Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "K. W." wg kryterium: Autor


Tytuł:
Novel Extraction Process Of Rare Earth Elements From NdFeB Powders Via Alkaline Treatment
Nowy sposób ekstrakcji pierwiastków ziem rzadkich z proszków NdFeB w roztworach alkalicznych
Autorzy:
Chung, K. W.
Kim, C.-J.
Yoon, H.-S.
Powiązania:
https://bibliotekanauki.pl/articles/355324.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
recycling
NdFeB magnet
alkaline treatment
leaching
selective leaching efficiency
recykling
magnes neodymowy
obróbka alkaliczna
ługowanie
wydajność
Opis:
The alkaline treatment of NdFeB powders in NaOH solution at various equivalent amounts of NaOH at 100°C was performed. The resultant powders were then leached in 0.5M H2SO4 solution at 25°C for 2 minutes. At 5 equivalents of NaOH, neodymium in NdFeB powders was partially transformed to neodymium hydroxide. The transformation of neodymium to neodymium hydroxide actually occurred at 10 equivalents of NaOH and was facilitated by increasing the equivalent of NaOH from 10 to 30. In addition, iron was partially transformed to magnetite during the alkaline treatment, which was also promoted at a higher equivalent of NaOH. The leaching yield of neodymium from alkaline-treated powders was increased with an increasing equivalent of NaOH up to 10; however, it slightly decreased with the equivalent NaOH of over 10. The leaching yield of iron was inversely proportional to that of rare earth elements. NdFeB powders treated at 10 equivalents of NaOH showed a maximum leaching yield of neodymium and dysprosium of 91.6% and 94.6%, respectively, and the lowest leaching yield of iron of 24.2%, resulting in the highest selective leaching efficiency of 69.4%.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1301-1305
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Preparation Of Fine Grained SiC At Reduced Temperature By Two-Step Sintering
Wytwarzanie drobnoziarnistego SiC w obniżonej temperaturze przez dwuetapowe spiekanie
Autorzy:
Kim, K.-W.
Oh, K.-S.
Lee, H.
Kim, B. S.
Chung, T.-J.
Powiązania:
https://bibliotekanauki.pl/articles/353772.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
SiC
liquid phase
two step sintering
coarsening
hardness
faza ciekła
spiekanie dwuetapowe
odporność
twardość
Opis:
Two-step sintering route was applied for the densification SiC by promoting the role of liquid phase. The specimen contained 8 vol% of liquid phase composed of Al2O3 and Y2O3. The heating schedule consisted with initial rapid heating to 2000°C and immediate quenching to 1700 or 1750°C. By heating at elevated temperature, even distribution of the liquid phase was intended. The heat treatment at reduced temperature was to suppress the evaporative loss of the liquid and to secure the time for densification. The two-step sintering effectively suppressed loss of mass and coarsening. The resultant SiC was thus dense and was composed of fine grains exhibiting hardness of 2321 kgf/mm2.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1539-1542
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis And Electrochemical Characteristics Of Mechanically Alloyed Anode Materials SnS2 For Li/SnS2 Cells
Synteza mechaniczna i charakterystyka elektrochemiczna materiałów anodowych SnS2 dla ogniw Li/SnS2
Autorzy:
Hong, J. H.
Liu, X. J.
Park, D. K.
Kim, K. W.
Ahn, H. J.
Ahn, I. S.
Powiązania:
https://bibliotekanauki.pl/articles/356903.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
MA
Li/SnS2 cell
PCA
wet milling process and electrochemical characteristics
ogniwa Li/SnS2
charakterystyka elektromechaniczna
Opis:
With the increasing demand for efficient and economic energy storage, tin disulfide (SnS2), as one of the most attractive anode candidates for the next generation high-energy rechargeable Li-ion battery, have been paid more and more attention because of its high theoretical energy density and cost effectiveness. In this study, a new, simple and effective process, mechanical alloying (MA), has been developed for preparing fine anode material tin disulfides, in which ammonium chloride (AC), referred to as process control agents (PCAs), were used to prevent excessive cold-welding and accelerate the synthesis rates to some extent. Meanwhile, in order to decrease the mean size of SnS2 powder particles and improve the contact areas between the active materials, wet milling process was also conducted with normal hexane (NH) as a solvent PCA. The prepared powders were both characterized by X-ray diffraction, Field emission-scanning electron microscopeand particle size analyzer. Finally, electrochemical measurements for Li/SnS2 cells were takenat room temperature, using a two-electrode cell assembled in an argon-filled glove box and the electrolyte of 1M LiPF6 in a mixture of ethylene carbonate(EC)/dimethylcarbonate (DMC)/ethylene methyl carbonate (EMC) (volume ratio of 1:1:1).
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1191-1194
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effects of Friction on Stamping Process of Sheet Metals Used in Aviation
Wpływ tarcia na proces tłoczenia blach stosowanych w lotnictwie
Autorzy:
Dyja, K.
Więckowski, W.
Powiązania:
https://bibliotekanauki.pl/articles/356581.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
sheet
sheet-metal forming
friction
technological lubricant
arkusz
odkształtcenia blachy
tarcie
Opis:
An important factor in the possibility of obtaining correct drawn parts with the desired functional properties is the friction between the stamped sheet and the tool. The article discusses the impact of technological lubricants developed according to our own formulas, based on vegetable oils, on the stamping process taking into account the strain distributions in the drawn parts. Biodegradable lubricants based on rapeseed oil with an addition of stearic acid or boric acid were used. The results of the friction coefficient in a strip drawing test and the numerical analysis results of the stamping process of a spherical cap from sheet metal: aluminium 2024, commercially pure titanium Grade 2, steel 5604 in dry friction and lubrication conditions, are presented. Strain distributions and changes in the drawn part wall thickness were analysed.
Istotnym czynnikiem decydującym o możliwości uzyskania poprawnych wytłoczek o żądanych właściwościach użytkowych jest tarcie występujące pomiędzy tłoczoną blachą a narzędziem. Tarcie występujące w procesach obróbki plastycznej ma bezpośredni wpływ na: rozkład naprężeń i odkształceń w objętości kształtowanego materiału, graniczną - możliwą do uzyskania wysokość wytłoczki oraz wielkość siły tłoczenia. Podstawowym sposobem ograniczania wielkości oporów tarcia w obróbce plastycznej jest odpowiednie smarowanie. Dodatkowo smary technologiczne zapobiegają bezpośredniemu kontaktowi obrabianego materiału z narzędziem, a tym samym zacieraniu i nalepianiu kształtowanego materiału na powierzchniach roboczych narzędzia, przez co znacząco wpływają na jakość otrzymywanych elementów oraz trwałość narzędzi. Smary dobiera się do konkretnych procesów oraz rodzaju kształtowanych materiałów, wielkości nacisków, stanu współpracujących powierzchni oraz prędkości poślizgu i temperatury pracy. Wpływ poszczególnych czynników na opory tarcia jest złożony i wymaga prowadzenia szeregu badań doświadczalnych z zakresu przydatności smaru technologicznego do poszczególnych procesów formowania. W artykule omówiono wpływ smarów technologicznych opracowanych według własnych receptur na przebieg procesów tłoczenia z uwzględnieniem rozkładów odkształceń w wytłoczkach. Zastosowano biodegradowalne smary oparte na olejach roślinnych tj. oleju rzepakowym z dodatkiem kwasu stearynowego lub kwasu borowego. Przedstawiono wyniki badań współczynnika tarcia w próbie przeciągania pasa blachy oraz wyniki analiz numerycznych procesu tłoczenia czaszy kulistej z blach: aluminiowej 2024, tytanowej Grade2 i stalowej 5604 w warunkach tarcia technicznie suchego oraz w warunkach smarowania. Analizowano rozkłady odkształceń oraz zmiany grubości ścianek wytłoczek.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 3A; 1895-1900
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of the Use of Technological Lubricants Based on Vegetable Oils on the Process of Titanium Sheet Metal Forming
Autorzy:
Więckowski, W.
Dyja, K.
Powiązania:
https://bibliotekanauki.pl/articles/353140.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
sheet metal forming
tribological system
technical lubricant
numerical simulation (FEM)
Opis:
The paper evaluates the drawability of titanium sheet metal Grade 2, with the focus on friction conditions that are present in the sheet metal forming process. The study aims to present the results of the examinations of the friction coefficient during a strip drawing test. The focus of the experiment was on lubricants based on vegetable oils i.e. rapeseed oil, sunflower oil and olive oil. Boric acid was used to improve the lubricating properties of vegetable oils. The results of numerical simulations of the process of forming a cover with stiffening components made of grade 2 titanium sheet metal was also presented. The numerical simulation was carried out using the FEM method with PAMStamp 2G software. The effect of conditions of friction between the sheet metal and tool parts and pressure force of the blank holder on the forming process were investigated. Numerical calculations were performed with consideration for the phenomenon of material strain hardening and anisotropy of plastic properties of the sheet metal formed. The analysis of the deformations and reduction in wall thickness of the drawn parts can be used for determination of the effect of changes in selected parameters on the process of drawn part forming. The quality of drawn parts was assessed based on the shape inaccuracy determined during simulation of forming. The inaccuracy depended on the conditions of the process and strength properties of the titanium sheet metal.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2A; 489-494
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Heat exchange in the system mould - riser - ambient. Part II: Surface heat emission from open riser to ambient
Wymiana ciepła w układzie forma - nadlew - otoczenie. Część II: Współczynnik emisji ciepła z otwartego nadlewu do otoczenia
Autorzy:
Krajewski, P. K.
Gradowski, A.
Krajewski, W. K.
Powiązania:
https://bibliotekanauki.pl/articles/352192.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
castings
risers
surface heat emission
heat balance
solidification modelling
odlewy
nadlew
emisja ciepła
bilans cieplny
modelowanie krzepnięcia
Opis:
The subject of the paper is heat exchange in the system casting - riser - ambient. The examinations were focused on evaluating temperature dependence of the coefficient of heat exchange from open (not shielded) top surface of riser to ambient. The examinations were carried out on the open surface of cast steel riser, of temperatures 1000-1500°C. On the basis of the performed examinations it was stated that heat emission coefficient changes its mean values by about 50% during feeding process of the mild steel casting, i.e. from about 0.28 in liquid state to about 0.42 at temperatures close to solidus. This wide range of surface heat emissivity changes should be taken into account when boundary conditions are formulated in elaborated models of solidification and in designing risering systems.
Przedmiotem artykułu jest wymiana ciepła w systemie odlew - nadlew - otoczenie. Celem badań było wyznaczenie temperaturowej zależności współczynnika wymiany ciepła z odkrytej, nieizolowanej powierzchni nadlewu do otoczenia. Badania wykonano dla odlewu staliwnego z odkrytym nadlewem, dla zakresu temperatury powierzchni nadlewu 1000-1500°C. Na podstawie wykonanych badań stwierdzono, iż współczynnik emisji ciepła z nieizolowanej powierzchni nadlewu do otoczenia zmienia swą wartość w badanym zakresie temperatury o około 50%, tj. od około 0.26 - 0.30 dla metalu w stanie ciekłym do około 0.42 - 0.46 dla metalu w stanie stałym, w pobliżu temperatury solidus. Powyższy szeroki zakres zmian emisyjności powinien być uwzględniany w budowanym modelach symulacji procesu krzepnięcia i projektowania systemów zasilania krzepnących odlewów.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 4; 1149-1153
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Root Canal System Analysis with a Group of First Permanent Molars of Upper and Lower Jaw
Analiza systemu kanałowego w pierwszych zębach trzonowych szczęki i żuchwy
Autorzy:
Mroczek, K.
Szlązak, K.
Jodkowska, E.
Święszkowski, W.
Kurzydłowski, K.J.
Powiązania:
https://bibliotekanauki.pl/articles/355703.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
endodontics
root canal system configuration
microtomography
endodoncja
konfiguracja kanałów korzeniowych
mikrotomografia
Opis:
A progressive bacteria invasion on tooth tissues leads to pulp inflammation, microabscesses of the pulp, destruction and in consequence inflammation of periapical tissues. Therefore the aim of endodontic treatment is three dimensional debridement of a root canal from the vent in pulp chamber to the physiological narrowing. Therefore the aim of the study is analysis of root canal configuration, number of canals, presence of lateral canals and canal delta with the group of first permanent molars. At the same time the accuracy of the radiological examination (x-ray images) is estimated due to comprehension of X-ray images performed before teeth preparation with root canal system and after observation of transversal cuts by means of light microscopy and microtomography. This establishment is presented through the differences in conventional radiological image and clinical assessment.
Postępująca inwazja bakteryjna w tkankach zęba prowadzi do zapalenia miazgi, powstawania w niej mikroropnii, zniszczenia a w konsekwencji do zapalenia ozębnej. Z tego względu celem leczenia endodontycznego stało się trójwymiarowe oczyszczenie kanału korzeniowego od jego ujścia do przewężenia fizjologicznego. Dlatego celem pracy jest analiza konfiguracji, ilości kanałów korzeniowych, istnienia kanałów bocznych oraz delty korzeniowej w grupie pierwszych zębów trzonowych stałych w uzębieniu ludzkim. Jednocześnie ocenie poddawana jest dodatkowo swoistość badania radiologicznego (zdjęcia zębowe), poprzez porównanie zdjęć rentgenowskich wykonanych przed preparacją zębów z obrazem systemu kanałowego uzyskanego na podstawie mikrotomografii oraz po wykonaniu szlifów poprzecznych i ich obserwacji na mikroskopie świetlnym. Celem tej oceny jest zaprezentowanie rozbieżności pomiędzy oceną radiologiczną systemu kanałowego a kliniczną.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 2; 629-632
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of the Possibility of Calculating the Charges on the Example of Brasses
Autorzy:
Biernat, S.
Bydałek, A. W.
Wołczyński, W.
Najman, K.
Powiązania:
https://bibliotekanauki.pl/articles/356905.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
quality management castings
alloy
brass
calculating
batch
Opis:
This paper describes the subject of brasses and the method of their production from the secondary raw materials. It focuses on two very important aspects extremely important for today’s world. The first of them is the theme of rational management of materials, particularly metallic scrap. The second issue is the growing importance of products made of brass, which in recent times get also special recognition in medicine. This article presents a proposal for a methodology for calculating the metal charge for brasses of two or more components. It turns out that by using suitable mathematical calculations one can accurately determine the amount of metal charge to obtain a product having the desired chemical composition and desired mechanical properties. Mathematical calculations are also presented in the graphical form for the visualization of dependency and a better explanation of the accepted approach.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 4; 2165-2170
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Deposition of Gold Nanoparticles Onto Activated Carbon
Osadzanie nanocząstek złota na węglu aktywnym
Autorzy:
Jaworski, W.
Streszewski, B.
Szaciłowski, K.
Pacławski, K.
Powiązania:
https://bibliotekanauki.pl/articles/351364.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
gold nanoparticles
activated carbon
functionalization
amines
nanocząstki złota
węgiel aktywny
funkcjonalizacja
aminy
Opis:
This work reports the results of spectrophotometric, dynamic light scattering (DLS) and microscopic (SEM) studies of the gold nanoparticles (AuNPs) deposition on activated carbon (AC) surface modified with primary (ethanolamine) and secondary (diethylenetriamine and triethylenetetramine) amines. It was found that this method is efficient for deposition of AuNPs from aqueous solution. However, nanoparticles change their morphology depending on the kind of amine used in experiments. On the AC surface modified with ethanolamine, the uniform spherical AuNPs were formed. In case of diethylenetriamine and triethylenetetramine application, the agglomerates of AuNPs are present. The diameter of individual AuNPs did not exceed 15 nm and was bigger as compared with the diameter of particles present in precursor solution (ca. 10 nm).
W pracy przedstawiono wyniki badań spektrofotometrycznych, metodą dynamicznego rozpraszania światła (DLS) oraz mikroskopowe (SEM) dotyczące osadzania nanocząstek złota na węglu aktywnym, modyfikowanym aminami: pierwszorzędową (etanoloamina) i drugorzędowymi (dietylenotriamina i trietylenotetraamina). Wykazano, że ten sposób modyfikacji umożliwia osadzanie nanocząstek złota z roztworu wodnego na powierzchni węgla. W zależności od rodzaju używanej aminy ulega jednak zmianie morfologia osadów nanocząstek. Na powierzchni węgla aktywnego, modyfikowanego etanoloaminą, tworzą się jednorodne cząstki złota o kształcie sferycznym. W przypadku zastosowania dietylenotriaminy oraz trietylenotetraaminy obserwowano powstawanie agregatów nanocząstek. Średnica pojedynczych nanocząstek nie przekraczała 15 nm i była większa od średnicy nanocząstek obecnych w roztworze prekursora (ok. 10 nm).
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 3; 899-903
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Protecting Melted Zinc-Aluminium based Foundry Alloys Against Hydrogen Pick-Up
Ochrona przetapianych odlewniczych stopów cynk-aluminium przed pochłanianiem wodoru
Autorzy:
Krajewski, W. K.
Piwowarski, G.
Krajewski, P. K.
Powiązania:
https://bibliotekanauki.pl/articles/355834.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
zinc
Zn-Al alloy
hydrogen pick-up
fluxing
refining
strength properties
yield
cynk
stop Zn-Al
pochłanianie wodoru
topnik
rafinacja
właściwości wytrzymałościowe
wydajność
Opis:
The paper is devoted to examinations of the refining efficiency of fluxes and refiners applied during melting of zinc and zinc-aluminium alloys. The content of gases, mainly hydrogen, in the alloys not protected during the charge melting and in the ones protected with the fluxes and/or refined is discussed. The performed examinations show that using the protecting fluxes and melt-refining before pouring leads to significant improvement of ductility in Zn and binary Zn-Al alloys as well as significant increase of the material clearness confirmed by increased density. Furthermore, the metallurgical yields are also increased.
Praca poświęcona jest badaniom rafinacyjnej skuteczności żużli ochronnych i rafinatorów stosowanych w technologii przetapiania cynku oraz stopów cynk-aluminium. Wykonane badania wykazały, iż Zn i stopy podwójne Zn-Al przetapiane pod żużlami ochronnymi oraz przerafinowane przed odlaniem do formy wykazują zwiększoną plastyczność i zwiększoną czystość, potwierdzoną podwyższoną gęstością masy. Dodatkowo, wzrastają uzyski metalurgiczne.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 2; 753-755
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and Properties of Surface Layer of Carburized 38CrAlMo6-10 Steel Subjected to Nanostructurization by a Heat Treatment Process
Struktura i właściwości warstwy nawęglanej na stali 38CrAlMo6-10 po procesie nanostrukturyzacji w warunkach obróbki cieplnej
Autorzy:
Wasiluk, K.
Skołek, E.
Świątnicki, W.
Powiązania:
https://bibliotekanauki.pl/articles/352483.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
carburization
austempering
low-temperature bainite
nanobainite
nawęglanie
hartowanie
bainit niskotemperaturowy
nanobainit
Opis:
The aim of the study was to produce and characterize a nanobainitic microstructure in surface layers of carburized 38CrAlMo6-10 structural steel. Steel contained 1.% Al and 0.3% Si - elements hindering the cementite precipitation, which was considered to be adequate for obtaining a carbide free bainite. Steel samples were subjected to two different vacuum carburizing processes in order to obtain two different contents of carbon in surface layer. To produce a nanobainitic microstructure a heat treatment consisting of austempering at temperature slightly higher than the martensite start temperature (Ms) of the layer was applied after each carburization process. It was found, that the obtained microstructure of carburized layer depends strongly on carbon content. In steel with surface layer containing lower carbon content a nanobainitic microstructure with carbon-enriched residual austenite was formed. In case of surface layer containing higher carbon content the ultra-fine grained lower bainite was obtained.
Celem pracy było wytworzenie w nawęglonej warstwie wierzchniej stali 38CrAlMo6-10 mikrostruktury nanobainitu. Stal ta zawiera dodatek 1,31% Al+Si - pierwiastków hamujących wydzielanie węglików, który został uznany za wystarczający by umożliwić powstanie nanobainitu. Próbki poddano dwóm procesom nawęglania do dwóch różnych zawartości węgla w warstwie wierzchniej. Zastosowana obróbka cieplna nanobainityzacji obejmowała hartowanie izotermiczne w temperaturach nieco wyższych niż Ms warstwy. Uzyskane wyniki pozwalają stwierdzić, że mikrostruktura warstwy wierzchniej po bainityzacji zależy silnie od zawartości węgla. W przypadku jednej warstwy uzyskano nanometrycznej wielkości listwy bainitu z filmem wzbogaconego w węgiel austenitu resztkowego, w drugiej mikrostrukturę ultra drobnoziarnistego bainitu dolnego.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 4; 1685-1690
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Trends in the development of high-aluminium zinc alloys of stable structure and properties
Trendy rozwojowe wysokoaluminiowych stopów cynku o stabilnej strukturze i właściwościach
Autorzy:
Krajewski, W. K.
Greer, A. L.
Krajewski, P. K.
Powiązania:
https://bibliotekanauki.pl/articles/351886.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high-aluminium zinc alloys
grain refinement
in situ composite
dimensional stability
wear
stopy aluminium
wysokoaluminiowe stopy cynku
kompozyt in situ
stabilność wymiarowa
zużycie
Opis:
The coposition and structural modification of high-aluminium zinc alloys influence their strenght, tribological properties and structural stability. In a series of studies, Zn - (25-26) wt.% Al - (1-2.5) wt.% Cu alloys have been doped with different levels of added Ti. The alloys’ structure and mechanical properties have been studied using: SEM (scanning electron microscopy), LM (light microscopy), Dilatometry, Pin-on-Disc wear and Strength measurements. Grain refinement leads to significant improvement of ductility in the binary Zn-25Al alloy. In the ternary alloys Zn-26Al-Cu, replacing a part of Cu with Ti allows dimensional changes to be reduced while preserving good tribological properties.
Praca poświęcona jest badaniom wpływu modyfikacji składu i struktury wysokoaluminiowych odlewanych stopów cynku na ich właściwości wytrzymałościowe, tribologiczne oraz stabilność struktury i wymiarów. W badaniach stopy Zn - (25-26) mas% Al - (1-2.5) mas.% Cu domieszkowano zmiennym dodatkiem Ti. W badaniach stosowano techniki pomiarowe SEM (scanning electron microscopy), LM (light microscopy), badania dylatometryczne, badania ścieralności Pin-on-Disc oraz badania właściwości wytrzymałościowych. Stwierdzono, iż rozdrobnienie struktury pozwala uzyskać znaczący wzrost plastyczności stopów podwójnych typu Zn-25Al, podczas gdy zastąpienie tytanem części miedzi w stopach potrójnych Zn-26Al-Cu pozwala ograniczyć zmiany wymiarowe przy zachowaniu wysokich właściwości tribologicznych.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 3; 845-847
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Heat exchange in the system mould–riser–ambient. Part I: Heat exchange coefficient from mould external surface
Wymiana ciepła w układzie forma-nadlew-otoczenie. Część I: Współczynnik wymiany ciepła z zewnętrznej powierzchni formy
Autorzy:
Krajewski, P. K.
Zovko-Brodarac, Z
Krajewski, W. K.
Powiązania:
https://bibliotekanauki.pl/articles/354158.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
casting
casting mould
solidification modelling
heat exchange coefficient
odlewanie
forma odlewnicza
modelowanie krzepnięcia
współczynnik wymiany ciepła
Opis:
The subject of the paper is heat exchange in the system casting - riser - ambient. The examinations were focused on evaluating temperature dependence of the coefficient of heat exchange from mould external surface (or from riser thermally insulated surface) to ambient. The examinations were carried out for the surface temperatures of 200-800°. On the basis of the performed examinations it was stated that the relationship αext:eff vs. surface temperature can be described by a polynomial of 3rd degree with accuracy of 90-95% and that the αext:eff coefficient significantly depends on the examined material mass density.
Praca dotyczy określenia temperaturowej zależności współczynników, opisujących intensywność wymiany ciepła w układzie odlew - nadlew - forma odlewnicza - otoczenie. Na podstawie pomiarów temperatury i bilansów cieplnych określono wartości sumarycznego współczynnika wymiany ciepła do otoczenia z powierzchni nagrzanej warstwy ochronnej (izolacyjnej) górnej powierzchni nadlewu, w zakresie temperatury 200-800°. Uzyskano zależności o stosunkowo dobrym dopasowaniu, na poziomie R2 (0.9-0.95). Porównawcza analiza wyników dla dwóch zbadanych materiałów, różniących się gęstością masy i pojemnością cieplną, wykazała, iż nie ma prostej zależności pomiędzy nimi, to jest wartość sumarycznego współczynnika wymiany ciepła nie zmienia się wprost proporcjonalnie do iloczynu gęstości masy i pojemności cieplnej. Uzyskane wyniki mogą być wykorzystane do określenia warunków początkowo-brzegowych w konstruowanych modelach numerycznych wymiany ciepła w układach odlew - nadlew - forma odlewnicza - otoczenie.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 3; 833-835
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Mechanical properties of titanium processed by hydrostatic extrusion
Właściwosci mechaniczne tytanu wyciskanego hydrostatycznie
Autorzy:
Topolski, K.
Garbacz, H.
Wieciński, P.
Pachla, W.
Kurzydłowski, K. J.
Powiązania:
https://bibliotekanauki.pl/articles/356423.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
właściwości mechaniczne tytanu
tytan
wyciskanie hydrostatyczne
severe plastic deformation (SPD)
nanocrystalline titanium
hydrostatic extrusion (HE)
mechanical properties
nanocrystalline structure
Opis:
The mechanical properties of titanium Grade 2 subjected to the hydrostatic extrusion technique (HE) were investigated. The hydrostatic extrusion technique is a method which refines the titanium grains to a nano-metric size. Compared with coarse grained titanium (CG-Ti), nanocrystalline titanium (NC-Ti) is characterized by a much higher yield stress, tensile strength and microhardness. The yield stress of NC-Ti determined in tensile tests is higher than that measured in compression test. The Young modulus of NC-Ti is slightly lower than that of CG-Ti.
Przedmiot badań stanowiły właściwości mechaniczne tytanu Grade 2 poddanego wyciskaniu hydrostatycznemu. Technika wyciskania hydrostatycznego jest metodą, która umożliwia rozdrobnienie ziarna tytanu do wielkości nano-metrycznej. W porównaniu z tytanem gruboziarnistym (CG-Ti), tytan nanokrystaliczny (NC-Ti) charakteryzuje się o wiele wyższą granicą plastyczności, wytrzymałości na rozciąganie oraz mikrotwardością. Granica plastyczności NC-Ti wyznaczona podczas testów rozciągania jest wyższa niż granica plastyczności wyznaczona w testach ściskania. Natomiast moduł Young'a nanokrystalicznego tytanu jest nieznacznie mniejszy niż moduł tytanu gruboziarnistego.
Źródło:
Archives of Metallurgy and Materials; 2012, 57, 3; 863-867
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dynamic Mode of Copper Recovery from the Post-Processing Slags
Autorzy:
Wołczyński, W.
Bydałek, A. W.
Migas, P.
Tarasek, A.
Najman, K.
Powiązania:
https://bibliotekanauki.pl/articles/352769.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
post-processing slag
complex reagent
copper recovery
arc furnace
rotating tilted electrode
Opis:
The post-processing slags containing about 0.8 wt.% of copper were subjected to the treatment of a complex reagent. The chemical composition of the complex reagent has been elaborated and patented in frame of the Grant No. PBS3/A5/45/2015. The slags had an industrial origin and were delivered by the Smelter and Refinery Plant, Głogów, as a product of the direct-to-blister technology performed in the flash furnace assisted by the arc furnace. An agglomeration of copper droplets suspended in the liquid slag, their coagulation, and deposition on the bottom of furnace were observed after the treatment this post-processing slag by the mentioned reagent. The treatment of the post-processing slags by the complex reagent was performed in the arc furnace equipped with some additional electrodes situated at the furnace bottom (additional, in comparison with the arc furnace usually applied in the Smelter and Refinery Plant, Głogów). The behaviour of the copper droplets in the liquid slag within the competition between buoyancy force and gravity was studied from the viewpoint of the required deposition of coagulated copper droplets. The applied complex reagent improves sufficiently the surface free energy of the copper droplets. In the result, the mechanical equilibrium between coagulated copper droplets and surrounding liquid slag is properly modified. Eventually, sufficiently large copper droplets are subjected to a settlement on the furnace bottom according to the requirements. The agglomeration and coagulation of the copper droplets were significantly improved by an optimized tilting of the upper electrodes and even by their rotation. Moreover, the settlement was substantially facilitated and improved by the employment of both upper and lower system of electrodes with the simultaneous substitution of the variable current by the direct current.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 4; 1923-1930
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies