Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "(i.d.)." wg kryterium: Autor


Tytuł:
Mechanical Spectroscopy of Ordered Binary Au-Cu
Spektroskopia mechaniczna uporządkowanego stopu Au-Cu
Autorzy:
Tkalcec, I.
Mari, D.
Schaller, R.
Powiązania:
https://bibliotekanauki.pl/articles/352868.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
internal friction
gold alloys
order-disorder phase transition
Zener relaxation
tarcie wewnętrzne
stopy złota
kolejność zaburzeń przemiany fazowej
relaksacje Zenera
Opis:
We have studied a binary Au-Cu single crystal by mechanical spectroscopy. Upon very slow cooling from high temperatures, additional relaxation peaks arise at lower frequencies in isothermal spectra after the disappearing of the Zener peak below 665 K due to ordering. A high transient peak is visible at 660 K and it progressively disappears on cooling until 625 K. Another high peak is clearly visible upon following heating until 660 K. Above that temperature it decreases in parallel with the increase of the Zener peak. If the ordered structure is obtained by slowly heating the sample that has been quenched from the disordered state, no low-frequency peak is visible in the isothermal spectra, only a much lower background, which further decreases in parallel with the reappearance of the Zener peak. The low frequency relaxations are possibly due to the movement of antiphase boundaries and twin interfaces in the ordered structures.
Przy użyciu spektroskopii mechanicznej badano monokryształ Au-Cu. Podczas bardzo powolnego chłodzenia z wysokich temperatur, w skutek uporządkowania pojawiają się dodatkowe piki relaksacyjne przy niższych częstotliwościach w widmach izotermicznych po zniknięciu piku Zenera poniżej 665 K. Wysoki pik przejścia widoczny jest w 660 K i stopniowo znika podczas chłodzenia aż do 625 K. Kolejny wysoki pik jest wyraźnie widoczny podczas ogrzewania do 660 K. Powyżej tej temperatury pik ten zmniejsza się ze wzrostem piku Zenera. Jeśli uporządkowaną strukturę uzyskuje się przez powolne ogrzewanie próbki, która wcześniej została schłodzona w stanie nieuporządkowanym, to żaden pik o niskiej częstotliwości nie jest widoczny w widmie izotermicznym, a tylko obserwuje się o wiele niższe tło, które jeszcze bardziej zmniejsza się aż do ponownego pojawienia się piku Zenera. Relaksacje przy niskiej częstotliwości prawdopodobnie są spowodowane ruchem granic antyfazowych i bliźniaczych w strukturach uporządkowanych.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 3A; 2093-2096
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Microstructure and Mechanical Properties of Magnesium Alloys Mg-Li-RE After the Process of Casting and Extrusion
Autorzy:
Bednarczyk, I.
Kuc, D.
Mikuszewski, T.
Powiązania:
https://bibliotekanauki.pl/articles/353094.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ultra-light Mg-Li-RE alloys
extrusion process
microstructure
mechanical properties
Opis:
The article presents tests results of the influence of extrusion process on the microstructure and mechanical properties of magnesium alloy with lithium and rare earth elements with symbols LAE442 and LAE842. Microstructures of magnesium alloys after extrusion were compared with microstructure after casting and homogenisation. Presented results show the mechanical properties marked in static compression test in room temperature. It was stated that alloy LAE842 is characterised with better plasticity than the alloy LAE442.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 1; 35-38
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Quantitative Evaluation of the Microstructure and Mechanical Properties of Hot Rolled 23MnB4 Steel Grade for Cold Upsetting
Autorzy:
Kuc, D.
Szala, J.
Bednarczyk, I.
Powiązania:
https://bibliotekanauki.pl/articles/350971.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
23MnB4 steel
hot rolling
microstructure
quantitative metallography
grain size
Opis:
The article presents the results of tests of influence of the thermo-mechanical treatment parameters on the mechanical properties and microstructure of steel 23MnB4 for cold-upsetting. Measurements of the ferrite grains and pearlite colonies were conducted with the use of Met-Ilo program supplemented by additional procedures dedicated to structure analysis of ferritic-pearlitic steel. The process of rolling was conducted in simulation in semi-continuous finishing train arrangement with different temperature and cooling rate. Elaborated procedure of quantitative analysis of microstructure and conducted mechanical properties tests will be used during preparations of modified technologies of wire rod rolling to prepare products made of steel, the microstructure of which is characterised higher utility properties.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2A; 551-556
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Cumulative Plastic Deformation on Microstructure of the Fe-Al Intermetallic Phase Base Alloy
Wpływ skumulowanego odkształcenia plastycznego na strukturę stopów Fe-Al na osnowie faz międzymetalicznych
Autorzy:
Bednarczyk, I.
Kuc, D.
Niewielski, G.
Powiązania:
https://bibliotekanauki.pl/articles/350991.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
FeAl alloy
Max train simulator
cumulative plastic deformation
microstructure
stop Fe-Al
symulator MaxStrain
skumulowane odkształcenie plastyczne
mikrostruktura
Opis:
This article is part of the research on the microstructural phenomena that take place during hot deformation of intermetallic phase-based alloy. The research aims at design an effective thermo - mechanical processing technology for the investigated intermetallic alloy. The iron aluminides FeAl have been among the most widely studied intermetallics because their low cost, low density, good wear resistance, easy of fabrication and resistance to oxidation and corrosion. There advantages create wide prospects for their industrial applications for components of machines working at a high temperature and in corrosive environment. The problem restricting their application is their low plasticity and their brittle cracking susceptibility, hampers their development as construction materials. Consequently, the research of intermetallic-phase-based alloys focuses on improvement their plasticity by hot working proceses. The study addresses the influence of deformation parameters on the structure of an Fe-38% at. Al alloy with Zr, B Mo and C microadditions, using multi – axis deformation simulator. The influence of deformation parameters on microstructure and substructure was determined. It was revealed that application of cumulative plastic deformation method causes intensive reduction of grain size in FeAl phase base alloy.
Prezentowana praca stanowi element prowadzonych badań nad możliwością kształtowania stopów na osnowie faz międzymetalicznych z układu Fe-Al drogą obróbki cieplno-plastycznej. Związki międzymetaliczne są traktowane jako przyszłościowe materiały do pracy w wysokich temperaturach i agresywnych środowiskach korozyjnych. Zainteresowanie tą grupą materiałową jest spowodowane dobrymi właściwościami użytkowymi: dobrą odpornością na utlenianie i korozję w środowisku wody morskiej, zużycie ścierne. Ponadto niskie koszty materiałowe stwarzają perspektywy do zastosowań jako alternatywę dla stali odpornych na korozję. Ograniczeniem możliwości szerokiego zastosowania intermetalików z układu Fe-Al, jest ich niedostateczna plastyczność, będąca czynnikiem hamującym ich dalszy rozwój jako materiałów konstrukcyjnych. Stąd badania nad możliwością poprawy plastyczności droga obróbki cieplno-plastycznej. W artykule analizowano wpływ parametrów odkształcania na mikrostrukturę stopu Fe-38% at. Al z mikododatkami cyrkonu, molibdenu, boru węgla. Z wykorzystaniem symulatora Maxstrain, który umożliwa kumulację dużych odkształceń w materiale. Przeprowadzono badania mikrostuktury i substruktury wykazały istotny wpływ odkształcania tą metodą na rozdrobnienie ziarn w badanym stopie.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 3; 987-991
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of Extrusion in the Complex Strain State on the Microstructure and Mechanical Properties of MgAlZn Magnesium Alloys
Autorzy:
Bednarczyk, I.
Kuc, D.
Tomaszewska, A.
Tkocz, M.
Powiązania:
https://bibliotekanauki.pl/articles/353998.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnesium alloys
KoBo method
microstructure
electron microscope
shape factor
Opis:
The paper presents the results of tests concerning the effect of the extrusion process in the complex strain state on the microstructure and properties of one of magnesium alloy with aluminium, zinc and manganese, designated AZ61. Due to its specific gravity, it is increasingly being used in the automotive and aerospace industries to reduce the weight of structural elements. As a result of plastic deformation processes, rods with a diameter of 8, 6 and 4 mm were obtained from AZ61 magnesium alloy. The microstructure analysis was performed using light and electron microscopy (STEM) techniques in the initial state and afterplastic deformation. Microstructure studies were supplemented with a quantitative analysis using the Metilo program. A number of stereological parameters were determined: average diameter of grain, shape factor. A static tensile test was carried out at 250ºC and 300ºC, at deformation rates of 0.01, 0.001 and 0.0001 m·s-1. Better plastic properties after deformation using KoBo methodwere obtained than with conventional extrusion.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 3; 1121-1128
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Deformation Method on the Microstructure and Properties of Magnesium Alloy WE43
Autorzy:
Bednarczyk, I.
Kuc, D.
Tkocz, M.
Tomaszewska, A.
Powiązania:
https://bibliotekanauki.pl/articles/353617.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnesium alloys
SPD method
microstructure
static tensile test
Opis:
The article presents tests results of the influence of deformation methods on the microstructure and properties of alloy WE43. There were direct extrusion tests and extrusion with KoBo method performed. An assessment of the influence of the methods of deformation on the microstructure and the mechanical properties of the achieved rods from alloy WE43 was conducted. There was an analysis of microstructure carried out with the use of light and scanning microscopy techniques in the initial state and after plastic deformation. Static tensile test was conducted in temperature of 350°C at a speed of 0.0001 m·s-1 and microhardness measurements were performed of HV0.2. On the basis of the achieved mechanical tests results it was stated that in the temperature of 350°C for samples deformed with the use of KoBo method there was an effect of superplastic flow found. The value of elongation achieved was 250% which was 3 times higher than in case of classic extrusion (80%).
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 4; 1975-1980
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and Plastic Properties of Mg-Li Alloys Smelted in Vacuum Induction Furnaces after Hot Working
Autorzy:
Hadasik, E.
Kuc, D.
Mikuszewski, T.
Schindler, I.
Powiązania:
https://bibliotekanauki.pl/articles/356724.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnesium-lithium alloy
research of plasticity
activation energy
hot working microstructure
Opis:
The paper analyses the characteristics of plasticity and microstructure of magnesium alloys with lithium meant for hot plastic working with different lithium content. The alloys were prepared in conditions of vacuum smelting. Achieved ingots were subject to hot extrusion. Tests on Gleeble simulator were conducted to assess the susceptibility of tested alloys to plastic forming in conditions of hot plastic working. For tested alloy the activation energy was marked for hot plastic deformation and plasticity characteristics in function of Zener-Hollomon parameter. After the analysis of the influence of temperature on the deformability of tested alloys it was stated that the alloy containing 8%Li (LAZ831) has better susceptibility to plastic treatment than alloy containing 4%Li (LAZ431), but higher than in case of classic magnesium alloys - AZ31.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 3; 1427-1432
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study of CuO and V2O5 Effect on IR Spectra of Polycrystalline Bismuth Niobate
Autorzy:
Kuźniarska-Biernacka, I.
Lisińska-Czekaj, A.
Czekaj, D.
Powiązania:
https://bibliotekanauki.pl/articles/352587.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
BiNbO4
ceramics
SEM
FTIR spectroscopy
Opis:
Bismuth niobate (BiNbO4) ceramics were fabricated by mixed oxide method and sintered by presureless sintering method. BiNbO4 ceramics doped with V2 O5 additive in amount 0.125 wt%, 0.250 wt% and 1 wt% of was sintered at T = 910°C whereas BiNbO4 ceramics doped with 2 wt% of CuO additive was sintered at T = 890°C and T = 910°C. It was found that V2 O5 additive improved morphology of the ceramic samples. However, the chemical composition of BiNbO4 ceramics in relation to bismuth oxide and niobium oxide manifested a tendency of lack of Bi2 O3 component. Absorption bands for the BiNbO4 compound were identified. FTIR band positions associated with NbO6 octahedra suggested that the crystal structure changes after V2 O5 incorporation.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 2; 817-821
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Extrusion Process on the Microstructure and Mechanical Properties of Magnesium Alloys
Autorzy:
Bednarczyk, I.
Kuc, D.
Tomaszewska, A.
Mrugała, A.
Powiązania:
https://bibliotekanauki.pl/articles/958196.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnesium alloys
microstructure
mechanical properties
process of extrusion method KOBO
Opis:
The article presents the results of plastic shaping tests of AZ61 and WE43 alloys. There were both classic extrusion tests as well as extrusion tests of KOBO method. An assessment was made of the influence of extrusion process parameters on the mechanical properties and the structure of the alloys. On the basis of achieved results of mechanical properties for alloys AZ31 and WE43 the susceptibility of those alloys to plastic shaping was determined. Quantitative tests of structure assessment in case of alloys AZ61 and WE43 after extrusion with the use of KOBO method were conducted with the use of METILO program. It has been shown that extrusion AZ61,WE43 alloys method KOBO leads to considerable fragmentation of grains.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2A; 545-550
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of the Calcination Temperature on the Optical and Mechanical Properties of Y2O3-MgO Nanocomposite
Autorzy:
Yong, S.-M.
Choi, D. H.
Lee, K.
Ko, S.-Y.
Cheong, D.-I.
Powiązania:
https://bibliotekanauki.pl/articles/351252.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
infrared transparent ceramics
Y2O3-MgO nanocomposites
sol-gel combustion synthesis
calcination
spark plasma sintering
Opis:
Y2O3-MgO nanocomposites are one of the most promising materials for hypersonic infrared windows and domes due to their excellent optical transmittance and mechanical properties. In this study, influence of the calcination temperature of Y2O3-MgO nanopowders on the microstructure, IR transmittance, and hardness of Y2O3-MgO nanocomposites was investigated. It was found that the calcination temperature is related to the presence of residual intergranular pores and grain size after spark plasma sintering. The nanopowders calcined at 1000°C exhibits the highest infrared transmittance (82.3% at 5.3 μm) and hardness (9.99 GPa). These findings indicated that initial particle size and distribution of the nanopowders are important factors determining the optical and mechanical performances of Y2O3-MgO nanocomposites.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1481-1484
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improvement of Microstructure and Barrier Properties of Silicate Coatings on Low Carbon Steel by Incorporating Colloidal Nano-SiO2
Autorzy:
Majdi, M. R.
Danaee, I.
Zaarei, D.
Farzam, M.
Powiązania:
https://bibliotekanauki.pl/articles/355960.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
colloidal nano-SiO2
silicate coating
corrosion
AFM
ATR-FTIR
Opis:
Silicate coatings have been considered as an alternative to toxic and carcinogenic other chemical treatments. In this paper, a strengthened silicate coating was formed on the surface of low carbon steel by dip immersion method. The modification and strengthening was done by loading colloidal nano-SiO2 into the film. The characterizations of nano-SiO2 were investigated by FESEM, TEM and FT-IR. The effects of nano contents (weight ratio) and drying temperatures on corrosion properties of silicate film were studied. Potentiodynamic polarization, electrochemical impedance spectroscopy and immersion tests have been used to study corrosion behavior of nano-loaded silicate films. Surface morphology, microstructure and its chemical composition were analyzed by means of FESEM, EDS, AFM, XRD, GIXRD, ATR-FTIR and Raman techniques. Results indicated that colloidal nano-SiO2 properly modified the silicate coatings and significantly improved the corrosion resistance and barrier property. Also drying temperature showed a considerable effect in silicate coating and higher corrosion resistance was obtained with 150°C curing.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 2; 627-638
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Grain Boundary Relaxation in Bi-Crystals: Mechanical Spectroscopy and Molecular Dynamics Simulations
Relaksacja granic ziaren w bikryształach: spektroskopia mechaniczna i symulacje metodą dynamiki molekularnej
Autorzy:
Maier, A.-K.
Mari, D.
Tkalcec, I.
Schaller, R.
Powiązania:
https://bibliotekanauki.pl/articles/353074.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
internal friction grain boundaries
gold alloys
molecular dynamics
granice wewnętrzne tarcia ziarna
stop złota
dynamika molekularna
Opis:
Different Au-Ag-Cu samples have been studied by mechanical spectroscopy. Both polycrystals and bi-crystals show a relaxation peak at 800 K, accompanied by an elastic modulus change. Since this peak is absent in single crystals it is related to the presence of grain boundaries. Molecular dynamics simulations reveal two microscopic mechanisms, when a shear stress is applied onto a Σ5 grain boundary: at 700 K, the boundary migrates perpendicularly to the boundary plane under an external stress. At 1000 K, only sliding at the boundary is observed. These two mechanisms acting in different temperature intervals are used to model the mechanic response of a polycrystal under an applied stress. The models yield expressions for the relaxation strength Δ and for the relaxation time τ as a function of the grain size. A comparison with the mechanical spectroscopy measurements of polycrystals and the bi-crystals show that the grain boundary sliding model reproduces correctly the characteristics of the grain boundary peak.
Różne próbki ze stopów Au-Ag-Cu badano metodą spektroskopii mechanicznej. Zarówno w polikryształach, jak i bikryształach występuje pik relaksacyjny w temperaturze 800 K, któremu towarzyszy zmiana modułu sprężystości. Ponieważ pik ten nie występuje w monokryształach to jego występowanie wiązane jest z obecnością granic ziaren. Symulacje dynamiki molekularnej ujawniają dwa mikroskopowe mechanizmy, gdy naprężenie ścinające jest przyłożone do granicy ziarna Σ5: w temperaturze 700 K, granica przemieszcza się prostopadle do płaszczyzny granicznej pod wpływem zewnętrznego naprężenia. W 1000 K, obserwuje się tylko poślizg po granicy. Te dwa mechanizmy działające w różnych zakresach temperatur są używane do modelowania mechanicznej reakcji polikryształu na przyłożone naprężenie. Modele podają wyrażenie na stopień relaksacji Δ i czas relaksacji τ w funkcji wielkości ziaren. Porównanie z wynikami badań polikryształów i bikryształów uzyskanych metodą spektroskopii mechanicznej pokazuje, że model poślizgu granicy ziarna poprawnie odtwarza charakterystykę piku pochodzącego od granic ziaren.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 1; 377-380
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics of plasticity and microstructure of hot forming magnesium alloys Mg-Al-Zn type
Charakterystyki plastycznosci i mikrostruktura odkształcanych na gorąco stopów magnezu typu Mg-Al-Zn
Autorzy:
Kuc, D.
Hadasik, E.
Schindler, I.
Kawulok., P.
Śliwa, R.
Powiązania:
https://bibliotekanauki.pl/articles/350870.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stop magnezu
badania plastyczności
mikrostruktura
energia aktywacji
magnesium alloy
research of plasticity
microstructure
dynamic recrystallization
activation energy
Opis:
The paper presents analysis of plasticity characteristics and microstructure of magnesium alloys for hot plastic treatment with different aluminium content (3÷8%). Tests were conducted for assessment of susceptibility of tested alloys to hot plastic deformation. A tensile test was run in temperature from 250 to 450°C. Based on the results, ultimate tensile strength (UTS) and reduction of area (Z) were determined for samples. Conducted compression tests allowed to specify the flow stress and microstructure changes after deformation. The activation energy in hot forming was determined for investigated alloys. The parameters of the process where flow is significantly influenced by twin formation in microstructure were determined. A varied plasticity of tested alloys was found depending on aluminium content. Test results will be useful in development of forging technology of selected construction elements which serve as light substitutes for currently used materials.
W pracy analizowano charakterystyki plastyczności i mikrostrukturę stopów magnezu przeznaczonych do przeróbki plastycznej na gorąco ze zróżnicowana zawartością aluminium (3-8%). Badania prowadzono dla oceny podatności badanych stopów do kształtowania plastycznego w warunkach przeróbki plastycznej na gorąco. Przeprowadzono próbę rozciągania w temperaturze od 250 do 450 st.C, na podstawie której określono wytrzymałość na rozciąganie i przewężenie badanych próbek. Wykonane próby ściskania pozwoliły na wyznaczenie naprężenia uplastyczniajacego i zmian mikrostruktury po odkształceniu. Dla badanych stopów wyznaczono energię aktywacji odkształcenia plastycznego na gorąco. Określono parametry procesu, dla których na przebieg plastycznego płynięcia wpływa istotnie bliźniakowanie w mikrostrukturze. Wykazano zróżnicowaną plastyczność badanych stopów w zależności od zawartości aluminium. Wyniki badań będą pomocne do opracowania technologii kucia wybranych elementów konstrukcyjnych stanowiących lekkie zamienniki stosowanych obecnie materiałów.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 1; 151-156
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Diversification of Intermetallic Zn Phases Growth on Steel During Hot-Dip Galvanizing
Autorzy:
Węgrzynkiewicz, S.
Jędrzejczyk, D.
Szłapa, I.
Hajduga, M.
Boczkal, S.
Powiązania:
https://bibliotekanauki.pl/articles/352256.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hot-dip zinc galvanizing
heat-affected zone
softening annealing
oxy-acetylene cutting
Opis:
The steel substrate formed as the result of oxy-acetylene cutting (OAB) was treated differently - using: softening annealing, grinding and electro-polishing. Investigations were focused on the influence of additional processing on the structure and corrosion resistance of the deposited zinc coating. The hot - dip Zn galvanizing process was conducted in industrial conditions. Parameters were fixed: temperature 457 °C, dipping time 150 s. The coating thickness diversification dependent on the sub-surface steel structure was analysed and compared to the previous results. The correlation between conducted treatment and coatings morphology was determined.
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 2A; 515-520
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of a Substrate Surface on the (Zn) : Coating Formation
Wpływ powierzchni podłoża na kształtowanie się powłoki (Zn)
Autorzy:
Węgrzynkiewicz, S.
Jędrzejczyk, D.
Szłapa, I.
Hajduga, M.
Boczkal, S.
Powiązania:
https://bibliotekanauki.pl/articles/352854.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hot-dip Zn galvanizing
heat-affected zone (HAZ)
water jet cutting
oxyacetylene cutting
laser cutting
cynkowanie ogniowe Zn
strefa wpływu ciepła (HAZ)
cięcie strumieniem wody
cięcie tlenowo-acetylenowe
cięcie laserem
Opis:
The steel substrate was cut by means of different methods, like water jet, laser or oxyacetylene blowpipe. So, some different surfaces (after cutting / without cutting) were subjected to the (Zn) - hot dip galvanizing. The galvanizing process was performed in industrial conditions by applying the constant temperature equal to 457°C, and a dipping time equal to 150 s. The (Zn) - coating morphologies and sub-layer thicknesses were analyzed to explain some expected differences in the coatings formation.
W prezentowanej pracy podłoże stalowe cięto stosując różne metody: strumień wody, laser, palnik acetylenowo-tlenowy. W wyniku tego otrzymano zróżnicowaną powierzchnię (po cięciu/bez cięcia), która poddano cynkowaniu ogniowemu. Proces cynkowania wykonywano w warunkach przemysłowych stosując stałe parametry: temperaturę 457°C, czas zanurzenia t=150 s. W trakcie badań analizowano morfologię powłoki cynkowej oraz grubości poszczególnych podwarstw w celu wyjaśnienia różnic w narastaniu powłok.
Źródło:
Archives of Metallurgy and Materials; 2014, 59, 4; 1373-1378
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies