Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Rintala, L." wg kryterium: Autor


Wyświetlanie 1-4 z 4
Tytuł:
Applicability of published experimental works as a knowledge source in recommendation of gold ore processing workflows
Autorzy:
Rintala, L.
Aromaa, J.
Forsen, O.
Powiązania:
https://bibliotekanauki.pl/articles/109780.pdf
Data publikacji:
2015
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
gold ore
leaching
case-based reasoning
process development
Opis:
The experimental work is the most time consuming and expensive part of the process design. A case-based reasoning (CBR) methodology can be used to assist in the process design. Auric Adviser is a CBR system under development for recommendation of gold ore processing workflows. In Auric Adviser the knowledge in gold ore processing is represented in two models. The first model holds the knowledge needed to recommend process chains already used in industry. The second knowledge model is intended to recommend the most efficient unit processes based on research results. The objective of this study was to analyse the information richness of journal articles and other publications concerning single process steps of gold extraction. The aim was to study the applicability of these publications as a source for the second Auric Adviser knowledge model. In this study, 25 publications concerning leaching of gold were analysed and information was extracted in a case base. The case base was taken as either a process or experimental description with clearly defined differences to other descriptions. In total, 218 cases that described results of gold leaching were extracted from the sources. The analysis of descriptions showed that the knowledge necessary for design the second Auric Adviser model can be elicited from journal articles and other publications concerning single process steps. The trends in the case description were that the gold content and process outcome were usually well described. Nevertheless, the information richness varied in descriptions of raw materials, experimental arrangements but the results were often missing details. The incompleteness of information causes challenges in the process comparison although it does not prevent the CBR system to work.
Źródło:
Physicochemical Problems of Mineral Processing; 2015, 51, 2; 707-717
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dissolution of gold with cyanide replacingreagents
Autorzy:
Aromaa, J.
Rintala, L.
Kahari, M.
Forsen, O.
Powiązania:
https://bibliotekanauki.pl/articles/109410.pdf
Data publikacji:
2015
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
gold leaching
ammonium thiosulfate
chloride
thiourea
thiocyanate
Opis:
Cyanide is used in the leaching phase of hydrometallurgical recovery of gold. The toxicity and environmental risks have created a need for safer alternatives. There is a vast amount of information about gold extraction and a selection has been collected and formalized to be used in a decision support tool. The tool Auric Advisor uses case-based reasoning (CBR) to provide process alternatives for the user queries. The aim of this paper is to study leaching of gold with cyanide replacing alternatives such as ammonium thiosulfate, chloride-hypochlorite, thiourea and thiocyanate to provide new cases for the tool. The behaviour of gold was examined with electrochemical tests and weight loss measurements a using quartz crystal microbalance (QCM) were used to determine the dissolution rate. Based on literature, the dissolution rate determined for cyanide solution was 2.5 mgcm-2h-1. Based on polarisation experiments and potential measurements, the ammonium thiosulfate system with cupric ion as oxidant was estimated to dissolve gold slower than cyanide. In the QCM tests the chloride-hypochlorite alternative showed highest dissolution rate of 8.6 mgcm-2h-1 at the redox potential of 900 mV vs. SHE. The thiocyanate system with ferric ion dissolved gold at a rate of 3.4 mgcm-2h-1 at the redox potential of 620 mV vs. SHE. Thiourea system with ferric ion showed the dissolution rate of 1.65 mg cm-2 h-1 at the redox potential of 450 mV vs. SHE. The results of the rapid tests were comparable with literature and were included in the case base of the Auric Advisor decision-support tool.
Źródło:
Physicochemical Problems of Mineral Processing; 2015, 51, 1; 269-279
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thiosulfate-copper-ammonia leaching of pure gold and pressure oxidized concentrate
Autorzy:
Porvali, A.
Rintala, L.
Aromaa, J.
Kaartinen, T.
Forsen, O.
Lundstrom, M.
Powiązania:
https://bibliotekanauki.pl/articles/110672.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
gold leaching
thiosulfate
quartz crystal microbalance
Opis:
In this research cyanide-free leaching of pure gold and pressure oxidized refractory gold concentrate by thiosulfate-copper-ammonia solutions were examined. A quartz crystal microbalance (QCM) was used to study gold leaching as a factorial series where the best gold leaching rate (2.987 mg/(cm2∙h)) was achieved with a solution consisting of 0.2 M (NH4)2S2O3, 1.2 M NH3, 0.01 M CuSO4 and 0.4 M Na2SO4. Temperature had the greatest effect on the gold leaching rate. An increase in thiosulfate concentration (0.1–0.2 M) increased gold dissolution. The combined effect of temperature and ammonia concentration had a statistically significant effect on the gold leaching rate at 0.1 M M2S2O3. Combination of applied potential and NH3:S2O3 ratio had a statistically significant effect on the gold leaching rate at 0.2 M M2S2O3. An increase in applied potential decreased the gold dissolution rate at low ammonia concentrations but increased it at high concentrations. A pressure oxidized gold concentrate was leached for 6 hours in the batch reactor leaching experiments. The effect of rotative velocity (1.26–1.56 m/s) and slurry density (10–30 wt%) was investigated at the following leaching parameters: 0.2 M Na2S2O3, 0.6 M NH3, 0.01 M CuSO4, 0.4 M Na2SO4. Lower slurry density (10 wt%) resulted in a higher Au leaching efficiency. An increase in the rotation rate did not have an effect on the final Au leaching recovery. The best Au leaching efficiency (89%) was achieved with 590 rpm mixing, 1.56 m/s rotative velocity and 10 wt% slurry density.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 2; 1079-1091
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Models for viscosity and density of copper electrorefining electrolytes
Autorzy:
Kalliomaki, T.
Aji, A. T.
Rintala, L.
Aromaa, J.
Lundstrom, M.
Powiązania:
https://bibliotekanauki.pl/articles/109549.pdf
Data publikacji:
2017
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
copper electrorefining
viscosity model
density model
Opis:
Viscosity and density of copper electrorefining electrolytes affect energy consumption and purity of cathode copper. Decreasing the viscosity and density increases the rate of falling of the anode slimes to the bottom of an electrorefining cell and increases the diffusivity and mobility of ions. Increasing the falling rate of the anode slimes decreases a risk of anode slime impurities ending up on the cathode and being entrapped into the copper deposit. This work introduces two new models for both viscosity and density of copper electrorefining electrolytes with high accuracy and one reconstructed improved model for some electrorefining data of viscosity published previously. The experimental work to build up these new models was carried out as a function of temperature (50, 60, 70 °C), copper (40, 50, 60 g/dm3), nickel (0, 10, 20 g/dm3) and sulfuric acid (130, 145, 160 g/dm3) concentrations for all models, and additionally arsenic concentration (0, 15, 30, 32, 64 g/dm3) was included in the viscosity models. Increasing concentrations of Cu, Ni, As and H2SO4 were found to increase the viscosity and density, whereas increasing temperature decreased both viscosity and density. The viscosity models were validated with industrial electrolyte samples from the Boliden Harjavalta Pori tankhouse. The experimental and modeling work carried out in this study resulted in improved viscosity models, having the strongest agreement with the industrial electrorefining electrolytes.
Źródło:
Physicochemical Problems of Mineral Processing; 2017, 53, 2; 1023-1037
1643-1049
2084-4735
Pojawia się w:
Physicochemical Problems of Mineral Processing
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-4 z 4

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies