Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "slag sand" wg kryterium: Temat


Wyświetlanie 1-2 z 2
Tytuł:
Casting defects analysis by the Pareto method
Autorzy:
Borowiecki, B.
Borowiecka, O.
Szkodzińska, E.
Powiązania:
https://bibliotekanauki.pl/articles/381830.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
casting defect
Pareto analysis
slag inclusions
sand hole
wada odlewu
analiza Pareto
wtrącenia żużlowe
Opis:
On the basis of receive results formed of diagram Pareto Lorenz. On the basis of receive graph it affirmed, that for 70% general number casting defects answered 3 defects (9 contribution – 100% defects). For 70% general number defects of influence it has three type of causes: sand holes, porosity and slag inclusions. The defects show that it is necessary to take up construction gating system. The remaining 8 causes have been concerned only 25%, with general number of casting defects. Analysis of receive results permit to determine of direction of correct actions in order to eliminate or to limit the most defects.
Źródło:
Archives of Foundry Engineering; 2011, 11, 3 spec.; 33-36
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure, SDAS and Mechanical Properties of A356 alloy Castings Made in Sand and Granulated Blast Furnace Slag Moulds
Autorzy:
Jinugu, B. R.
Inampudi, N. M.
Powiązania:
https://bibliotekanauki.pl/articles/379468.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
silica sand
slag
CO2 process
casting aluminium alloys
SEM-EDX
mechanical properties
piasek kwarcowy
żużel
proces CO2
odlew ze stopów aluminium
właściwości mechaniczne
Opis:
Investigations were carried out to ensure the granulated blast furnace (GBF) slag as an alternative mould material in foundry industry by assessing the cast products structure property correlations. Sodium silicate-CO2 process was adopted for preparing the moulds. Three types of moulds were made with slag, silica sand individually and combination of these two with 10% sodium silicate and 20 seconds CO2 gassing time. A356 alloy castings were performed on these newly developed slag moulds. The cast products were investigated for its metallography and mechanical properties. Results reveal that cast products with good surface finish and without any defects were produced. Faster heat transfers in slag moulds enabled the cast products with fine and refined grain structured; and also lower Secondary Dendrite Arm Spacing (SDAS) values were observed than sand mould. Slag mould casting shows improved mechanical properties like hardness, compression, tensile and impact strength compared to sand mould castings. Two types of tensile fracture modes, namely cleavage pattern with flat surfaces representing Al−Si eutectic zone and the areas of broken Fe-rich intermetallic compounds which appear as flower-like morphology was observed in sand mould castings. In contrast, GBF slag mould castings exhibit majority in dimple fracture morphology with traces of cleavage fracture. Charpy impact fractured surfaces of sand mould castings shows both transgranular and intergranular fracture modes. Only intergranular fracture mode was noticed in both GBF slag and mixed mould castings.
Źródło:
Archives of Foundry Engineering; 2017, 17, 1; 179-191
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies