pdf
Data publikacji:
2019
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
engine exhaust emission
road-rail vehicle
fuel consumption
research in real conditions
ecology
emisja spalin z silnika
pojazd szynowo-drogowy
zużycie paliwa
badania w warunkach rzeczywistych
ekologia
Opis:
One of the ways to reduce exhaust emissions from vehicles is to replace worn-out shunting locomotives with road-rail tractors. The main purpose of this solution is to reduce the negative environmental impact of the vehicle and to reduce the fuel consumption compared to a shunting locomotive performing the same work. The tests on exhaust emissions of rail vehicles are carried out on an engine test bench, making it impossible to determine the environmental performance of these vehicles during real operation. Therefore, it is advisable to carry out measurements in real operating conditions in order to obtain reliable reference results. This enables the verification of vehicles ecological indicators in a wide range of operational work parameters. It is possible to obtain reliable results regarding the impact of the tested vehicle on the natural environment in this way and compare them with the applicable emission standards.
Źródło:
Combustion Engines; 2019, 58, 3; 269-273
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of the operation of the hybrid drive system in the light of the proposed Euro 7 standard
Autorzy:
Szramowiat, Mateusz
Szałek, Andrzej
Powiązania:
https://bibliotekanauki.pl/articles/2097580.pdf
Data publikacji:
2021
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
hybrid drive system
real driving emissions
Euro 7 standard
vehicle road tests
hybrydowy układ napędowy
rzeczywista emisja cząstek
standard Euro 7
badania drogowe pojazdów
Opis:
The article presents the issues of energy recovery in the hybrid drive system of a vehicle. Road tests of a vehicle equipped with a hybrid powertrain were carried out in accordance with the recommendations of the RDE test. In these studies, measurements of braking energy recovery were carried out in urban, rural and motorway traffic conditions. The analysis of the obtained test results may constitute a premise for the creation of an appropriate strategy for the operation of the hybrid drive system in terms of meeting the requirements of the currently prepared Euro 7 standard.
Źródło:
Combustion Engines; 2021, 60, 4; 65--68
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of the driving speed on the exhaust emissions
Wpływ prędkości jazdy samochodem na emisję spalin
Autorzy:
Merkisz, J.
Jacyna, M.
Andrzejewski, M.
Pielecha, J.
Merkisz-Guranowska, A.
Powiązania:
https://bibliotekanauki.pl/articles/133473.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
road tests
exhaust emissions
vehicle speed
badania drogowe
emisja spalin
prędkość jazdy
Opis:
The aim of the study is to verify the thesis about the influence of the vehicle speed on the exhaust emissions. The influence of the speed on the fuel consumption is quite easily measurable and generally possible to identify, while determining the emissions of harmful substances requires specialized research equipment. The analysis is important from the point of view of the vehicle operation. The paper presents the results of the road tests of a car fitted with a diesel engine. It contains the results of measurements of the concentration of the exhaust components. In the measurements, PEMS portable equipment was used. The study was conducted under actual traffic conditions (motorway driving) on a selected portion of the A2 motorway, located near Poznan.
W artykule przedstawiono wyniki badań, których celem było zweryfikowanie tezy o wpływie prędkości jazdy samochodem na emisję spalin. Wpływ prędkości jazdy na przebiegowe zużycie paliwa jest łatwo mierzalny i powszechnie możliwy do określenia, natomiast w celu określenia emisji substancji szkodliwych należy posłużyć się specjalistyczną aparaturą badawczą. Przeprowadzono analizę, która jest istotna z punktu widzenia ekologii eksploatacji pojazdów samochodowych. Zaprezentowano wyniki badań drogowych samochodu osobowego napędzanego silnikiem o zapłonie samoczynnym. Artykuł zawiera także wyniki pomiarów stężenia podstawowych związków szkodliwych emitowanych ze spalinami przez silnik tego pojazdu. W pomiarach wykorzystano mobilną aparaturę do badań toksyczności spalin typu PEMS. Badania przeprowadzono w rzeczywistych warunkach ruchu samochodu (jazda autostradowa) na wybranym fragmencie autostrady A2, zlokalizowanym w rejonach Poznania.
Źródło:
Combustion Engines; 2014, 53, 1; 41-47
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The research of exhaust emissions and fuel consumption from HHD engines under actual traffic conditions
Badania emisji związków toksycznych spalin i zużycia paliwa z silników HDD w warunkach ruchu drogowego
Autorzy:
Merkisz, J
Fuć, P.
Lijewski, P.
Ziółkowski, A.
Rymaniak, Ł.
Powiązania:
https://bibliotekanauki.pl/articles/133609.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
heavy-duty vehicle
exhaust emissions
road tests
pojazd ciężki
emisja gazów wylotowych
badania drogowe
Opis:
The paper presents a comparative analysis of the emission of CO, NOx, CO2 and gas mileage for two heavy-duty long haulage vehicles. The tests were performed on the same test road. The test route reflected typical daily operation of heavy-duty vehicles – a drive to the loading/unloading zone and cruise on national roads. In the investigations, the authors used a portable exhaust emissions analyzer (SEMTECH DS, PEMS – Portable Emissions Measurement System). Based on the performed analysis, optimum engine was selected for long haulage vehicles under conditions of Polish transport and logistic infrastructure in terms of fuel consumption.
W artykule przedstawiono porównanie emisji CO, NOx, CO2 oraz przebiegowego zużycia paliwa dla dwóch pojazdów ciężkich przeznaczonych do długodystansowego przewozu towarów. Badania wykonano na tym samym odcinku pomiarowym. Odzwierciedlał on codzienną eksploatację pojazdów ciężkich – dojazd do miejsca załadunku/rozładunku i ruch po drogach krajowych. Do badań wykorzystano mobilny przyrząd SEMTECH DS z grupy PEMS (Portable Emissions Measurement System). Na podstawie przeprowadzonej analizy określono właściwy wybór silnika spalinowego pojazdu ciężkiego w aspekcie zużycie paliwa dla długodystansowego przewozu towarów w warunkach reprezentujących krajową infrastrukturę transportowo-logistyczną.
Źródło:
Combustion Engines; 2014, 53, 3; 56-63
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of vehicle body roll angle on the motion stability and maneuverability of the vehicle
Autorzy:
Parczewski, K.
Wnęk, H.
Powiązania:
https://bibliotekanauki.pl/articles/133587.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
stability of vehicle motion
suspensions
interaction of the road and tires
roll angle of vehicle body
stabilność ruchu pojazdu
zawieszenie
interakcja drogi i opon
Opis:
The article discusses the impact of design solutions of vehicle suspensions into angles of body roll. It was shown which type of suspensions is better from this point of view. There were examined the dependence of the suspensions parameters on the vehicle body roll angle. The influence of camber angle on the force transmitted to the tire contact with the road surface was analysed. The lateral forces were measured on the test stand. There was tested dependency of lateral forces from the sideslip angle for different angles of camber. Was analysed change of lateral forces generated by camber angle on the vehicle which was made on a scale ~ 1:5 during tests carried out on the testing track. For this purpose, two tests have been selected: first one allowing the measurement in steady motion conditions, the second one with dynamic change of direction of vehicle motion. The graphs show the effect of camber angles on the controllability and stability of the vehicle motion.
Źródło:
Combustion Engines; 2017, 56, 1; 133-139
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Energy consumption of a passenger car with a hybrid powertrain in real traffic conditions
Autorzy:
Bieniek, Andrzej
Graba, Mariusz
Mamala, Jarosław
Prażnowski, Krzysztof
Hennek, Krystian
Powiązania:
https://bibliotekanauki.pl/articles/2202524.pdf
Data publikacji:
2022
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
energy consumption
hybrid vehicle
road tests
energy consumption analysis
zużycie energii
napęd hybrydowy
testy drogowe
analiza zużycia energii
Opis:
The analysis of energy consumption in a hybrid drive system of a passenger car in real road conditions is an important factor determining its operational indicators. The article presents energy consumption analysis of a car equipped with an advanced Plug-in Hybrid Electric Drive (PHEV), driving in real road conditions on a test section of about 51 km covered in various environmental conditions and seasons. Particular attention was paid to the energy consumption resulting from the cooperation of two independent drive units, analyzed in terms of the total energy expenditure. The energy consumption obtained from fuel and energy collected from the car’s batteries for each run over the total distance of 12 500 km was summarized. The instantaneous values of energy consumption for the hybrid drive per kilometer of distance traveled in car’s real operating conditions range from 0.6 to 1.4 MJ/km, with lower values relating to the vehicle operation only with electric drive. The upper range applies to the internal combustion engine, which increases not only the energy expenditure in the TTW (Tank-to-Wheel) system, but also CO2 emissions to the environment. Based on the experimental data, the curves of total energy consumption per kilometer of the road section traveled were determined, showing a close correlation with the actual operating conditions. Obtained values were compared with homologation data from the WLTP test of the tested passenger car, where the average value of energy demand is 1.1 MJ/km and the CO2 emission is 23 g/km.
Źródło:
Combustion Engines; 2022, 61, 4; 15--22
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ wybranego przełożenia skrzyni biegów na emisję dwutlenku węgla przez pojazd podczas jego rozpędzania
The impact of the selected gear ratio on carbon dioxide emissions by vehicle during its acceleration
Autorzy:
Merkisz, J.
Andrzejewski, M.
Pielecha, J.
Powiązania:
https://bibliotekanauki.pl/articles/133091.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
badania drogowe
emisja CO2
rozpędzanie pojazdu
dwutlenek węgla
road tests
CO2 emissions
acceleration of vehicle
carbon dioxide
Opis:
W artykule zaprezentowano wyniki pomiarów toksyczności spalin samochodów osobowych w rzeczywistych warunkach ruchu w zależności od wybranego przełożenia skrzyni biegów (możliwego do zastosowania w danych warunkach jazdy), wykonane podczas rozpędzania tych samochodów do określonej prędkości. W oparciu o pozyskane dane pomiarowe dokonano oceny rozpędzania pojazdów uwzględniając minimalną emisję dwutlenku węgla. Rozpatrywanym osobno badaniom w warunkach drogowych poddano 2 samochody osobowe tej samej marki i tego samego modelu: jeden napędzany silnikiem o zapłonie iskrowym, a drugi silnikiem o zapłonie samoczynnym. Testy – rozpędzanie samochodów – wykonywano na pomiarowym odcinku jazdy, stosując różną liczbę biegów w celu osiągnięcia założonej maksymalnej prędkości jazdy. Na podstawie pomiarów i przyjętych kryteriów porównawczych oceniono wpływ rodzaju rozpędzania pojazdów na wielkość emisji dwutlenku węgla.
The article presents the results of measurements of exhaust emissions of cars in real traffic conditions depending on the selected gear (possible to use in the current driving conditions), made during the acceleration of the cars to a certain speed. Based on measured data the acceleration of the vehicles was analyzed, taking into account the minimum carbon dioxide emissions. In the considered separately studies two cars of the same brand and the same model were used: one driven by a spark-ignition engine and one by a compression-ignition engine. The road tests were performed at the measuring segment, using a different number of gears in order to achieve the assumed maximum speed. On the basis of test results and adopted criteria the influence of the style of vehicle acceleration on carbon dioxide emissions was evaluated.
Źródło:
Combustion Engines; 2013, 52, 3; 324-331
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of the selection of chosen technical parameters of the powertrain system for a diesel-electric rail-road tractor
Autorzy:
Daszkiewicz, Paweł
Andrzejewski, Maciej
Medwid, Marian
Urbański, Patryk
Cierniewski, Maksymilian
Woch, Aleksandra
Stefańska, Natalia
Powiązania:
https://bibliotekanauki.pl/articles/2097541.pdf
Data publikacji:
2021
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
rail-road tractor
electric drivetrain
zero emission
rail chassis
diesel-electric vehicle
ciągnik szynowo-drogowy
elektryczny układ napędowy
zeroemisyjność
podwozie szynowe
Opis:
The article presents the results of a simplified analysis of the feasibility of designing a rail chassis of a two-way tractor with an internal combustion or electric drive. Basic traction and operating parameters have been assumed for which the road-rail tractor could operate in an effective manner. On their basis, strength calculations were carried out and mechanical elements of the drive system meeting the required assumptions were selected. All the calculations presented in the text were fulfilled. The technical feasibility of building the mechanical part of the rail running gear of a rail-road tractor driven by an internal combustion engine or electric motors has been demonstrated.
Źródło:
Combustion Engines; 2021, 60, 3; 64--71
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-10 z 10

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies