Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Kumar, S." wg kryterium: Autor


Tytuł:
Flood risk zoning of Satluj River Basin, Himachal Pradesh, India
Autorzy:
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/11273.pdf
Data publikacji:
2015
Wydawca:
Przedsiębiorstwo Wydawnictw Naukowych Darwin / Scientific Publishing House DARWIN
Opis:
Increasing intensity and frequency of rainfall coupled with gradual retreating of glaciers due to climate change in Himalayan region likely to increase the risk of floods. A better understanding of risk zones which are vulnerable to flood disasters can be evolved from the detailed studies on slope, geomorphology and land use/ land cover pattern. Information of these parameters is an important input for the identification of vulnerable areas. Flood risk maps provide useful information about places that may be at risk from flooding. It offers a cost-effective solution for planning, management and mitigation strategies in risky areas. Traditional methods of flood risk mapping are based on ground surveys and aerial observations, but when the phenomenon is widespread, such methods are time consuming and expensive. The possible combination of DEM and other maps of area using an overlay operation method within the Geographical Information System (GIS) platform can lead to derivation and the understanding of spatial association between various parameters which could be used to predict flood risk zones. The study area i.e. Satluj River Basin has been broadly divided into five risk zones viz., very low, low, moderate, high and very high which helped to differentiate between areas that are at risk of different intensities of flood. The very high flood risk zone covers only 3.25 % of total study area, while the very low risk zone covers 13.63 %. The area falls within the very high and high risk constitutes 9.52 % of total basin area. Domain of moderate risk covers an area of 30.66 %. But the maximum area of river basin is constituted by low risk zone i.e. 46.19 %. Identification of such zones will help in timely adopting of mitigation and adaptation measures. Preparation of flood risk zoning maps also helps in regulating indiscriminate and unplanned land use practices in risky areas.
Źródło:
International Letters of Natural Sciences; 2015, 40
2300-9675
Pojawia się w:
International Letters of Natural Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Trend analysis of flood peaks in lower reaches of Satluj River, Himachal Pradesh, India
Autorzy:
Kumar, S.
Santosh, ---
Powiązania:
https://bibliotekanauki.pl/articles/970628.pdf
Data publikacji:
2015
Wydawca:
Przedsiębiorstwo Wydawnictw Naukowych Darwin / Scientific Publishing House DARWIN
Tematy:
flood peaks
mann-kendall test
satluj river basin
regression
trend analysis.
Opis:
Climate change arising from anthropogenic driven emissions of greenhouse gases has emerged as one of the most important environmental issues in the last two decades. One of the most significant potential consequences of climate change may be alteration in regional hydrological cycle and river flow regimes. Increased temperature is expected to increase the peak flows in snowfed rivers of Himalayas. The changing pattern of regional temperature on flood peaks deserves urgent and systematic attention over a basin which provides an insight view of historical trends. Lower reaches of Satluj River is selected for the present study. Testing the significance of observed trends in flood peaks has received a great attention recently, especially in connection with climate change. The data series available was 48 years (1967-2010). The records were subjected to trend analysis by using both non-parametric (Mann-Kendall test) and parametric (linear regression analysis) procedures. For better understanding of the observed trends, flood peaks were computed into standardised flood peak indices (SFPI). These standardised data series were plotted against time and the linear trends observed were represented graphically. The analysis of flood peaks at different observation stations in lower reaches of Satluj River showed a large variability in the trends and magnitudes. The trend analysis results of flood peaks and gauge heights indicate that the flood peaks at all sites i.e. Rampur, Suni and Kasol show increasing but statistically insignificant trends. The trends in gauge height at all sites are also showing increasing trend but Kasol is statistically significant at 95% confidence level. The fast melting of glaciers, incessant monsoon rainfall and the synchronisation of the discharge peaks are the main causes of river floods. The past flood peaks will help us to observe the frequency of occurrence of floods in certain region and to determine whether the flood peaks in the past have been same with that of the present or whether there is any deviation in the trend in relation to climate change. Such studies will help in designing mitigation and adaptation strategies towards extreme hydrological events.
Źródło:
International Letters of Natural Sciences; 2015, 46
2300-9675
Pojawia się w:
International Letters of Natural Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructural considerations on SH-wave propagation in a piezoelectric layered structure
Autorzy:
Goyal, R.
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/280348.pdf
Data publikacji:
2018
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
SH-wave
piezoelectricity
couple stress
characteristic length
Opis:
Shear wave based acoustic devices are being used in gaseous and liquid environments because of their high-sensitivity. The theoretical study of horizontally polarized shear (SH) waves in a layered structure consisting of a piezoelectric ceramic of P ZT − 5H or BaT iO3 material overlying a couple stress substrate is presented in this paper. The considered substrate is supposed to be exhibiting microstructural properties. The closed form expression of dispersion relations are derived analytically for electrically open and short conditions. The effects of internal microstructures of the couple stress substrate, thickness of P ZT − 5H or BaT iO3 ceramic, piezoelectric and dielectric constants are illustrated graphically on the phase velocity of the piezoelectric layer under electrically open and short conditions.
Źródło:
Journal of Theoretical and Applied Mechanics; 2018, 56, 4; 993-1004
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Controllability of semilinear systems with fixed delay in control
Autorzy:
Kumar, S.
Sukavanam, N.
Powiązania:
https://bibliotekanauki.pl/articles/952777.pdf
Data publikacji:
2015
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
first order delay system
mild solution
fixed point
exact controllability
Opis:
In this paper, different sufficient conditions for exact controllability of semilinear systems with a single constant point delay in control are established in infinite dimensional space. The existence and uniqueness of mild solution is also proved under suitable assumptions. In particular, local Lipschitz continuity of a nonlinear function is used. To illustrate the developed theory some examples are given.
Źródło:
Opuscula Mathematica; 2015, 35, 1; 71-83
1232-9274
2300-6919
Pojawia się w:
Opuscula Mathematica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of UPFC for enhancement of voltage profile and minimization of losses using Fast Voltage Stability Index (FVSI)
Autorzy:
Kumar, S.
Renuga, P.
Powiązania:
https://bibliotekanauki.pl/articles/140514.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
flexible AC transmission system (FACTS)
real and reactive power
Unified Power Flow Controller (UPFC)
Bacterial Foraging (BF) algorithm
Opis:
Transmission line loss minimization in a power system is an important research issue and it can be achieved by means of reactive power compensation. The unscheduled increment of load in a power system has driven the system to experience stressed conditions. This phenomenon has also led to voltage profile depreciation below the acceptable secure limit. The significance and use of Flexible AC Transmission System (FACTS) devices and capacitor placement is in order to alleviate the voltage profile decay problem. The optimal value of compensating devices equires proper optimization technique, able to search the optimal solution with less computational burden. This paper presents a technique to provide simultaneous or individual controls of basic system parameter like transmission voltage, impedance and phase angle, thereby controlling the transmitted power using Unified Power Flow Controller (UPFC) based on Bacterial Foraging (BF) algorithm. Voltage stability level of the system is defined on the Fast Voltage Stability Index (FVSI) of the lines. The IEEE 14-bus system is used as the test system to demonstrate the applicability and efficiency of the proposed system. The test result showed that the ocation of UPFC improves the voltage profile and also minimize the real power loss.
Źródło:
Archives of Electrical Engineering; 2012, 61, 2; 239-250
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Comparison of Muscular Activity Involved in the Use of Two Different Types of Computer Mouse
Autorzy:
Kumar, R.
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/90400.pdf
Data publikacji:
2008
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
muscular activity
EMG
computer mouse
Opis:
Two types of computer input devices, a conventional mouse and a roller bar one, were studied in terms of muscular activitiy in m. trapezius dexter, m. deltoideus anterior dexter and m. extensor digitorum dexter, and comfort rating. Fifteen university students and employees participated in this study. The order of the devices was random. While a task was performed, electromyography (EMG) data were recorded for each test. Muscular activity was found to be significantly lower for the roller bar mouse than for the conventional one. Comfort rating indicated there was a significant difference in moving a cursor with the conventional mouse compared to the roller bar one. It is concluded that a roller bar mouse allowed the subjects to work closer to the body compared to the conventional one, thus the former can be recommended as a general means of reducing upper extremity musculoskeletal disorders.
Źródło:
International Journal of Occupational Safety and Ergonomics; 2008, 14, 3; 305-311
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of Ergonomic Risk Assessment Output in Four Sawmill Jobs
Autorzy:
Jones, T.
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/90305.pdf
Data publikacji:
2010
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
physical ergonomics
exposure assessment
musculoskeletal risk assessment
job analysis
prevention and control
Opis:
The objectives of this study were to examine the agreement between 5 ergonomic risk assessment methods calculated on the basis of quantitative exposure measures and to examine the ability of the methods to correctly classify 4 at risk jobs. Surface electromyography and electrogoniometry were used to record the physical exposures of 87 sawmill workers performing 4 repetitive jobs. Five ergonomic risk assessment tools (rapid upper limb assessment [RULA], rapid entire body assessment [REBA], American conference of governmental industrial hygienist’s threshold limit value for mono-task hand work [ACGIH TLV], strain index [SI], and concise exposure index [OCRA]) were calculated. Dichotomization of risk to no risk and at risk resulted in high agreement between methods. Percentage of perfect agreement between methods when 3 levels of risk were considered was moderate and varied by job. Of the methods examined, the RULA and SI were best (correct classification rates of 99 and 97% respectively). The quantitative ACGIH-TLV for mono-task hand work and Borg scale were worst (misclassification rates of 86 and 28% respectively).
Źródło:
International Journal of Occupational Safety and Ergonomics; 2010, 16, 1; 105-111
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Biomechanical Loads and Subjective Stress Exposure to Lumber Graders in Sawmill Industry
Autorzy:
Jones, T.
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/90791.pdf
Data publikacji:
2011
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
job analysis
lumber graders
wood product manufacturing
repetitive strain
upper extremity
physical and psychophysical stress
Opis:
The aim of this study was to determine biomechanical loads and subjective stresses on lumber graders and associated morbidity in a high risk and repetitive sawmill occupation. The exposures of all 29 male sawmill worker volunteers were recorded. Motion and posture were studied with electrogoniometers, muscle loads were recorded with surface electromyography, and psychophysical stresses were assessed with subjective responses. Fifty-nine percent of the participants reported greater than moderate discomfort in their taskdominant upper extremity. Job performance required an average range of motion of 44º, 21º, and 52º in flexion/extension, radial/ulnar deviations, and pronation/supination respectively. It also required an average of 9% maximum voluntary contraction force and was repeated an average of 34 times/min. This repetitive exertion over an 8-h shift was deemed to be a significant risk factor associated with prevalent upper extremity morbidity.
Źródło:
International Journal of Occupational Safety and Ergonomics; 2011, 17, 1; 87-97
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dispersion of Rayleigh Waves in a Microstructural Couple Stress Substrate Loaded with Liquid Layer Under the Effects of Gravity
Autorzy:
Sharma, V.
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/947783.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
couple stress theory
Rayleigh waves
gravity
characteristic length
liquid loading
Opis:
Bone loss is one of the serious health issues in bedridden patients or young generation due to lack of physical activities. Mechanical forces are exerted on the bones through ground reaction forces, liquid loadings and by other contraction activities of the muscles. We are assuming an isotropic half-space with mechanical properties equivalent to that of bone exhibiting microstructures. Consistent couple stress theory introduces an additional material parameter called characteristic length which accounts for inner microstructure of the material. Dispersion relations for leaky Rayleigh waves are derived by considering a model consisting of couple stress half space under the effects of gravity and loaded with inviscid liquid layer of finite thickness or a liquid half space. Impact of the gravity, liquid loadings and microstructures of the material are investigated on propagation of leaky Rayleigh type waves. Phase velocity of leaky Rayleigh waves is studied for five different values of characteristic length parameter which are of the order of internal cell size of the considered material. Variations in phase velocity of leaky Rayleigh waves are also studied under the effect of gravity parameter and thickness of liquid loadings.
Źródło:
Archives of Acoustics; 2018, 43, 1; 11-20
0137-5075
Pojawia się w:
Archives of Acoustics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dispersion of SH waves in a viscoelastic layer imperfectly bonded with a couple stress substrate
Autorzy:
Sharma, V.
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/949130.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
SH waves
couple stress theory
imperfect bonding
characteristic length
viscoelasticity
Opis:
The paper deals with propagation of SH waves in a viscoelastic layer over a couple stress substrate with imperfect bonding at the interface. A dispersion equation of SH waves in a viscoelastic layer overlying the couple stress substrate with an imperfect interface between them has been obtained. Dispersion equations for propagation of SH waves with perfectly bonded interface and slippage interface between two media are also obtained as particular cases. Effects of the degree of imperfectness of the interface are studied on the phase velocity of SH waves. The dispersion curves are plotted and the effects of material properties of both couple stress substrate and viscoelastic layer are studied. The effects of internal microstructures of the couple stress substrate in terms of characteristic length of the material are presented. The effects of heterogeneity, friction parameter and thickness of the viscoelastic layer are also studied on the propagation of SH waves.
Źródło:
Journal of Theoretical and Applied Mechanics; 2017, 55, 2; 535-546
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of liquid loadings on lamb waves in context of size dependent couple stress theory
Autorzy:
Sharma, V.
Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/949331.pdf
Data publikacji:
2015
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
couple stress
characteristic length
Lamb waves
elastic waves
liquid loadings
Opis:
For understanding the effects of an internal microstructure, generalised microcontinuum theories with additional microstructural parameters are developed. One such a parameter, called the characteristic length of the material comparable with the internal cell size of the material is involved in the couple stress theory. The problem of propagation of Lamb waves in a plate with an internal microstructure and loaded with an inviscid liquid on both sides is studied using the couple stress theory. The dispersion equation of Lamb waves with the liquid loadings is derived. The impact of the liquid loadings is studied on the propagation of Lamb waves. The effect of the characteristic length is also studied on the phase velocity of Lamb waves in the plate for various modes in the presence of liquid loadings.
Źródło:
Journal of Theoretical and Applied Mechanics; 2015, 53, 4; 925-934
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling and characterization of laser welded incoloy 800 HT joints
Autorzy:
Arun Kumar, S.
Paulraj, S.
Powiązania:
https://bibliotekanauki.pl/articles/102190.pdf
Data publikacji:
2016
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
incoloy 800 HT
laser welding
modeling and simulation
mechanical and metallurgical characteristics
Opis:
This study aims at finding the effect of laser welding speed on incoloy 800 HT. This alloy is one of the potential materials for Generation IV nuclear plants. Laser welding has several advantages over arc welding such as low fusion zone, low heat input and concentrated heat intensity. Three different welding speeds were chosen and CO2 laser welding was performed. 2D modeling and simulation were done using ANSYS 15 to find out the temperature distribution at different welding speeds and it was found that an increase in the welding speed decreased the temperature. Mechanical properties such as tensile strength, toughness and hardness were evaluated. The effect of welding speed on metallurgical characteristics was studied using optical microscopy (OM), Scanning Electron Microscopy (SEM) with EDS, X-Ray Diffraction (XRD) technique and fractographic analysis. From the results it was found that high welding speed (1400 mm/min) decreased the joint strength. The M23C6 and Ni3Ti carbides were formed in a discrete chain and in a globular form along the grain boundaries of the weld region which increased the strength of the grain boundaries. Fractographic evaluations of the tested specimens for welding speed (1000 and 1200) mm/min showed deep and wide dimples indicating ductile failures.
Źródło:
Advances in Science and Technology. Research Journal; 2016, 10, 30; 115-126
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of Heat Input on the Mechanical and Metallurgical Characteristics of TIG Welded Incoloy 800HT Joints
Autorzy:
Arun Kumar, S.
Sathiya, P.
Powiązania:
https://bibliotekanauki.pl/articles/356231.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
incoloy 800 HT
corrosion
aging
sensitization
heat input
Opis:
This study focuses on the effect of heat input on the quality characteristics of tungsten inert arc gas welded incoloy 800HT joints using inconel-82 filler wire. Butt welding was done on specimens with four different heat inputs by varying the process parameters like welding current and speed. The result indicated that higher heat input levels has led to the formation of coarser grain structure, reduced mechanical properties and sensitization issues on the weldments. The formation of titanium nitrides provided resistance to fracture and increased the tensile strength of the joints at high temperatures. Further aging was done on the welded sample at a temperature of 750°C for 500 hours and the metallographic result showed formation of carbides along the grain boundaries in a chain of discrete and globular form which increased the hardness of the material. The formation of spinel NiCr2 O4 provided oxidation resistance to the material during elevated temperature service.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 3; 1673-1679
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Comparative Study on Ballistic Behaviour of MWCNT / Graphene Reinforced AL6061 Surface Composites Fabricated Via Friction Stir Processing
Autorzy:
Magarajan, U.
Suresh Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/27324483.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czasopisma i Monografie PAN
Tematy:
ballistic behaviour
friction stir processing
graphene
Multi Walled Carbon Nano Tubes
depth of penetration
Opis:
In this work, a comparative study on the ballistic behaviour of friction stir processed AL6061 targets had been made. Base Metal AL6061 (BM) plates with 25 mm thickness were friction stir processed by adding Multi Walled Carbon Nano Tubes (MWCNT) and Graphene (G), producing AL6061-MWCNT and AL6061-G surface composites. Optical microscopy and microhardness test on BM, AL6061-MWCNT and AL6061-G samples were performed as per the standard procedure. It was noticed that uniform dispersion of ceramic particles and refined grains were obtained for the friction stir processed surface composites. From the microhardness test, it was perceived that friction stir processing had induced strengthening of surface composites, hence increasing the microhardness of AL6061-MWCNT and AL6061-G by ~60.3% and ~73.6% respectively. Also, ballistic experiments were conducted at 680±10 m/s by impacting Ø7.62×51 mm projectiles. AL6063 backing plates were placed to compare the ballistic behaviours AL6061-MWCNT and AL6061-G targets by depth of penetration. It was noted that the depth of penetration of AL6061-MWCNT and AL6061-G targets were 37.81% and 65.84% lesser than the BM target. Further, from the results of Post ballistic microscopy it was observed that the microstructure near and away from the penetration channel edge looks unchanged in BM target. However, the AL6061-MWCNT and AL6061-G targets showed considerable change in their morphology, by forming Adiabatic Shear Bands.
Źródło:
Archives of Metallurgy and Materials; 2023, 68, 2; 541--550
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research on hybrid modified pathfinder algorithm for optimal reactive power dispatch
Autorzy:
Suresh, V.
Senthil Kumar, S.
Powiązania:
https://bibliotekanauki.pl/articles/2086822.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
optimal reactive power dispatch
ORPD
real-power losses
pathfinder algorithm
PFA
modified pathfinder algorithm
mPFA
hybrid pathfinder algorithm
HPFA
optymalna dyspozycja mocy biernej
strata mocy rzeczywistej
algorytm wyszukiwania najkrótszej drogi
algorytm wyszukiwania najkrótszej drogi zmodyfikowany
algorytm wyszukiwania najkrótszej drogi hybrydowy
Opis:
Hybridization of meta-heuristic algorithms plays a major role in the optimization problem. In this paper, a new hybrid meta-heuristic algorithm called hybrid pathfinder algorithm (HPFA) is proposed to solve the optimal reactive power dispatch (ORPD) problem. The superiority of the Differential Evolution (DE) algorithm is the fast convergence speed, a mutation operator in the DE algorithm incorporates into the pathfinder algorithm (PFA). The main objective of this research is to minimize the real power losses and subject to equality and inequality constraints. The HPFA is used to find optimal control variables such as generator voltage magnitude, transformer tap settings and capacitor banks. The proposed HPFA is implemented through several simulation cases on the IEEE 118-bus system and IEEE 300-bus power system. Results show the superiority of the proposed algorithm with good quality of optimal solutions over existing optimization techniques, and hence confirm its potential to solve the ORPD problem.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2021, 69, 4; e137733, 1--8
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies