Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "cząstki stałe" wg kryterium: Temat


Wyświetlanie 1-8 z 8
Tytuł:
Badanie emisji cząstek stałych z silników odrzutowych małych samolotów
The study of particulate emissions from small aircraft equipped in jet engine
Autorzy:
Pielecha, J.
Merkisz, J.
Markowski, J.
Jasiński, R.
Powiązania:
https://bibliotekanauki.pl/articles/133105.pdf
Data publikacji:
2015
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
silnik odrzutowy
cząstki stałe
związki szkodliwe spalin
jet engine
particulate matters
exhaust emission
Opis:
W artykule przedstawiono analizę rozkładu wymiarowego średnic cząstek stałych, emitowanych z turbinowego silnika lotniczego. Pomiary przeprowadzono w warunkach stacjonarnych symulując rzeczywiste warunki pracy silnika odrzutowego. Badania wykonano dla trzech początkowych faz pracy silnika: rozruchu, nagrzewania oraz pracy ustalonej. Otrzymane wyniki pozwoliły na wyznaczenie średnic cząstek stałych najczęściej występujących w danych warunkach, a jednocześnie skorelowano zmiany średnic cząstek stałych ze stężeniem gazowych związków szkodliwych spalin. W rezultacie otrzymano charakterystyki, na podstawie których stwierdzono, że rozkład wymiarowy średnic cząstek stałych w początkowej fazie pracy silnika charakteryzuje się dużą zmiennością. W pierwszym okresie pracy silnika dominują cząstki stałe o średnicach 20–30 nm oraz średnicach dużych (rzędu 100–140 nm), a w kolejnych okresach pracy ustabilizowanej dominują cząstki o średnicach z zakresu 30–40 nm.
The article presents an analysis of the size distribution of particulate matters emitted from jet engine. Measurements were carried out in stationary conditions simulating real operating conditions of the jet engine. The study was performed for the three initial phases of engine operation: start-up, warm-up and steady-state operation. The obtained results allowed to determine the particulate matters size distribution of the most common particulates emitted under given conditions also the changes of characteristic diameters of particulate matters have been correlated with exhaust emission. As a result, the particulate matters size distributions were obtained on the basis of which it was found that diameters of particulates in the initial phase of engine operation are characterized by high variability. Th first period of engine operation is dominated by particles with diameters of 20–30 nm and bigger diameters (around 100–140 nm), and in next periods of engine operation particles are characterized by diameters in size range of 30–40 nm.
Źródło:
Combustion Engines; 2015, 54, 3; 376-382
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparative tests of a passenger car with compression ignition engine on chassis dynamometer during NEDC and WLTC tests and during RDE road test
Autorzy:
Gis, Wojciech
Gis, Maciej
Wiśniowski, Piotr
Bednarski, Mateusz
Powiązania:
https://bibliotekanauki.pl/articles/134170.pdf
Data publikacji:
2019
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
emissions
pollutant emissions
particle matter
NEDC
WLTP
RDE
emisje
emisje zanieczyszczeń
emisja zanieczyszczeń
cząstki stałe
Opis:
Air pollution is a challenge for municipal authorities. Increased emission of PM10 and PM2.5 particles is particularly noticeable in Poland primarily the autumn and winter period. That is due to the start of the heating season. According to the above data, road transport accounted for approximately 5% of the creation of PM10 particles, ca. 7% of PM2.5 and approximately 32% for NOx. In Poland, suspended particles (PM10 and PM2.5) cause deaths of as many as 45,000 people a year. The issue of smog also affects other European cities. Therefore, it is necessary to undertake concrete efforts in order to reduce vehicle exhaust emissions as much as possible. It is therefore justifiable to reduce the emission of exhaust pollution, particularly NOx, PM, PN by conventional passenger cars powered by compression ignition engines. Emissions by these passenger cars have been reduced systematically. Comparative tests of the above emission of exhaust pollution were conducted on chassis dynamometer of such passenger car in NEDC cycle and in the new WLTC cycle in order to verify the level of emissions from this type of passenger car. Measurements of fuel consumption by that car were also taken. Emission of exhaust pollution and fuel consumption of the this car were also taken in the RDE road test.
Źródło:
Combustion Engines; 2019, 58, 3; 228-234
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Pomiar oraz identyfikacja cząstek stałych w spalinach silnika o zapłonie samoczynnym
The measurement and identification of the particulate matter in Diesel engine exhaust gases
Autorzy:
Mruk, A.
Cisek, J.
Powiązania:
https://bibliotekanauki.pl/articles/133051.pdf
Data publikacji:
2015
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
silnik o zapłonie samoczynnym
gazy spalinowe
cząstki stałe
identyfikacja PM
diesel engine
exhaust gases
particulate matter
PM identification
Opis:
W celu zidentyfikowania wśród cząstek stałych, cząstek innych niż sadza podano analizie filtry z badań silnika o zapłonie samoczynnym. Analizowane filtry pochodziły z badań 6-cylindrowego silnika sprawnego technicznie przy stałej prędkości obrotowej i obciążeniu. Wychwycone na filtrze cząstki podano obserwacji wykorzystując możliwości mikroskopu elektronowego i analizy spektralnej. Badania przeprowadzono na elektronowym mikroskopie skaningowym JSM-5800 firmy Jeol (Japonia), sprzężonym ze spektrometrem promieniowania rentgenowskiego Link ISIS 300 firmy Oxford Instruments Ltd. (Wielka Brytania). Stwierdzono, że na powierzchni filtra obok jednolitej w barwie i strukturze sadzy znajdują się inne, odróżniające się barwą i postacią. Cząstki te, po zlokalizowano udokumentowano i zbadano pod względem występujących w ich składzie pierwiastków. Określono również ich wymiary. Stwierdzono występowanie cząstek metalowych: stopy żelaza, cynku oraz krzemu. Wśród cząstek zaobserwowano również cząstki niejednorodne w postaci aglomeratów o zróżnicowanej budowie, złożonej z mikrocząstek różnego pochodzenia, zbudowanych z różnych materiałów.
To identify amid PM particulates the particles other than soot, the filters used in diesel engine testing have been analysed. Analysed filters had been applied in the study on a 6-cylinder, turbocharged diesel engine, technically proficient, working at constant torque and speed. The particles captured on the filter were put under observational study using the possibilities of electron microscope and spectroscopic analysis. The testing was done on a scanning electron microscope JSM-5800 of the firm Jeol (Japan), coupled with an X-ray spectrometer Link ISIS of the firm Oxford Instruments Ltd. (United Kingdom). It was found, that on the filter surface, besides the soot particles of uniform colour and structure, there were also other particles of different colour and form. These particles were localized and examined in terms of the chemical elements in their composition. Their dimensions also were determined. Metal particles were identified: ferrous alloy, zinc alloy and the silicon alloy. Amid the particulate matter, some heterogeneous particles were identified. They had the form of agglomerates of different structure, compound of elementary particles of different origins and materials.
Źródło:
Combustion Engines; 2015, 54, 3; 732-743
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
PM emission in the exhaust gas of SI engines fed with petrol or LPG
Emisja cząstek stałych w spalinach silnika ZI zasilanego benzyną lub mieszaniną propanu i butanu
Autorzy:
Dutczak, J.
Powiązania:
https://bibliotekanauki.pl/articles/133192.pdf
Data publikacji:
2014
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
SI engine
exhaust gas emissions
particulate matter
nanoparticles
petrol
LPG
silnik ZI
emisja spalin
cząstki stałe
nanocząstki
benzyna
Opis:
The paper presents measurements of PM emission in the exhaust gas of a gasoline fueled SI engine alternatively fueled with LPG. The research was performed on a 170.A1 engine using the Dekati ELPI+ PM analyzer and Micro Diluter 6100 (a micro-dilution tunnel). The author also measured the concentration of exhaust gaseous components with the use of Horiba MEXA 1500GH analyzer. The author compared the PM concentration and size distribution in the exhaust gas for both fuels.
W artykule przedstawiono pomiary emisji cząstek stałych (PM) w spalinach silnika ZI zasilanego benzyną albo skroploną mieszaniną propanu i butanu. Badania przeprowadzono na silniku 170.A1 z użyciem analizatora cząstek stałych Dekati ELPI+ wyposażonego w minitunel rozcieńczający Micro Diluter 6100. Równocześnie dokonano pomiaru stężenia gazowych składników spalin za pomocą analizatora Horiba MEXA 1500GH. Zmierzono stężenie oraz rozkład wielkości i liczbę cząstek stałych w spalinach, a następnie porównano uzyskane wyniki dla obu paliw.
Źródło:
Combustion Engines; 2014, 53, 3; 36-44
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Engine-generated solid particles - a case study
Autorzy:
Szramowiat, K.
Woodburn, J.
Pacura, W.
Berent, K.
Bielaczyc, P.
Gołaś, J.
Powiązania:
https://bibliotekanauki.pl/articles/134094.pdf
Data publikacji:
2018
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
engine emissions
particulate matter
nanoparticles
scanning electron microscopy
SEM
morphology
emisja spalin
cząstki stałe
nanocząstki
elektronowy mikroskop skaningowy
morfologia
Opis:
Current ecological trends and resulting legislation like European emissions standards Euro 6d or Best Available Techniques are setting new challenges in the field of environmental protection. Since the problem of emissions of particulate matter from diesel engines was solved by the application of diesel particulate filters (DPFs or FAPs) and due to the global dominance of gasoline fuelled passenger cars, particular concern has been focused on improvement of emissions performance of gasoline vehicles, including hybrids, as well as heavy-duty and non-road vehicles. This paper presents the results of preliminary studies on the chemical and physical properties of gasoline engine-generated particles, including nanoparticles. SEM images were presented which allowed identification of the character of particulate matter and estimates of the dimensions of particles. Moreover, the particles were found to be composed of different elements, including Cu, Si, Na, Ca, Zn and P, pointing to the origination of these particles from the pistons and lubricant additives.
Źródło:
Combustion Engines; 2018, 57, 3; 33-39
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Emissions of the combustion engine as a source of cold for its extreme intercooling
Autorzy:
Hlavňa, V.
Krakovsky, J.
Powiązania:
https://bibliotekanauki.pl/articles/134059.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
non-conventional energetic system
cooling combustion engine
extreme intercooling
PM formation
particulate matters
niekonwencjonalny system energetyczny
chłodzenie międzystopniowe
cząstki stałe
Opis:
This paper contains results of mathematical modeling connected with non-conventional energetic system using the cooling combustion engine (the engine cooling circle is the ejector of absorption cooling). We especially have focused on the influence of a more intensive cooling on the engine ecological parameters. The paper is a continuation of previous publications and focuses on the results of the designed mathematical model of particulate matter formation and its experimental verification under extreme intercooling. Our previous achievements were already presented on scientific conferences and in professional journals.
Źródło:
Combustion Engines; 2013, 52, 2; 20-27
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study of dual-fuel (diesel + natural gas) particle matter and CO2 emissions of a heavy-duty diesel engine during transient operation
Autorzy:
Barroso, P.
Ribas, X.
Pita, M.
Dominguez, J.
De Seia, E.,
García, J.-M.
Powiązania:
https://bibliotekanauki.pl/articles/134220.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
dual fuel
natural gas
diesel engine
heavy-duty
transient
particle matter
CO2
silnik dwupaliwowy
gaz ziemny
silnik spalinowy
cząstki stałe
dwutlenek węgla
Opis:
The aim of this study is to describe the impact on particle matter and CO2 emissions of converting an existing heavy-duty diesel engine for on-highway truck applications to a dual-fuel engine (diesel + natural gas), especially in transient operation. A dual-fuel engine with homogeneous gas charge injection in the intake line before turbocharger was considered. The results showed the feasibility of this kind of technology for transient operation reaching a significant reduction of particle matter plus a decrement in CO2 emissions at the expense of a small decrement of brake fuel conversion efficiency and an increment of unburned hydrocarbons in the exhaust gases.
Źródło:
Combustion Engines; 2013, 52, 2; 3-11
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impact of EGR control at in-cylinder pressure and ecological properties of CI off-road vehicle engine
Autorzy:
Bieniek, A.
Mamala, J.
Graba, M.
Hennek, K.
Powiązania:
https://bibliotekanauki.pl/articles/133493.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
exhaust gas recirculation
in-cylinder pressure
mass fraction burning
differential pressure
nitrogen oxides
NOx
particulate matter
PM
recyrkulacja spalin
ciśnienie w cylindrze
spalanie frakcji masowej
różnica ciśnień
tlenki azotu
cząstki stałe
Opis:
An attempt has been made to clarify the effect of wide-ranging control of the exhaust gas recirculation system on the cylinder pressure and ecological engine performance. This publication contains the results of tests performed on the CI (compression ignition) engine of the off-road vehicle mounted on the test bench. The study was based on advanced EGR control with a proportional valve and a very efficient exhaust gases cooling system. Analysis of the test results is based on the cylinder pressure and the concentration of NOx and PM components at exhaust gases. The study included the influence of the exhaust gas recirculation system control on parameters such as differential pressure, MBF, and relative NOx and PM emissions. As demonstrated by the analysis conducted, the EGR valve control method and the exhaust gas cooling intensity significantly affect the cylinder pressure and its ecological performance.
Źródło:
Combustion Engines; 2017, 56, 3; 88-95
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-8 z 8

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies