Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "81.05.Ni" wg kryterium: Temat


Tytuł:
The Characteristics of Alumina Particle Reinforced Pure Al Matrix Composite
Autorzy:
Parvin, N.
Rahimian, M.
Powiązania:
https://bibliotekanauki.pl/articles/1490878.pdf
Data publikacji:
2012-01
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
Opis:
$Al_2O_3$ is widely used as the reinforcing additive in the metal matrix composites. The influence of $Al_2O_3$ particle size on the density, hardness, microstructure, yield stress, compression strength, and elongation of the sintered $Al-Al_2O_3$ composites were investigated. In the present study, 10 wt% of $Al_2O_3$ powder with three different particle sizes (3, 12 and 48 μm) were used in the production of the samples. Powder metallurgy technique was utilized to obtain more homogeneous $Al_2O_3$ distribution across the composites. The samples were cold pressed at 440 MPa, and sintered at 550C for 45 min. Results showed that the relative density of the composite was initially increased with decreasing particle size. However, it was decreased with further particle size reduction. It was also pointed out that the mechanical properties of the specimens were increased with decreasing particle size. The grain size and particle distribution homogeneity was decreased with raising the particle size.
Źródło:
Acta Physica Polonica A; 2012, 121, 1; 108-110
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Physical Properties and Microstructural Characterization of Mechanically Alloyed and Sintered W-2wt%B₄C-xwt%C (x=0, 0.25, 0.5, 1) Composites
Autorzy:
Sönmez, S.
Öveçoğlu, M.
Powiązania:
https://bibliotekanauki.pl/articles/1032548.pdf
Data publikacji:
2017-01
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
Opis:
Mechanical alloying processes were carried out in a Spex mixer/mill to synthesize W-2wt% B₄C-xwt% C (x=0, 0.25, 0.5, 1) powders for durations of 1 and 9 h in argon atmosphere. Mechanically alloyed powders were consolidated into green compacts by uniaxial cold press under 500 MPa and solid phase sintered at 1770°C under hydrogen and argon atmospheres for 1 h and 5 h. Effects of milling duration as well as C addition on the microstructural and mechanical properties of the sintered W-2wt% B₄C-xwt% C composite samples were investigated. The microstructural and mechanical characterizations of the sintered samples were carried out by scanning electron microscope, energy dispersive X-ray spectroscopy, X-ray diffraction, and Vickers hardness analyses. Density measurements and hardness measurements of the sintered samples were also carried out.
Źródło:
Acta Physica Polonica A; 2017, 131, 1; 193-196
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fractographic Evaluation of Crack Initiation and Growth in Al-CNTs Nanocomposite Fabricated by Induction Melting
Autorzy:
Mansoor, M.
Shahid, M.
Powiązania:
https://bibliotekanauki.pl/articles/1402016.pdf
Data publikacji:
2015-08
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
Opis:
Presence of reinforcement material in the matrix plays a vital role in modifying the fracture topography besides mechanisms of deformation and strengthening of a composite. In the present study, Al-CNT composite was prepared using induction melting technique. The composite was cast into copper mold and cold rolled to ≈95% reduction in thickness. In as rolled condition, the composite exhibited a simultaneous increase in yield strength (>70%), tensile strength (>50%) and hardness (>40%). The fracture surfaces of the broken tensile specimens were studied using scanning electron microscope. It was observed that the crack initiation was occurred in the matrix followed by void link-ups for its growth. Micro cracks initiation in the matrix played a vital role to sustain the ductility of the material.
Źródło:
Acta Physica Polonica A; 2015, 128, 2B; B-276-B-278
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dependence of Impact Resistance of Steel Fiber Reinforced Concrete on Aggregate Origin
Autorzy:
Sezer, G.
Yazıcı, Ş.
Sezer, A.
Powiązania:
https://bibliotekanauki.pl/articles/1402423.pdf
Data publikacji:
2015-08
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.05.Lg
Opis:
In this study, the effect of aggregate origin on impact resistance of steel fiber reinforced concrete was investigated. Using gravel-sized limestone, basalt and natural aggregates of 20 mm of maximum size, normal and steel fiber reinforced concretes were produced. Water/cement ratio and cement dosage of concrete mixtures were 0.5 and 400 kg/m³, respectively. It should be noted that superplasticizer and steel fibers were used in concrete production. Hooked-end bundled steel fibers with l/d ratio of 65 and 1.0% fiber volume were used. After 28 days standard curing, compressive strength, split tensile strength and ultrasonic pulse velocity tests were performed on 150 × 150 × 150 mm³ cube specimens. Additionally, impact resistances of concrete specimens were determined using impact test apparatus described in ACI Committee 544. Φ150 × 300 mm³ cylinders were prepared for impact resistance tests. After 28 days curing, these specimens were cut into Φ150 × 64 mm³ dimension. Impact resistance tests were performed on these specimens. Experimental results were evaluated in terms of steel fiber presence and aggregate origin.
Źródło:
Acta Physica Polonica A; 2015, 128, 2B; B-37-B-39
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Use of Mechanical Alloying for Production of Aluminium Matrix Composites with Non-Agglomerated Nanodiamond Reinforcing Particles
Autorzy:
Popov, V.
Prosviryakov, A.
Sagalova, T.
Többens, D.
Kiryukhantsev-Korneev, Ph.
Powiązania:
https://bibliotekanauki.pl/articles/1375581.pdf
Data publikacji:
2014-10
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.20.Ev
Opis:
Agglomeration is the main problem that prevents large-scale implementation of nanodiamonds in the production of composites. Mechanical alloying was applied for crushing the agglomerates and to obtain uniform distribution of the primary nanodiamond particles in aluminium matrix composites. The commonly used X-ray diffraction method fails to detect non-agglomerated diamond nanoparticles 5 to 6 nm in size, if they are incorporated in a metal matrix. Synchrotron radiation was used for the identification of non-agglomerated nanodiamonds. Scanning electron microscopy and synchrotron investigation showed that mechanical alloying does not lead to transformation of the diamond structure into other allotropic forms of carbon and the nanodiamond reinforcing particles are uniformly distributed in the aluminium matrix.
Źródło:
Acta Physica Polonica A; 2014, 126, 4; 1008-1011
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of SiC Particle Size on Properties of Cu-SiC Metal Matrix Composites
Autorzy:
Celebi Efe, G.
Altinsoy, I.
Ipek, M.
Zeytin, S.
Bindal, C.
Powiązania:
https://bibliotekanauki.pl/articles/1491445.pdf
Data publikacji:
2012-01
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.20.Ev
Opis:
This paper was focused on the effects of particle size and distribution on some properties of the SiC particle reinforced Cu composites. Copper powder produced by cementation method was reinforced with SiC particles having 1 and 30 μm particle size and sintered at 700°C. Scanning electron microscopy studies showed that SiC particles were dispersed in copper matrix homogeneously. The presence of Cu and SiC components in composites were verified by X-ray diffraction analysis technique. The relative densities of Cu-SiC composites determined by Archimedes' principle are ranged from 96.2% to 90.9% for SiC with 1 μm particle size, 97.0% to 95.0% for SiC with 30 μm particle size. Measured hardness of sintered compacts varied from 130 to 155 HVN for SiC having 1 μm particle size, 188 to 229 HVN for SiC having 30 μm particle size. Maximum electrical conductivity of test materials was obtained as 80.0% IACS (international annealed copper standard) for SiC with 1 μm particle size and 83.0% IACS for SiC with 30 μm particle size.
Źródło:
Acta Physica Polonica A; 2012, 121, 1; 251-253
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation of Radiation Shielding Properties of Polypropylene Fiber Reinforced Shotcrete
Autorzy:
Çakıroğlu, M.
Powiązania:
https://bibliotekanauki.pl/articles/1186770.pdf
Data publikacji:
2016-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
78.20.Ci
Opis:
Fibre concrete has emerged in order to improve the properties of concrete and to create an economical building material. In this study, the radiation permeability of shotcrete reinforced with polypropylene fiber was investigated. For this purpose, linear attenuation coefficient was measured for shotcrete reinforced with polypropylene fiber, produced using the dry mixing process. The linear attenuation coefficients for dry mixed shotcrete have been measured at photon energies of 1173, 1332 and 662 keV. Measurements were carried out using gamma spectrometer containing NaI (Tl) detector and a Multichannel Analyzer (MCA). The linear attenuation coefficients have increased with the increasing fiber percentage for all studied gamma energies.
Źródło:
Acta Physica Polonica A; 2016, 129, 4; 705-706
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparing of Commercial and Cemented Cu-SiC Composites
Autorzy:
Celebi Efe, G.
Altinsoy, I.
Yener, T.
Ipek, M.
Zeytin, S.
Bindal, C.
Powiązania:
https://bibliotekanauki.pl/articles/1287723.pdf
Data publikacji:
2014-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Bx
81.05.Je
81.05.Ni
Opis:
SiC with 30 μm particle size reinforced copper composites have been fabricated by powder metallurgy method and sintered at 700C for 2 h in open atmosphere. Copper powder was produced by cementation method and obtained as commercial for comparing. Cemented and commercial copper powders were reinforced with SiC having 30 μm particle size at ratios of 0, 1, 2, 3, and 5 wt% for improving mechanical properties of copper without decreasing the electrical conductivity. The presence of Cu and SiC which are dominant components in the sintered composites were confirmed by X-ray diffraction analyses technique. Scanning electron microscope showed that SiC particles are distributed homogeneously in the copper matrix. The relative densities of Cu and Cu-SiC composites sintered at 700C are ranged from 98.0% to 96.2% for commercial Cu-SiC composites, 97.55 to 95.0% for cemented Cu-SiC composites, microhardness of composites ranged from 133 to 277 HV for commercial Cu-SiC composites and 127 to 229 HV for cemented Cu-SiC composites, and the electrical conductivity of composites changed between 95.6%IACS and 77.2%IACS for commercial Cu-SiC composites, 91.7%IACS and 69%IACS for cemented Cu-SiC composites. It was observed that there is a good agreement between cemented Cu-SiC and commercial Cu-SiC composites.
Źródło:
Acta Physica Polonica A; 2014, 125, 2; 417-419
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Composition and Microstructure of the Al-Multilayer Graphene Composites Achieved by the Intensive Deformation
Autorzy:
Czeppe, T.
Korznikova, E.
Ozga, P.
Wrobel, M.
Litynska-Dobrzynska, L.
Korznikova, G.
Korznikov, A.
Czaja, P.
Socha, R.
Powiązania:
https://bibliotekanauki.pl/articles/1375203.pdf
Data publikacji:
2014-10
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.05.uj
81.05.ue
81.05.uf
Opis:
The paper presents results of the studies concerning aluminum-graphene composites produced with use of step technique; first mechanical alloying of Al and graphene powders and later intensive deformation by the high pressure torsion. As a result small, thin and round samples of composites, about 10 mm in diameter were achieved. For comparison similar samples not containing graphene were investigated. The X-ray diffraction, transmission electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy were applied to study composites structures and analyze graphene content and atomic bonds. The Raman spectroscopy method suggested multilayer graphene, which could also be identified as the defected nano-graphite as a component of the composite structure as well as some small content of the aluminum carbides. The highly dispersed microstructures of aluminum matrices were identified with the transmission electron microscopy, showing difference between the samples produced with the increased number of rotations, leading to the increased deformation realized. This method revealed carbon and aluminum oxides in large amounts which is interpreted as a surface effect. This method suggested also formation of the carbon-metal and carbon-metal- oxygen atomic bonds, which might partially result from formation of the carbides.
Źródło:
Acta Physica Polonica A; 2014, 126, 4; 921-927
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characterization of Machined Surface by EDM for $Al//B_4C_{p}$ Composite Material
Autorzy:
Kasman, S.
Feray Guleryuz, L.
Ozan, S.
Ipek, R.
Powiązania:
https://bibliotekanauki.pl/articles/1399698.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.20.Ev
81.20.Wk
Opis:
In this study, electrical discharge machining process was performed to investigate the machinability of $Al//B_4C_p$ metal matrix composites manufactured by powder metallurgy. For this, an experimental layout was conducted by using full factorial design. In the analysis, there are three parameters of which one is at three levels and the remaining are two levels. Totally, 48 experiments were carried out. The surface roughness $(R_{a})$ was increased with increasing the current (C), pulse-on-time $(T_{on})$, pulse-off-time $(T_{off})$ and amount of particle (PR).
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 224-226
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation of Dry Sliding Wear Behaviour of $B_4C$ Particulate Reinforced Mg Matrix Composites
Autorzy:
Feray Guleryuz, L.
Ozan, S.
Uzunsoy, D.
Ipek, R.
Powiązania:
https://bibliotekanauki.pl/articles/1400050.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.20.Ev
81.40.Pq
Opis:
Currently some composite materials and related manufacturing methods especially particle reinforced magnesium matrix composites are among important research topics because of their superior properties over monolithic metals. $Mg-B_4C_{p}$ is the commonly used composite material for fabrication of light-weight functional components. Wear behaviour of particle reinforced magnesium matrix composites play critical role for potential application in industries such as automotive and aerospace. In this study, the dry sliding wear behavior of particle reinforced magnesium matrix composites manufactured by powder metallurgy with different amount of $B_4C_{p}$ (3,6,9 wt%) addition is investigated. Wear tests are performed on a pin-on-disk configuration against SAE 1040 steel counter body under constant load and sliding speed. The wear behaviour of particle reinforced magnesium matrix composites was evaluated as a function of $B_4C_{p}$ amount (wt%). After the wear test, worn surface of the samples was examined by scanning electron microscopy for pointing out the wear mechanism.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 488-489
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
An Experimental Study for Machinability of $Al//SiC_{p}$ Metal Matrix Composites by Laser
Autorzy:
Kasman, S.
Ozan, S.
Feray Guleryuz, L.
Ipek, R.
Powiązania:
https://bibliotekanauki.pl/articles/1399697.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.20.Ev
81.20.Wk
Opis:
In this study, the laser milling process was used to investigate the machinability of particle reinforced aluminum matrix composites manufactured by powder metallurgy having different amount of $SiC_{p}$ (5, 10, 20 wt%). In this context, the laser parameters like scan speed and fill spacing were associated with the $SiC_{p}$ amount in aluminum (Al) matrix. According to the experimental results, the scan speed is dominant factor on both milling depth and surface roughness. Also, the reinforcement particle amount (wt%) is the effective factor but there is no detected significant relation between the surface roughness and reinforcement particle amount. However, the change in milling depth has been linearly changed with the increase of reinforcement particle amount.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 221-223
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics Bronze/$Al_2O_3(Ni)$ Reinforcement Metal Matrix Composite Produced by Current Activated Sintering
Autorzy:
Uysal, M.
Karslioğlu, R.
Akbulut, H.
Alp, A.
Powiązania:
https://bibliotekanauki.pl/articles/1399704.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.20.Ev
81.40.Pq
Opis:
In this study, a bronze matrix (90 wt% Cu + 10 wt% Sn) was reinforced with $Al_2O_3$ particles using mechanical alloying and then produced by a subsequent rapid current sintering technique. The mechanically ball milled bronze powders were reinforced with electroless Ni coated 20 vol.% $Al_2O_3$ particles with three different particle sizes of 90, 70, and 50 μm. Microhardness testing, and scanning electron microscopy were used for the structural characterization of the composites. The tribological behavior of the resultant composites was tested by the ball-on-disk method at 1.0 N applied load with 0.3 m/s sliding speed for determination the wear loss and friction coefficient features against a counterface steel ball.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 235-237
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Process Parameters of EDM on the Surface Roughness of Aluminum Matrix Composites Reinforced with SiC Particulates
Autorzy:
Feray Guleryuz, L.
Ozan, S.
Kasman, S.
Ipek, R.
Powiązania:
https://bibliotekanauki.pl/articles/1399967.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Ni
81.20.Ev
81.20.Wk
Opis:
This paper investigates the effect of electrical discharge machining parameters on the surface roughness as an alternative method for machining of $Al//SiC_{p}$ metal matrix composites produced with the powder metallurgy. Current, electrode type, pulse-on-time, particle reinforcement weight ratio and voltage were used as the process parameters. An experimental plan $(L_{18})$ was constituted by using the Taguchi orthogonal design. Results of experiments showed that pulse-on-time (34%) and current (31.26%) is the most influencing parameters. Besides this, the percentage contribution of particle reinforcement on the surface roughness is 6.71%.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 421-423
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
"Mechanical Alloying-Compaction-Electroplating" as Technological Scheme for the Development of Nanocomposite Coatings
Autorzy:
Popov, V.
Powiązania:
https://bibliotekanauki.pl/articles/1375576.pdf
Data publikacji:
2014-10
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.15.Pq
81.05.Ni
81.20.Ev
Opis:
A novel technique of producing composite electrochemical coatings with non-agglomerated nanodiamond reinforcing particles uniformly distributed in the matrix was developed. The technique is intended for coatings to be applied by transferring material from the anode to the cathode. The anode is fabricated using the mechanical alloying method that enables a composite with the uniform distribution of non-agglomerated nanoparticles to be formed.
Źródło:
Acta Physica Polonica A; 2014, 126, 4; 1005-1007
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies