Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Kowalik, Przemysław" wg kryterium: Autor


Wyświetlanie 1-2 z 2
Tytuł:
Assessment of Tribological Properties of Single- and Double-Layer Pad Coatings Deposited onto Cultivator Points
Autorzy:
Wójcik, Wiesław
Barszcz, Marcin
Dziedzic, Krzysztof
Kuzioła, Jarosław
Kowalik, Przemysław
Powiązania:
https://bibliotekanauki.pl/articles/958001.pdf
Data publikacji:
2019
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
wear
friction
coatings
welding
zużycie
tarcie
powłoki
spawanie
Opis:
This paper investigates properties of single- and double-layer pad coatings deposited on cultivator points. The coatings were deposited by manual metal arc welding (MMA) with ESAB OK. 84.58 coated electrodes using an inverter welder, DEDRA DESi201. Tribological properties were determined with a THT 1000 tribometer. A ball-on-disc friction pair was used. Experiments were performed in room temperature, with the sliding speed set equal to 0.3 m/s and two loads: 5 and 20 N. In addition, hardness was measured on the surface and in the cross section of samples by a Rockwell hardness test method (scale C). Surface roughness was measured before and after friction, and post-friction surface topography was examined under microscope. Impact strength tests of the coatings with single- and double layers of pads were performed. The tools and IT algorithms were used to collect and process the results of experimental research.
Źródło:
Advances in Science and Technology. Research Journal; 2019, 13, 3; 120-128
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Case Study of Composite Chassis Manufacturing Process Using Low Temperature Molds Tempered with Gradual Heat Annealing Process
Autorzy:
Rządkowski, Witold
Klik, Przemysław
Tracz, Jan
Kowalik, Michał
Powiązania:
https://bibliotekanauki.pl/articles/2201751.pdf
Data publikacji:
2022
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
monocoque
manufacturing
out-of-autoclave
manufacturing process
gradual heat annealing
Opis:
This case study describes a manufacturing process of composite chassis also known as monocoque. The structure is made using carbon fibre reinforced polymers (CFRP) which are manufactured in out-of-autoclave (OOA) process from pre-impregnated carbon fabrics and aluminium alloy honeycomb core. Since the material cost is high the aim of the project was to reduce the cost of manufacturing process i.e. cost of models and moulds. Therefore, instead of high-temp models and moulds a cheaper alternative was used. It consisted of Styrofoam models made using polyurethane (PU) paste and moulds made from CFRP using wet layup process which were cured at room temperature. Such moulds had to be adapted to withstand high temperatures during pre-preg cure. This was done with gradual heat annealing process which increased the maximum service temperature from 45C to 90C. This was enough for the low-temp cure of pre-preg material, but it might be possible to increase the temperature even further. As a result, the cost of manufacturing process had been reduced by 50%.
Źródło:
Advances in Science and Technology. Research Journal; 2022, 16, 3; 12--21
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies