Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Sidun, J." wg kryterium: Autor


Wyświetlanie 1-3 z 3
Tytuł:
Porównawcza analiza biomechaniczna wybranych systemów stabilizacji transpedikularnej
A comparative analysis of selected transpedicular stabilization systems
Autorzy:
Sajewicz, E.
Koronkiewicz, T.
Sidun, J.
Powiązania:
https://bibliotekanauki.pl/articles/386897.pdf
Data publikacji:
2008
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
stabilizacja transpedikularna
analiza biomechaniczna
transpedicular stabilization
analysis
Opis:
Prezentowane w pracy wyniki dają odpowiedź na pytanie dotyczące wpływu podatności lędźwiowego odcinka kręgosłupa na jakość stabilizacji transpedikularnej. Przedstawiono wyniki badań przemieszczeń odcinka lędźwiowego kręgosłupa poddanego jednocześnie kompresji i zginaniu (mimośrodowe ściskanie). Badano przemieszczenia kręgu L3 dziewięciu preparatów ustabilizowanych za pomocą systemów Socon, Omega oraz Bial-Stab, a następnie pomiary powtarzano po wykonaniu korporektomii na poziomie L3. Wyniki badań porównywano z wynikami uzyskanymi na preparatach nieustabilizowanych. Wykazano, że brak ciągłości przedniej kolumny kręgosłupa nie wpływa na biomechaniczną jakość stabilizacji w zakresie stosowanych obciążeń. Wyniki analizy statystycznej jednoznacznie wskazują, że podatność kręgosłupa na obciążenia wpływa w sposób istotny na wartości przemieszczeń po stabilizacji przeznasadowej. Nie zaobserwowano istotnych statystycznie różnic w jakości stabilizacji pomiędzy poszczególnymi systemami.
In the paper the results of influence of lumbar spine flexibility on quality of transpedicular stabilization are presented. In particular, measurements of displacements of the lumbar spine subjected to simultaneous compression and bending (eccentric compression) are shown. The displacements were measured at L3 level in nine lumbar specimens stabilized by means of Socon, Omega and Bial-Stab systems. The obtained results were compared with the results of measurements carried out on the specimens without stabilization. It was also shown that a lack of continuity of the anterior column did not influence on quality of the stabilizations in the range of the used loading. The statistical analysis showed that lumbar flexibility sufficiently influenced on the displacements of the fixed lumbar spine. No statistical differences were observed between of the systems used as regards their biomechanical performance.
Źródło:
Acta Mechanica et Automatica; 2008, 2, 1; 69-72
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fretting Wear of Materials – Methodological Aspects of Research
Autorzy:
Kulesza, E.
Dąbrowski, J. R.
Sidun, J.
Neyman, A.
Mizera, J.
Powiązania:
https://bibliotekanauki.pl/articles/386945.pdf
Data publikacji:
2012
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
cierność materiałów
zużycie
material fretting
fretting wear
Opis:
In this article, methodical aspects of studies on material fretting wear have been presented. The results of studies conducted on a “pin on disc” type device made at the Department of Materials and Biomedical Engineering of the Bialystok University of Technology confirmed the decisive influence of the amplitude of oscillations and the load value on the course and nature of the process. At a constant value of load, the course of resistance to motion was dependent on the amplitude. Increasing the amplitude of oscillations caused a change in friction conditions: from static friction (elastic deformation of formed adhesive connections, without dislocation of cooperating elements) to kinetic friction (breaking of adhesive bridges and displacement with sliding). The increase of the load value at a constant amplitude value caused a change in the course and nature of resistance to motion from sliding friction to friction at-rest.
Źródło:
Acta Mechanica et Automatica; 2012, 6, 3; 58-61
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Verification of ram-press pipe bending process using elasto-plastic fem model
Autorzy:
Sidun, J.
Łukaszewicz, A.
Powiązania:
https://bibliotekanauki.pl/articles/386877.pdf
Data publikacji:
2017
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
pipe bending
FEM analysis
finite element method
Opis:
In this paper selected aspects of numerical modelling of bending pipes process are described. Elasto-plastic material model was used in COMSOL FEM environment. The results of numerical analyses of two kinds of steel were presented. The correctness of the proposed model was verified based on comparison shapes of deformed pipe profile obtained at the ending step of bending both from numerical simulations and experiment.
Źródło:
Acta Mechanica et Automatica; 2017, 11, 1; 47-52
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies